Reviews
All in all, I think it's a product that is worth the price
This is a Fender Eliminator Kit for the GSX-S1000, order it now I haven't received it yet, so I don't know how it feels or the texture of things etc
As you can see in the product description image, the position of the blinker is a little bit far from the number, so I'm worried about it Some of you may be
Also, you need a reflector, so it would be nice if you could include one with this package
View detail
It's a good, solidly built product
It was inexpensive, well-built, and easy to install
The other Fender Eliminator has a gap between it and the stop lamp and I don't like it very much is not, and this product is great because it doesn't have that, and it doesn't feel different!
I'm glad I refreshed the rear area and purchased it
View detail
It's a good costumer and looks great
When I bought the GSX-S1000, it was my first Custom for the HURRICANE I threw in the Fender Eliminator Kit
The installation system is perfectly fine, and the Installation Instruction Manual is included I think it can be installed easily in about 30 minutes if you do it while watching it In addition, the cheap price and the wiring process of the position lamp is very easy to install I liked the fact that it was unnecessary
The only complaint I have is that the Reflector is a Quantity:The point is that it is not a set and must be purchased separately
Recommendations for those who don't care about the brand, and who care about the costumes I think it's a product
View detail
○
I installed it in MODEL of 2020/2/20 release, but it can be installed and used without a problem
Naturally, the bounce is great
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
Clean around the rear!
GSX1300R HAYABUSA 10 years old, installed for use in North America
It's pretty neat around the rear! I don't like the raggedy OEMRear Fender, and the Fender We recommend "Made by HURRICANE" which is the cheapest Eliminator Kit available It is
Installation is easy if you can remove the rear cowl, Couplet-on for easy installation It is
In my opinion, I would have liked the Number angle to be a little higher
It also comes with a License Plate Light, but it's not that bright
It doesn't have a Reflector, so you need it separately for inspection
Overall, the Rear area is cleaner and the Number is angled, which makes it look very It gets better
View detail
It was refreshing
The big and stupid OEM Fender is not cool, so I changed it immediately It took me a long time to install it because it was unexpectedly large However, it is not difficult because a lot of exchange examples are written in Net It is necessary to prepare the License Plate separately Screw at the back of OEM Fender is very hard because the screw lock agent is painted on it You need to be careful not to nip the Screw (I nipped it and forced the cord out.)
Because the Wiring is reused as it is, the back of Seat is Wiring to the extent that the Fender became short It's a mess in
I think that there is no role as a Fender almost, so if you drive on a rainy day, you can use the Mud Guard I think you should put it on
View detail
Fits: HONDA VTR250, HONDA VTR TypeLD
If you put it on the VTR250Fi, it will have a gap
We purged the entire OEMRear blinker and tail lamp
Installation itself is very simple
However, there is a hole in the Blinker's area that is brilliant
Rear blinker is integrated with the License Plate We need to do something about this hole
We decided to process and fill the AluminumAngle at a later date and fill it with Sponge until then I left it on
It was pretty SMART from a distance
It is not this product that needs processing, but the surrounding items
View detail
Refreshing look and feel
I didn't like the long tail of NORMAL, and I also bought the L Size body cover The height of the tail is just short of the height of the HURRICANE Therefore, I decided to install the Fender Eliminator, a HURRICANE The Fender Eliminator is further out than the other Manufacturer's So I decided to expect a slight Mudguard effect
I would have liked the instruction manual to be a little more detailed, with BlinkerWiring's handling of it and I had trouble dealing with the RearSub harness
View detail
Fits: YAMAHA MT-09 To Racer, YAMAHA TRACER900, YAMAHA TRACER900
Cannot be used by those who wear the side case
Side case and Blinker interfere with each other, so you can't use it
(I put it on as a Large mod.)
If you don't use the Side case, I think it's a good thing it's cheap
View detail
Fits: HONDA CB400SF, HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR
Cool
Reflector is the license plate base of CB400SF (sold separately) I purchased a The assembly, wiring, etc., can be installed comparatively plainly by the Construction Manual, and it is possible to be installed The LED is also very nice and sharp It's solid and I'm happy with it The installation took about 4 hours to complete, with Wiring taking a long time to put away View detail
The overall construction is simple and nice
When I checked each Parts to install it, the base of the License Plate Light The wiring on the part was peeling off and the wire inside was exposed, I can't roll the Tape Since there were only two holes, I repaired them with a Glue gun before installing them The accuracy of the mounting holes, etc. was able to be installed on Smooth without any problems It looks and feels good View detail
Happy!
It's affordable, easy to install, and you don't have to sacrifice the Loading Hook I am very satisfied with it If you are worried about installing it yourself, there is a person who uploads a video of how to install it on the net Please look for it and see if you can find it View detail
Very Refreshing!
I installed the Fender Eliminator Kit It feels heavy, but it's very Refreshing and refreshing Lol
I hesitated to choose Takagawa when I chose the Manufacturer, but I decided to choose License The Plate Light was a NORMAL diversion and I changed it to HURRICANE So I decided to use HURRICANE; I installed HA5796 Reflector (also HURRICANE)
After installing, I ran the car, but Chatter occurred in Number and Base Then, I pasted it with a little thick Double-sided Tape and solved the problem!
RefreshingSMART monkies, done
View detail
Typical cheap and bad
To put it bluntly, it's a lazy product with a near defective design, so it's made by HURRICANE Don't buy the Fender Eliminator Kit for the SC77 from
Because it only comes with a Bracket for License installation and there is no Cover There will be a gap between the accessory case and inner fender Therefore, water or other contaminants may enter the Accessory Case or Inner fender under the Tandem seat Garbage, sand, Small stones etc., quite a lot of them get in
Moreover, because the Small stone etc. which Tire wound up hits the Accessory Case directly And the Accessory Case has been torn to pieces
In the product information, Base plate is Material:It is called Aluminum, but the license light Plate is made of steel and poorly painted
It's already pretty rusty despite being in use for less than six months
When I contacted the Manufacturer Our spec. is based on consideration of cost and fitting methods
So, I thought that the water etc. will be in the Spec. so I should be patient
For Accessory Case measures, you need to process aluminum plates etc. to make the Cover's It's better to buy a competitor's product from the beginning because you will have to make and repaint your own
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
I was able to install it on Kan Tan
It was cheaper than other companies, so I bought it There is no
Connector is also included, and is used to cut the Wiring on the MotorcycleBody It's easy to do without
View detail
That's good!
I wanted to Refreshing Rear, which was feeling heavy But I don't want to spend that much Cost
You can use the OEM Blinker and License Plate Light as it is I'm glad I did
I'm satisfied with the image
View detail
It looks good
User vehicle inspection failed due to light leakage from the license plate light, Touch pan I painted it and it passed I could see the white LED from right behind View detail
It's the only way
First of all, thank you, HURRICANE
I'm wearing an EnduranceCarrier, so I need to find something to wear with it I was looking for it
Endurance products developed at the same time are designed to be worn together However, when I look at the blogs of our ancestors who wore the boards, I can't even call it a gap It was in the form of water and mud all over the place
The ones that are available elsewhere are not perfectly shaped and impossible to wear together
A friend of mine was concerned first Maybe we can go to the HURRICANE? So, my friend and I had a look at HURRICANE's blog, and we had a paper Then I licked it around so much that it was scraped and punctured
And if you look closely at the shape, you'll see that it's not only shaped to fit the underside of the Seat Cowl The Blinker is also in a position where it doesn't interfere with the Carrier and there's nothing growing underneath the board
And the installation is exactly the same as the way to install the Carrier's Bracket It was a thing to fix with M6Bolt between the Spacer and the M6Bolt
Grin, Carrier's Spacer is 39mm, this Fender Eliminator If the Spacer is 15mm and the thickness of aluminum plate is 3mm, put a 21mm spacer between them If it's a good calculation
So, Posh's 20mmQuantity for M6:1 Set of 2 Spacers of 2pcs. and 1mm thick flat Washer for M6 I was able to install it by pinching it and co-tightening it
As I wrote in my blog, the gap between the individual differences is 1mm thick and 1 cm wide Sponge I used a type gap tape and managed to make it work
The angle of the Number is not that far up, so it's a zero, and my friend has a GSX-R750 with an ACTIVE I'm wearing the thing, but it was more slanted that way
License lamp and Reflector are fixed on both sides, Lamp is quite bright and Tail The area around the License Plate appears to be faintly pink because it is mixed with the lamp light is stylish
Since the Blinker also fits inside a little bit, the Cover is Smooth, and it's easy to put on and off The license plate is high and the seat is underneath the seat, so it's in the garage Stress has been reduced as you won't run into any ladders
This is my second motorcycle and the first time I've ever been on a Fender Eliminator Thank you again, HURRICANE, I got the sticker too! (Naps WebShop (angry) ) and put it on the back of the Upper CowlFront blinker ( Quantity:Pair (for Left and Right) ), it is Large change satisfaction in conjunction with Handlebar
View detail
Nice metal
The items is so great with the metal surface finishêd. The dark Red len of the Tail Light is impress. I like the items so much. View detail
If you're worried about the angle of Number, this is a good one
The Fender Eliminator Kit for the CB250R has been
KITACO was the only company available
About two companies have recently released their products
Since the CB250R does not have a tail cowl, each company has been using Bracket's
I can see how you struggle with the shape
The shape of the Bracket is refreshed and the angle of the License Plate is
45 degrees [Color] The only thing that is clear is HURRICANE
I don't want to get caught with a Fender Eliminator Kit for poor maintenance
HURRICANE
As a late entrant, the shape of Bracket is Refreshing
The License Plate Light is also made of LED, which is bright and not too radical in appearance
I love it
But the Instruction Manual is too assertive
If you're new to the site, take a picture with your phone before you lose your OEMParts
It's better to take it and work on it a little at a time
The OEM Blinker to be diverted is especially suitable for this, so you can use it at once
It's better to work one side at a time instead of doing it
View detail