Reviews
Conti II type can be NORMAL.
The OEMHandlebar is so large that if it is replaced with a narrower one, the OEM will have a little extra space.
However, it could be left as OEM, but it interfered with the RadiatorRight Side surface.
It is a product that is better to have than not to have.
View detail
took a chance and it payed off
Snapped the original cable. Ordered the short cable for the standard Z900RS after fitting lower bars. Worked out within 10-15mm of the Z900RS Cafe OEM cable length. Great fit. Fast shipping as always. View detail
Fits: YAMAHA XJR400, YAMAHA XJR400R, YAMAHA XJR400R II, YAMAHA XJR400S
I'm lighter
Clutch is now lighter.
Stainless mesh, so it seems to be durable.
View detail
Fits: YAMAHA XJR400, YAMAHA XJR400R, YAMAHA XJR400R II, YAMAHA XJR400S
Mesh
The mesh is durable and the Clutch is very light.
I would like to do this next time I replace it.
View detail
Fits: SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER Big Boy, SUZUKI GRASS TRACKER Big Boy
GRASS TRACKER It was a long time for BIGBOY.
It was too long for GRASS TRACKER BIGBOY. We managed to get it to fit in the car by working out how to handle it.
Clutch has been revived.
View detail
good quality, perfect fit
I bought this clutch cable along with throttle and choke cables. This cable is 100 mm/10 cm longer than stock but I had no problems about them. The fitment is great. Maybe in the future, I may install an ape hanger to my bike and I can use that extra 10 cms. View detail
Separate handle by all means!
If Separate handle is selected, the NORMAL clutch wire will be too much.
What kind of harm will be done?
The Clutch is not turned off, but it is turned off, or at worst, it gets tangled in the Wheel and becomes Large.
Shorting is necessary to prevent these problems.
It is -100mm shorter than NORMAL.
good point
When separate handle is used, the clutch is cut smoothly.
XX semi-cra is also easy.
There is also the rigidity of the ○Cable.
The price is also low.
A bad point
Installation is troublesome.
○Peasy to rust if lubrication is neglected.
I need a Cable that matches the length of the Handlebar.
For Separate handle, Normal cable should not be done in the sense of prevention.
View detail
awesome
awesome with my 8' bar on the rebel 500 same quality as the OEM cable this bit here is just for the body of this review to reach > 100 charaters geez View detail
HandlebarUp essentials
I had to upgrade my handlebar because the position was getting too tight, but I found this product when I was having trouble getting to the clutch cable. The installation was not difficult and I was able to replace it with the on-board tool. View detail
Reliable Manufacturer.
When I replaced the BEETTAPER Handlebar, the NORMAL Clutch Cable sagged.
I bought this one because it looked bad.
Above is the length Exactly to Handlebar.
View detail
Cable poking has been eliminated.
It may not be originally necessary, but in my case, the height of the Handlebar was about 2cm higher than that of the Normal vehicle because of the difficulty of leaning forward, and the Clutch Cable was sticking out when the Handlebar was set to the full Right position. So, we replaced it with a Long Type Cable. As a result, the tension of the cable was eliminated and it became very easy to operate the clutch when turning the U-turn. Although U-turns are rare, I think it is effective from the safety point of view to have eliminated one of the operational concerns in unfamiliar situations.
Since it was not an expensive product and the replacement work was simple, I strongly felt that I should have replaced it earlier.
Around Handlebar for reference (Height change) Attached is an image of the
View detail
Reliable external manufacturer's product
2022 Rebel 250 (MC49) I bought this for my Robot Handlebar. The size of the Thailand Ko is also Exactly, so it was easy to exchange.
In terms of length, I think 150mm Long is sufficient unless the Up Handle is very large.
View detail
It is a must for Continental handle.
When I exchanged the z900rs23 model with the HURRICANE Conti2 type, the Clutch Cable was long and it was a bit of a poor parenthesis because of the Dollar. I removed the cable from the engine side, and then removed the clutch side. I wrapped this product around the OEM Cable with Vinyl Tape and pulled it from the Engine side. I was a little disappointed, but the Cable also passed under the tank without any problem. I had a little trouble installing the cable on the engine side, but I managed to do it. The length is almost the same as OEM. View detail
I would like to see an assortment in 5 cm increments.
Purchased to change the OEM Handlebar of a MONKEY125 to a Handlebar Up Type.
I bought a 200Millimeter long, but I really wanted a 150mm longer one.
No complaints about the feel of the product. 。 Sliding was good even without going through Oil.
View detail
Nice
I bought and replaced the fat condor handle bar from the hurricane company. It is compatible with genuine clutch cables, but the cable on the clutch case side is stretched out, so it is perfect to purchase and install the above product. It took about an hour when I replaced it by myself. I think it took some time because it's my first time. View detail
HURRICANEClutch Cable
Clutch Cable was cut off.
I tried to buy OEM Product!
HURRICANE's Clutch Cable is less expensive.
I bought it instantly!
It's a safe Manufacturer, so it's a Recommendation!
View detail
I bought the same one as before.
Quantity when the Handlebar was previously replaced.:Longer Clutch Cable that came as a set.
I don't have much to say in detail because I just purchased the same product in Single Item, but it helped me because the Clutch, which was very stiff, became very light.
View detail
Good
I replaced the Z900RS Handlebar with Musashi Kai Fat bar.
I purchased this product because the clutch cable was too tight. The quality of the cable is similar to that of OEM cables, so I am satisfied with the large cable.
View detail
Not for me.
I think it's partly because I'm inexperienced, but no matter how I adjust, the Clutch drag happens.
I spent several hours checking the details, but eventually gave up without a cure.
View detail
Long is difficult to handle,...
[How is it used?
Used for SEROW225 (1KH).
The clutch was feeling a little heavy, so I replaced the clutch cable with a feeling of God's help.
The OEM was a little expensive, and this one from HURRICANE was a little cheaper, although it was Long, so we chose this one.
Was the one you received as per Image?
It was as per Image, maybe 15~20 cn longer than OEM.
Was the installation difficult?
Since it was a little longer than the OEM, we had to be a little creative in handling it. To be honest, I wished the OEM length was longer.
The connection between the Clutch Cable and the Engine Case is simple, but a little confusing.
You should take a good picture or something before you remove it to document how it was attached.
How was your experience with it?
I think it is slightly lighter. I think it can be lighter depending on how it is handled.
[Included Parts:were they on?
A white plastic cover is attached to the end of the clutch lever side of the clutch cable.
I am... Packaging Cover?" I thought, "I took it, but that is to be used as it is....
[Was there anything that disappointed you?
None
Other items that would be helpful
Items to buy together
I recommend this for lubricating Wire, although it is a bit expensive. You can throw it away except for this.
https://www.webike.net/sd/23380063/
View detail