Reviews
Conti II type can be NORMAL.
The OEMHandlebar is so large that if it is replaced with a narrower one, the OEM will have a little extra space.
However, it could be left as OEM, but it interfered with the RadiatorRight Side surface.
It is a product that is better to have than not to have.
View detail
Bar handle has
I used to use 10cm Long on my HURRICANE Pipe Handlebar Kit, but it was too long, so I decided to use 5cm.
Clearance is just fine.
View detail
Fits: YAMAHA XJR400R, YAMAHA XJR400, YAMAHA V-MAX 1200, YAMAHA SRV250, YAMAHA SR400, YAMAHA FZR400, SUZUKI GSF1200, KAWASAKI ZR-7/S, HONDA Monkey BAJA, SUZUKI GSF750, YAMAHA XJR400, YAMAHA XJR1300, YAMAHA XJR1200R, YAMAHA XJR1200, YAMAHA SRX600, YAMAHA SRX400, YAMAHA SRX400, YAMAHA FZR250R, YAMAHA FZ400, SUZUKI BANDIT400
HURRICANE triangular table spindle nut
Exquisite workmanship, cheap price, good materials, beautiful colors, very accurate size, easy to install, and fits perfectly in the car View detail
took a chance and it payed off
Snapped the original cable. Ordered the short cable for the standard Z900RS after fitting lower bars. Worked out within 10-15mm of the Z900RS Cafe OEM cable length. Great fit. Fast shipping as always. View detail
I was satisfied with the 3cm but Large change
After purchasing the Motorcycle, the seating position was not quite right and I had back pain after running for a little while. View detail
Fits: KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR750 RS, KAWASAKI ZEPHYRX
HURRICANE 10cmLong throttle cable
Long cable was replaced when the handlebar was replaced.
Handlebar is HURRICANE's POLICE2 type with 27mm up set up holder compared to NORMAL.
OEMCable was not enough, so we decided to use a 10 cm long cable.
I think it fits nicely without being too long.
The replacement was done by one person, without removing the carburetor, so it took more than 30 minutes to hook up the new roll of Cable,
The return Cable did not take that long, but it was a struggle.
View detail
Fits: YAMAHA XJR400, YAMAHA XJR400R, YAMAHA XJR400R II, YAMAHA XJR400S
I'm lighter
Clutch is now lighter.
Stainless mesh, so it seems to be durable.
View detail
Diversion to CB250F
I installed a ZETA handlebar on my MC43, and it was about 30mm higher, but the OEM tension was too tight, so I replaced it with a ZETA handlebar. 1 pc of pull was applied to the handlebar, and the direct feel was increased by adjusting the play and the handle.:Pair (for Left and Right) I let it have play at full lock. View detail
Fits: YAMAHA XJR400, YAMAHA XJR400R, YAMAHA XJR400R II, YAMAHA XJR400S
Mesh
The mesh is durable and the Clutch is very light.
I would like to do this next time I replace it.
View detail
It can be installed with no problem if you have the tools.
As per your impresion, it takes a lot of time to remove the Screwwith Lock Bolt from the bottom.
Our procedure is to first remove the bolt that holds the clutch hose and brake hose to the body. The breaker bar is also large and sturdy. The Brake master and Clutch master can also be easily removed from the handlebar and placed on the body.
Once loosened somewhat, remove the 4 Bolts as the Ratchet of the FLEXHead can be easily turned afterwards.
Just float the Top Bridge and put the HURRICANE Spacer in between and put it back in place.
View detail
Fits: YAMAHA XJR1200, YAMAHA XJR1200R, YAMAHA XJR1300, SUZUKI INAZUMA400, SUZUKI INAZUMA1200(GSX1200FS), HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF
Handlebar cannot be installed without it.
I bought this Holder together with the Top Bridge for my ZZr Bar handle, and since the Top Bridge is also a HURRICANE, I was able to install it without any difficulty. I am satisfied with the position, not too far and not too close. View detail
Purchased this one due to bar handle change
Purchased this for my Pipe Handlebar conversion. The construction is good and I am satisfied. The installation itself is not difficult, but it is troublesome because it is necessary to completely close around the handlebar. If you do the other work together, you only need to do the whole rose once. View detail
Small size change, Large effect
[How is it used?
To change the position of DL1000 V-STROM650, which seems to fit but is slightly uncomfortable.
Was the one you received as per Image?
The quality is high, but the price is … hey?
Was the installation difficult?
If you can use hexagonal, it is easy.
How was your experience with it?
It is worth a try if you are feeling distant from Handlebar.
Fractional quantity without the need to replace cables:SetBack, but I could feel the effects.
Quantity, even with very cheap similar products from overseas companies.:I think the effect of the SetBack is the same, but it seems unlikely that there is a form that moves back without giving this height.
The other question is how much attention is paid to texture.
[Included Parts:were they on?
Bolt hole hidden Cap was included.
[Was there anything that disappointed you?
Why not make it a little more affordable?
View detail
Fits: SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER Big Boy, SUZUKI GRASS TRACKER Big Boy
GRASS TRACKER It was a long time for BIGBOY.
It was too long for GRASS TRACKER BIGBOY. We managed to get it to fit in the car by working out how to handle it.
Clutch has been revived.
View detail
Fits: KAWASAKI ZZR1200, KAWASAKI ZZR1200, KAWASAKI ZZR1100/ZX-11
Changed to Long cable due to change to Handlebar Up Type.
I changed to a long cable because I changed to a Handlebar Up Type. It is a little bit long, but it works fine. View detail
It was a little long.
Changed to Long cable due to change to Handlebar Up Type. It is a little long, but there is no problem in use. Conversely, the Handlebar can still be raised.
Installation was troublesome with the carburetor part.
View detail
Top Bridge has been changed to One point.
I replaced the handlebar for my own satisfaction. I think it is a very satisfactory product, although it is a casual part because it is the place where it enters the medium eyes of the driver. View detail
it work very light and smooth
I bought Hurricane long throttle cable to replace the old on my Honda VFR800 VTEC 2003. Shipping time is a bit longer than 2 weeks after shipping. Hurricane throttle cable is Made in Japan, the cable is long enought to install on my bike, it work very light and smooth. View detail
Position Comfort
The Handlebar on the DL1000 V-STROM650 felt a little far away, so I installed it.
After installation, the handlebar became a little closer to the hand, which made positioning much easier and touring more comfortable.
Cable, etc., only needed a little band, bracket, etc., positioning.
View detail
good quality, perfect fit
Bought these for dragstar 1100 classic. The cables look to be of good quality and fit my bike perfectly. Don't forget to lube the cables before installing them on the bike. View detail