Reviews
I don't like the Round Type Mirror on the 2024GROM.
I purchased this product because I could not get used to the design of GROM's Round Type Mirror, which was apparently a reuse of the for MONKEY mirror.
I chose "Made by HURRICANE" because I thought it was better than the inferior "Large Land" products. The installation is not so difficult, but there is no instruction manual, and the package is not printed, so inexperienced users may have some trouble!
The design is good, but the Mirror angle has a small vertical adjustment range and requires fine adjustment at the Lever mounting point.
Somewhat disappointing in terms of product
View detail
Excellent product, very, very well made. Installing is not an easy job, but that's due to W800 mechanics
This is an excellent product. I am installing a plush comfort seat which is slightly higher, and with these bars the geometry is perfect for touring. Quality is top notch. Everything is very well made, everything fits and well thought through. I would not try to install it unless you are capable enough to build the bike ground up. On mine, tank and light had to come off on top of obvious cables, break lines, etc. 4 hour job easily. If you are anything less than a master, give it to your trusted mechanic and pay accordingly. In case of W800, it is just how the bike is laid out, not a a fault of this product. In fact, because of everything fits so well, Hurricane have made it as easy as at all possible for this Kawasaki. View detail
Conti II type can be NORMAL.
The OEMHandlebar is so large that if it is replaced with a narrower one, the OEM will have a little extra space.
However, it could be left as OEM, but it interfered with the RadiatorRight Side surface.
It is a product that is better to have than not to have.
View detail
Fits: HONDA CB1100, HONDA CB1300SUPER BOLDOR, HONDA FTR223, HONDA NC700X, HONDA MONKEY, KAWASAKI 250TR, KAWASAKI W400, SUZUKI RV200 VANVAN, SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER Big Boy, SUZUKI GRASS TRACKER Big Boy, YAMAHA TW200, YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW225E
Type 2 to Type 3
I was using a Police Type 2 and changed to a Type 3 to get a little more up.
The length of the wire was delicate and I had prepared a long wire, but it was better to use a narrower wire, so I was able to use an OEM wire.
I prepared another one and narrowed the width further to my liking at 655mm.
View detail
Bar handle has
I used to use 10cm Long on my HURRICANE Pipe Handlebar Kit, but it was too long, so I decided to use 5cm.
Clearance is just fine.
View detail
Replace OEMHandlebar
Separate Handlebars are too aggressive; Swallow handle is too short
Therefore, it becomes Condor Handle.
However, in the reverse position (where the Grip is lower than the Clamp), there is too little Clearance between the bar and the Blinker.
View detail
Fits: HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, KAWASAKI W400, KAWASAKI 250TR, HONDA MONKEY, HONDA MONKEY, HONDA HORNET250, HONDA NC700S, HONDA FTR223, HONDA FTR223, HONDA CB750, HONDA CB400SUPER BOLDOR, YAMAHA TW225E, YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW200, YAMAHA SR500, YAMAHA SR400
Best Match for Good Position XSR125.
The handlebar on my XSR125 did not fit and my shoulder stiffness got worse after the first ride, so I replaced it with this handlebar based on Net information.
I also bought a Flat continental2 type and compared it with the BMConti3 type while temporarily attaching it, and found that the BMConti3 type fit better.
It's so easy to ride that I think this should be the standard now! It is so easy to ride. I recommend it.
I had prepared a riser, but I am 175cm tall and it is just right without the riser.
Small patterned person is Quantity:SetBackRiser would be a good position.
Drilling is required, but a drill driver is sufficient for this purpose as long as the position is marked temporarily and the punch is firmly applied.
It is hang to go little by little while checking, not trying to open it all at once.
It was a good buy for the XSR125.
View detail
(Commuting) BattleMirror
I was concerned about the width of OEMMirror and purchased it. It is not only wide, but also tall, and is built as expected.
Compared to other products, the design is more OEM-like, so I think the balance with the overall body is good.
By the way, this is the second time I bought this because the one I bought before broke.
View detail
Fits: HONDA HORNET250, HONDA APE 50, HONDA APE 50, HONDA APE 100, HONDA VTR250, HONDA VTR250, HONDA NC700S, HONDA FTR223, KAWASAKI ZRX1100II, KAWASAKI ZRX1100, KAWASAKI W800, KAWASAKI W400, KAWASAKI ZEPHYR400, YAMAHA XJR400R, YAMAHA XJR1300, YAMAHA XJR1300, YAMAHA TW225E, YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW200
This is what it looks like when installed on a KTM 2013 DUKE.
This is what a BMConti2-type Handlebar looks like when attached to an Initial ModelDUKE. Finger is about the same height as Limit. View detail
Fits: YAMAHA XJR400R, YAMAHA XJR400, YAMAHA V-MAX 1200, YAMAHA SRV250, YAMAHA SR400, YAMAHA FZR400, SUZUKI GSF1200, KAWASAKI ZR-7/S, HONDA Monkey BAJA, SUZUKI GSF750, YAMAHA XJR400, YAMAHA XJR1300, YAMAHA XJR1200R, YAMAHA XJR1200, YAMAHA SRX600, YAMAHA SRX400, YAMAHA SRX400, YAMAHA FZR250R, YAMAHA FZ400, SUZUKI BANDIT400
HURRICANE triangular table spindle nut
Exquisite workmanship, cheap price, good materials, beautiful colors, very accurate size, easy to install, and fits perfectly in the car View detail
Good position
I came across this product after doing a lot of research on the height and width of the Japanese Vehicle Inspection Correspondence on the CB750rc42.
The width is the same and the height is about 35mm higher than the other two, so I asked the shop that installed it to check if they had done the same thing and since it was compliant, they installed it without refusal.
Extension Harness was also prepared in case, but it was used only for Blinker switchWiring extension.
For this level of uplift, it would have been more cost-effective to just extend the Blinker switchWiring than to purchase Extension Harness.
The position is only 35mm up, but it feels much higher, and the handlebar feels a little tighter in the front, so it is very easy to drive.
It is as easy as if it were a learner's car, but the system is also very windy as it approaches vertical.
I am self-satisfied, but it was a good decision to replace it because it is totally easy to drive and maintain a non-fatiguing position.
View detail
excellent quality
Extremely solid, well made bars. I have fitted inverted for a low clubman style. Works well in combination with the bar end mirors and SSK adjustable levers. View detail
took a chance and it payed off
Snapped the original cable. Ordered the short cable for the standard Z900RS after fitting lower bars. Worked out within 10-15mm of the Z900RS Cafe OEM cable length. Great fit. Fast shipping as always. View detail
Fits: SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER Big Boy, SUZUKI GRASS TRACKER, SUZUKI GSX400, SUZUKI ST250 E Type, SUZUKI ST250, SUZUKI RV200 VANVAN, KAWASAKI BALIUS2, SUZUKI GSR400, KAWASAKI ZEPHYRX, KAWASAKI ZEPHYR750 RS, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR1100 RS, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR1100, KAWASAKI ESTRELLARSCustom, KAWASAKI ZRX400, KAWASAKI ZRX400II, KAWASAKI ZRX1200R, KAWASAKI ZrX1200ZrX1200 DAEG
Used for ST250
Used for ST250.
We were happy to be able to use the Wires as they were.
View detail
It's best.
Transforms into a classic look.
The driving position is very comfortable and stable.
Even if you drive for a long time, it will not put any strain on your body.
Handle replacement can be done quickly if you purchase the Hurricane extension harness together.
This is one of the customizations I am most satisfied with. -------------------------------------------------- -------- Transforms into a classic look. The driving position is very comfortable and stable. Even if you drive for a long time, it will not put any strain on your body. Handle replacement can be done quickly if you purchase the Hurricane extension harness together. This is one of the customizations I am most satisfied with. Powered by Google Translator
View detail
I was satisfied with the 3cm but Large change
After purchasing the Motorcycle, the seating position was not quite right and I had back pain after running for a little while. View detail
Normal good
Narrower and lower than OEM, recommended for those who do not want to use Separate handle.
However, I don't like the fact that the holes have to be increased to make the desired position due to the holes being machined.
I want it to be without Hole.
View detail
Fits: KAWASAKI ESTRELLARSCustom, KAWASAKI ZRX1200R, KAWASAKI ZRX1100II, KAWASAKI ZRX1100, KAWASAKI W400, HONDA MONKEY, HONDA APE 50, HONDA APE 50, HONDA APE 100, HONDA NC700X, HONDA FTR223, HONDA FTR223, HONDA CB750, HONDA CB400SS, HONDA CB1300SUPER BOLDOR, HONDA MONKEY, KAWASAKI BALIUS2, KAWASAKI ZEPHYR1100 RS, KAWASAKI ZEPHYR1100, HONDA CB1100
I installed it on a 250tr.
I installed this on my 250tr. I was bored with the OEM so I took a shot at it as an amateur. I was nervous about drilling the holes, but it turned out well. I am looking forward to touring. I am looking forward to touring. View detail
usually
Installed on HURRICANE's Duralumin Pipe Handlebar.
It is a very ordinary Bar end cap, but I think it is a nice slit in it.
Rubbers for inner diameters from 14mm and 18mm are included.
View detail
Fits: KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR750 RS, KAWASAKI ZEPHYRX
HURRICANE 10cmLong throttle cable
Long cable was replaced when the handlebar was replaced.
Handlebar is HURRICANE's POLICE2 type with 27mm up set up holder compared to NORMAL.
OEMCable was not enough, so we decided to use a 10 cm long cable.
I think it fits nicely without being too long.
The replacement was done by one person, without removing the carburetor, so it took more than 30 minutes to hook up the new roll of Cable,
The return Cable did not take that long, but it was a struggle.
View detail