【HURRICANE】Fenderless Kit Review
It's the only way
First of all, thank you, HURRICANE
I'm wearing an EnduranceCarrier, so I need to find something to wear with it I was looking for it
Endurance products developed at the same time are designed to be worn together However, when I look at the blogs of our ancestors who wore the boards, I can't even call it a gap It was in the form of water and mud all over the place
The ones that are available elsewhere are not perfectly shaped and impossible to wear together
A friend of mine was concerned first Maybe we can go to the HURRICANE? So, my friend and I had a look at HURRICANE's blog, and we had a paper Then I licked it around so much that it was scraped and punctured
And if you look closely at the shape, you'll see that it's not only shaped to fit the underside of the Seat Cowl The Blinker is also in a position where it doesn't interfere with the Carrier and there's nothing growing underneath the board
And the installation is exactly the same as the way to install the Carrier's Bracket It was a thing to fix with M6Bolt between the Spacer and the M6Bolt
Grin, Carrier's Spacer is 39mm, this Fender Eliminator If the Spacer is 15mm and the thickness of aluminum plate is 3mm, put a 21mm spacer between them If it's a good calculation
So, Posh's 20mmQuantity for M6:1 Set of 2 Spacers of 2pcs. and 1mm thick flat Washer for M6 I was able to install it by pinching it and co-tightening it
As I wrote in my blog, the gap between the individual differences is 1mm thick and 1 cm wide Sponge I used a type gap tape and managed to make it work
The angle of the Number is not that far up, so it's a zero, and my friend has a GSX-R750 with an ACTIVE I'm wearing the thing, but it was more slanted that way
License lamp and Reflector are fixed on both sides, Lamp is quite bright and Tail The area around the License Plate appears to be faintly pink because it is mixed with the lamp light is stylish
Since the Blinker also fits inside a little bit, the Cover is Smooth, and it's easy to put on and off The license plate is high and the seat is underneath the seat, so it's in the garage Stress has been reduced as you won't run into any ladders
This is my second motorcycle and the first time I've ever been on a Fender Eliminator Thank you again, HURRICANE, I got the sticker too! (Naps WebShop (angry) ) and put it on the back of the Upper CowlFront blinker ( Quantity:Pair (for Left and Right) ), it is Large change satisfaction in conjunction with Handlebar
Responses
Other reviews
good value for money
Material of Type using K-FACTORY's OEM License Lamp:I purchased this Eliminator to replace my Stainless Steel Fender Eliminator, which has a Stainless Steel base plate, black chrome plated and clear coated finish. I am satisfied with it because it is less expensive than other manufacturer's Fender Eliminator. In my case, I replaced the blinker with a POSH one, so it took time to adjust the angle and position of the blinker.
Of course, the accuracy was also fine. However, it would have been better if the bolts on the base plate were black instead of stainless steel.
View detail
I would have been fine with OEMFender...
When I went through the OEM Fender to get a belt to fix the Seat bag, I found that the OEM Fender was plastic (not weak, but it would flex), so I decided to use the Fender Eliminator Kit, which was also inexpensive.
Probably the most difficult part of the installation is the removal of the OEMFender.
Instruction Manual does not have instructions for removing OEMFender.
However, if you are a do-it-yourselfer, you can remove the Rear Fender when you insert the ETCCard, so you may not have to do so much work (^^;)
The construction itself is solid, so the seat bag can be securely fastened to the belt.
I feel like it could be a little more behind the License Plate, but I am satisfied with the strength of the product.
View detail
On the GSR750
I chose this product because I like the clean Rear view. I like that it is not cluttered, but it may feel cheap to some people.
The process was easy and uneventful.
The LED Lamp is also beautiful, but the projection to attach the Lamp is a little too large.
If we drive long distances in the rain or on roads with floating dirt, our rear bags and backs will get dirty, but this is unavoidable.
The price is low and it is a good product!
View detail
Refreshing with Slim design
I bought it because I wanted it to look Refreshing and Sexy from the back.
I am quite satisfied with the design, which is slimmer than other products.
I think most of the other companies' products are a little more blobby.
With this product, it seems as if it is integrated with Cowl.
The Instruction Manual was easy to understand and the DIY installation was a breeze.
View detail
Fender Eliminator Kit
It arrived earlier than I expected, which was a big help. The instruction manual for installation is difficult to read … I thought it would be better to make it a little larger. I am very happy with the quality of the product and the price. View detail