Reviews
impossible
When I received the package and checked it immediately, I found that the Package had already been opened and the product itself was not in the package.
Why is this not noticed when packing?
I have used many different mail order services, but this is the first time I have seen such sloppiness and I feel bad.
I don't want to give even one star.
View detail
It was not enough.
There is nothing wrong with the functionality, except for the Bolt section Material:Plastic and molded BALI are also available and do not appear to be of very good quality.
There are similar MirrorRepair Parts by TANAX, which are made of Gold genus and have a much better finish. (but it is heavy + has a weird logo mark of Tanax)
View detail
I'm sorry.
There is nothing wrong with the functionality, except for the Bolt section Material:Plastic and molded BALI are also available and do not appear to be of very good quality.
There are similar MirrorRepair Parts by TANAX, which are made of Gold genus and have a much better finish. (but it is heavy + has a weird logo mark of Tanax)
View detail
For the first time Pulley
Quantity from NORMAL's mellow:Just by replacing a set of sets, you can run comfortably.
The Lightweight Pulley Boss can also be replaced for even better response.
View detail
JetSetting
Since it is a KEIHIN OEM, it is safe to use.
I lost it and purchased it, even though I adjust it based on temperature and humidity.
View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA MT03
Requires ingenuity in installation
Model YZF-R25
(8BKRG74) 2022 MODEL
I have prepared the following items to install the brake pedal side.
KITACOAluminum Bracket
BracketWidth:20mm/Thickness:3mm
Hole Size:φ6
Length:60mm
Spacing:40mm
YamahaOEM
Brake fluidReserverHolder
(2015 1WD-F582E-00)
JointZ type bracket with 3 holes
BoltM6×12、M6×15、M6×20
Flange nutM6
Mounting position is set at 60mm back and 40mm up, which is the position with the least interference.
On the shift pedal side, the included shift rod does not fit well, so it will be replaced at a later date.
After the installation, I think it was better to check the position here than to buy expensive Rear Sets and make a mistake. I learned a lot.
View detail
Fits: YAMAHA MT03, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA MT-03, YAMAHA MT-25
Judder may be less.
It has been running close to 50,000 km, so we installed it together with the replacement of the Clutch board.
The clutch spring was also newly installed, and after assembly, there is no extreme large change in the running feel, but the slight vibration seems to have been reduced.
I may change Fee Ring in the future as I get more comfortable with Clutch, but so far I have no complaints.
It was easy to install and I'm glad I bought it.
View detail
Easy to customize
Double-sided tape is all that is needed, so anyone can easily attach it.
The price is cheap, so I bought it thinking it would be okay if it failed, but it feels and looks great!
View detail
Fits: HONDA CB750F, HONDA CB1100R, HONDA CBX1000
OEM and length was different.
I bought it because it's hollow and it's by Vito, but it's shorter than OEM and I can't install it on my footpeg.
I didn't see it in the description, so here it is.
View detail
Pre-cut and inexpensive
I usually buy rubber mats and cut them, but this product is pre-cut and at this price, so there is no extra hassle.
Grip is also good.
View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA MT03
Brake Side
Model YZF-R25
(8BKRG74) 2022 MODEL
Brake Side Image
View detail
Fits: SUZUKI SV650 N, SUZUKI DL 650 XT V-Strom, SUZUKI DL 650 V-Strom
The CP is also good.
From the name PyramidPlastic, I was prepared to order some more cheap products.
In fact, the FRPParts arrived with a high degree of precision, which is quite high for exterior Parts from overseas.
The bracket engages the Crankcase Bolt firmly, and the engagement with the FRP part is not bad.
However, the supplied Bolt is a bit short, so you may want to prepare a Bolt of about +5mm.
It is not impossible to stick to FRP, but it does not put a load on FRP, and above all, it increases work efficiency by a large margin.
In fact, a separately purchased DesignBolt was used for installation.
I have the impression that it took quite a long time, but it is because it is an overseas parts.
Considering that the FRP parts are solid and cost only 20,000 yen, the cost performance is also good.
View detail
Fits: HONDA CB1100F, HONDA CB900F, HONDA CB750F
Watch out for small parts.
First of all, when you take it out of the box, there is an E-shaped Snap ring in a small bag, so you might lose it if you open the bag carelessly. I found the Snap ring in the Instruction Manual, and found it lying at my feet.
Next, in the Instruction Manual, the footpeg is removed and the U-shaped plate is fixed with a bolt, but there is a small ball on the footpeg and a spring holding it down, so the ball will fly off with the spring if it is not removed carefully.
When putting the footpeg back in, there is a plate between the U-shaped footpeg and the footpeg, so the footpeg and the plate sandwich the spring and the ball between the footpeg and the ball and hold it down to some extent while inserting the footpeg.
View detail
I saw that it was out of print, so I suppressed it.
Manufacturer OEMOption Parts.
I bought it because it is out of print and I thought I would hold on to it.
Yeah, failure.
White on Gun meta as per image (over Paint or Seal) [Color] (Clear?) It was.
The one up in the product image looked Black.
In any case, Out for Mat silver bodywork.
It would have been better if it were black instead of the shiny gun meta.
Two bright, flashy colors that are not on the body of the car.
Parts that would look good on a Black SV from Gun meta.
I tried Silver as a trial, but the Fit feeling is not so good.
Paint was returned and sealed to the Stock shelf as a testFit only item.
View detail
It's not Kang Tan, right? LOL!
In the product name Kang Tan." but it is not such a kantan to be installed on ELIMINATOR 400.
I don't mean difficult, I mean tedious lol.
To begin with, the problem is on the body side, but the Tank has to be removed in order to install the 4-poleRelay.
This is a pain in the ass, lol.
The product itself is solid, and the Harness fits inside the MeterCowl, so it is a good reflection.
I think it will be around the Handlebar when the retrofit USB Socket is installed, so it will be easy to handle the Wiring! (,,> <,,)
As mentioned earlier, the product received a perfect score except for the 4-poleRelay installation.
View detail
Excellent visibility
This one is used for CRF250RLY50 MOTARDSpec.MD44 and my car Swift Sports31s
It is inexpensive, highly visible, and the cap is easy to remove, so it is great for Small students who check their air pressure frequently.
My only regret is that when I purchased this item from Webig, it was somehow shipped as a Single Item, even though I requested that it be combined with an order that was waiting for another item to arrive.
I was very irritated that I had to pay a ridiculous shipping fee for an item that cost less than 100 yen.
View detail
This is good.
The shape of the mirror is designed to avoid the arm holding the handlebar, so the visibility is surprisingly good, and the bracket is thin, so it may be good to be less assertive.
The Mounting Base is a little large, so I adjusted it with a washer so that there would be no wound left on the cowl when tightening it.
View detail
Carbon
Scratches on the Black colored Tank are inevitable, so install it before it gets worse.
It is easy to apply with double-sided tape.
The seam between the Tank and Seat is also rounded off so that it does not look out of place.
However, the part without Tape is creaking" when pressed, so it might be better to add more Tape.
Some edges are not able to follow the subtle curvature of the tank, but I don't mind.
View detail
Baffle replacement for OEM exhaust system with R-EVOTitaniumium silencer from beams
I purchased a new OEM exhaust system from beams R-EVOTitaniumium silencer, but the volume was not enough, so I replaced it with this Semi-racing baffle, and the size fits perfectly!
The sound quality is a little lower than with the Baffle, and it is not too quiet and not too loud, but just right.
View detail
heavy
Heavy.
I felt Fashion had a lot of personality,
It is too heavy, partly thanks to unnecessary design.
The construction is sturdy and easy to see without blurring.
The Handlebar area is too heavy to be operable.
We ended up reverting to OEM.
View detail