Reviews
Excellent product, very, very well made. Installing is not an easy job, but that's due to W800 mechanics
This is an excellent product. I am installing a plush comfort seat which is slightly higher, and with these bars the geometry is perfect for touring. Quality is top notch. Everything is very well made, everything fits and well thought through. I would not try to install it unless you are capable enough to build the bike ground up. On mine, tank and light had to come off on top of obvious cables, break lines, etc. 4 hour job easily. If you are anything less than a master, give it to your trusted mechanic and pay accordingly. In case of W800, it is just how the bike is laid out, not a a fault of this product. In fact, because of everything fits so well, Hurricane have made it as easy as at all possible for this Kawasaki. View detail
Inexpensive and practical
Inexpensive and practical.
Necessary and sufficient
View detail
Inexpensive and practical
Inexpensive and practical.
Necessary and sufficient
View detail
Inexpensive and practical
Inexpensive and practical.
Necessary and sufficient
View detail
Fits: HONDA CB1100, HONDA CB1300SUPER BOLDOR, HONDA FTR223, HONDA NC700X, HONDA MONKEY, KAWASAKI 250TR, KAWASAKI W400, SUZUKI RV200 VANVAN, SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER Big Boy, SUZUKI GRASS TRACKER Big Boy, YAMAHA TW200, YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW225E
Type 2 to Type 3
I was using a Police Type 2 and changed to a Type 3 to get a little more up.
The length of the wire was delicate and I had prepared a long wire, but it was better to use a narrower wire, so I was able to use an OEM wire.
I prepared another one and narrowed the width further to my liking at 655mm.
View detail
Bar handle has
I used to use 10cm Long on my HURRICANE Pipe Handlebar Kit, but it was too long, so I decided to use 5cm.
Clearance is just fine.
View detail
HURRICANE HURRICANE Reflector
The product was as per the Image.
There will be a gap between the Number and the Reflector, so we do not recommend this if you are concerned about this. (It will look like it is gnawing out of the Number.)
View detail
Fits: HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, KAWASAKI W400, KAWASAKI 250TR, HONDA MONKEY, HONDA MONKEY, HONDA HORNET250, HONDA NC700S, HONDA FTR223, HONDA FTR223, HONDA CB750, HONDA CB400SUPER BOLDOR, YAMAHA TW225E, YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW200, YAMAHA SR500, YAMAHA SR400
Best Match for Good Position XSR125.
The handlebar on my XSR125 did not fit and my shoulder stiffness got worse after the first ride, so I replaced it with this handlebar based on Net information.
I also bought a Flat continental2 type and compared it with the BMConti3 type while temporarily attaching it, and found that the BMConti3 type fit better.
It's so easy to ride that I think this should be the standard now! It is so easy to ride. I recommend it.
I had prepared a riser, but I am 175cm tall and it is just right without the riser.
Small patterned person is Quantity:SetBackRiser would be a good position.
Drilling is required, but a drill driver is sufficient for this purpose as long as the position is marked temporarily and the punch is firmly applied.
It is hang to go little by little while checking, not trying to open it all at once.
It was a good buy for the XSR125.
View detail
Price suitable
The screw holes were accurate and there are no problems with installation or appearance. View detail
Fits: SUZUKI RV200 VANVAN, SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER Big Boy
meticulous manufacturing
It was good up to the point of installing the Coupler on the body side of the NORMALIndicator with the Coupler, but the remaining Black color code was installed with Tap for Connection and the Instruction Manual's Sky blue code. The sky-blue code is used to connect to the Quantity:There are 2 pcs and the first connection failed, but I opened the Tap and connected it to the dark sky blue cord and it lit up fine. View detail
Fits: YAMAHA XJR400R, YAMAHA XJR400, YAMAHA V-MAX 1200, YAMAHA SRV250, YAMAHA SR400, YAMAHA FZR400, SUZUKI GSF1200, KAWASAKI ZR-7/S, HONDA Monkey BAJA, SUZUKI GSF750, YAMAHA XJR400, YAMAHA XJR1300, YAMAHA XJR1200R, YAMAHA XJR1200, YAMAHA SRX600, YAMAHA SRX400, YAMAHA SRX400, YAMAHA FZR250R, YAMAHA FZ400, SUZUKI BANDIT400
HURRICANE triangular table spindle nut
Exquisite workmanship, cheap price, good materials, beautiful colors, very accurate size, easy to install, and fits perfectly in the car View detail
Good position
I came across this product after doing a lot of research on the height and width of the Japanese Vehicle Inspection Correspondence on the CB750rc42.
The width is the same and the height is about 35mm higher than the other two, so I asked the shop that installed it to check if they had done the same thing and since it was compliant, they installed it without refusal.
Extension Harness was also prepared in case, but it was used only for Blinker switchWiring extension.
For this level of uplift, it would have been more cost-effective to just extend the Blinker switchWiring than to purchase Extension Harness.
The position is only 35mm up, but it feels much higher, and the handlebar feels a little tighter in the front, so it is very easy to drive.
It is as easy as if it were a learner's car, but the system is also very windy as it approaches vertical.
I am self-satisfied, but it was a good decision to replace it because it is totally easy to drive and maintain a non-fatiguing position.
View detail
excellent quality
Extremely solid, well made bars. I have fitted inverted for a low clubman style. Works well in combination with the bar end mirors and SSK adjustable levers. View detail
took a chance and it payed off
Snapped the original cable. Ordered the short cable for the standard Z900RS after fitting lower bars. Worked out within 10-15mm of the Z900RS Cafe OEM cable length. Great fit. Fast shipping as always. View detail
It's best.
Transforms into a classic look.
The driving position is very comfortable and stable.
Even if you drive for a long time, it will not put any strain on your body.
Handle replacement can be done quickly if you purchase the Hurricane extension harness together.
This is one of the customizations I am most satisfied with. -------------------------------------------------- -------- Transforms into a classic look. The driving position is very comfortable and stable. Even if you drive for a long time, it will not put any strain on your body. Handle replacement can be done quickly if you purchase the Hurricane extension harness together. This is one of the customizations I am most satisfied with. Powered by Google Translator
View detail
I was satisfied with the 3cm but Large change
After purchasing the Motorcycle, the seating position was not quite right and I had back pain after running for a little while. View detail
Impact is greater than expected!
Needed for car inspection? I bought it because I thought I might need it for my car inspection.
Bought it for the look of the picture and the price!
The texture etc., is very good.
When installed, it has a strong presence.
View detail
Unify colors.
I purchased a red colored MONKEY125 and have been gradually adding red colored parts to it.
I have done handlebar and front suspension, so I decided to purchase this product for the rear suspension as well.
I was originally considering Revolution products, but was hesitant because they cost about 10,000 yen, but I was able to purchase Made by HURRICANE for almost half the price here on this site.
The Rear Sprocket Cover seems to be a little shorter than the OEM one, but it looks SMART than the OEM BlackPlastic one.
There are various colors available, so I think it is suitable for dress-up.
I was Large satisfied with the purchase and installation.
View detail
Comfortable with easier Position than OEM
I felt uncomfortable with the OEM's too-wide handlebar, so I replaced it.
The Handlebar of the Cafe is narrower than the Z900RS, though,
The OEMHandlebar is so wide that you would think it was a STREETFIGHTER-type Handlebar, and it stiffens your shoulders.
The position that comes 3cm in front of the OEM by 3cm up with the width shortened by about 6cm will be a much easier position than the OEM.
I would not say that installation is difficult, but if you are not used to it, there may be a Large change.
The handlebar periphery is removed and replaced via an adapter since the diameter is narrower than the OEM.
This adapter gapes when the handlebar angle is adjusted, so it is necessary to check when tightening.
Also, when tightening the Handlebar Post, Brake Holder, and Clutch Holder
Be sure to tighten from the top and adjust the tightness on the underside, so be careful.
The LeftRight Switch Box and Accelerator WireHolder have pre-drilled holes, so no drilling is required.
OEM wire ends when replacing the supplied Clutch Wire. (Engine side) It is recommended to use Tie Wrap or Needle Goldetc. to tie the new wire to the OEM wire and pull it up so that it can be replaced through the same place as the OEM wire.
View detail
Fits: SUZUKI GSF750, HONDA CB400SF vtec Revo, HONDA CB400SF vtec III, HONDA CB400SF vtec II, HONDA CB400SF vtec I, HONDA HORNET600, KAWASAKI ZEPHYR400χ, KAWASAKI ZRX400 II, KAWASAKI ZEPHYR750 RS, KAWASAKI ZEPHYR750, SUZUKI INAZUMA400, SUZUKI GSX400, YAMAHA XJR400R, YAMAHA XJR400S, YAMAHA XJR400, YAMAHA XSR700, HONDA HORNET250, HONDA VTR250 LD, HONDA VTR250, HONDA CB400SF verS
Separate handle for HORNET
Ordered last August, finally arrived this February.
HURRICANE Inc. has been quite busy.
It was worth holding out to buy from a pre-priced reseller.
The work was easy as long as the Handlebar holes were drilled.
The Curve is nice and easy to bend because of the forward lean.
I am wondering if I should extend the Fork and put it on the Top Bridge as it is a bit tight.
View detail