Reviews
High gear conversion of ADV150
The ADV150's Pulley boss is 49mm and my PCX150 (KF18) is 47.5mm.
There is no ADV150 High speedPulley at the moment, so the only way to increase the maximum speed is to adjust it with the Pulley boss.
In the NORMAL state of ADV150, the limiter is activated when the meter reading is about 115 km/h. At the very least, the meter reading should be set to 120 km/h. I would like to increase the Meter reading to at least 120km/h.
I would like to change to Pulley boss for PCX150 and adjust it with Shim.
I put in 1mm Shim and it was 119km/h. This time I bought 0.3mm and 0.5mm and made it 48.3mm.
As expected, the speed was 121 km/h (Meter reading), but the Belt moves to the outermost edge of the Pulley, so it is safe to assume that the Belt will be
I think the best condition is with 1mm Shim in place (Normal 0.5mm).
*This is a spec. that is outside the manufacturer's expectations. Please try it at your own risk.
View detail
High gear conversion of ADV150
The ADV150's Pulley boss is 49mm and my PCX150 (KF18) is 47.5mm.
There is no ADV150 High speedPulley at the moment, so the only way to increase the maximum speed is to adjust it with the Pulley boss.
In the NORMAL state of ADV150, the limiter is activated when the meter reading is about 115 km/h. At the very least, the meter reading should be set to 120 km/h. I would like to increase the Meter reading to at least 120km/h.
I would like to change to Pulley boss for PCX150 and adjust it with Shim.
I put in 1mm Shim and it was 119km/h. This time I bought 0.3mm and 0.5mm and made it 48.3mm.
The speed was 121 km/h (Meter reading) as planned, but we will BeltGuide to the outermost edge of Pulley to be safe.
I think the best condition is with 1mm Shim in place (Normal 0.5mm).
*This is a spec. that is outside the manufacturer's expectations. Please try it at your own risk.
View detail
Harness tape if you do electrical work
I used to think Vinyl Tape was fine.
However, Vinyl tape can become sticky over time, so it is better to use a proper harness tape, even though it costs a little more.
Harness tape from KITACO, so far without any problems.
We'll see what happens when we remove the Tape in a few years!
View detail
Used for fixing Carrier and Mounting Base without modification
The CB400SF is equipped with DAYTONA's Multi Wing Carrier, which is used as a bracket to fix the Carrier and the mounting base.
As a result, I am satisfied with the normal use of the product.
However, similar products are sometimes cheaper to buy at Home center.
It's Stainless, so I hope it won't rust (laughs).
View detail
Rear Fender SPLCowl and as a Spacer between them
The accuracy of the A-TECH Rear Fender SPL was not good, so I had to bite the Spacer between the body and cowl sides. Initially, I had multiple layers of Large Thread Nut and Stainless washers on hand, but I didn't want to crack them because they were too hard to hit, so I used Nylon. View detail
MONKEYTop bridge
Used for the bolt of MONKEYTop bridge. This is definitely usable. View detail
simple
[How is it used?
TZr250R (3XV) The cap attached to the Negative Pressure Nipple on the front bank side carburetor of the "M" was cracked due to aging, so I purchased this cap as a for replacement.
OEM Parts would have been fine, but 1pc.715 yen. (as of July 2022) I was looking for a replacement for a rather good price, and I found this product.
Was the one you received as per Image?
As explained, the Quantity:It arrived in 1 Set of 2pcs.
How was your experience with it?
I measured the inner diameter of the original cap and found it to be about 4mm, so I purchased one with an inner diameter of 3.8mm.
I just replaced it and so far, no problems at all.
It was too long as it was, so I cut it, but I cut it a little too much. (Lol)
It is available in a wide range of sizes, is inexpensive, and can be used in a variety of ways.
[Points to note]
The wide range of sizes available means that you need to select the size that best fits your application.
Well, it's cheap, so if it's a pain in the ass, you can buy a Size before and after the objective, too.
【Review】
I am very happy with the product, which is inexpensive and serves its purpose.
Thanks to this, we didn't have to buy OEM parts that cost a fortune.
View detail
TZr250R (3XV) Used for
[How is it used?
TZr250R (3XV) The Bolt was also renewed in conjunction with the replacement of the Rear Brake Disc Rotor on the
OEM would have been fine, but 1 pc385 yen (as of July 2022) I chose this product because it is inexpensive and can be made of Stainless Steel.
Was the one you received as per Image?
I was a little worried about whether the length would be the same since the fit was universal, but it was the same length as the OEM.
Was the installation difficult?
It is not so difficult as long as you are careful not to lick the originally attached Bolt when you remove it.
Screw lock agent needs to be applied, so that needs to be prepared separately as well.
How was your experience with it?
I can't say for sure since it is still so soon after the replacement, but it feels good to have a new Bolt.
Naturally, Bolt's Size and accuracy aspects are perfectly acceptable.
There is a possibility of licking it when removing it, but I think it would be better to use Screw Mole for that.
【Review】
Compared to the OEM bolt, it is less expensive and can be converted to a Stainless bolt, killing two birds with one stone.
Front is also scheduled to be replaced in the future, so Quantity:I purchased 1 Set of 10pcs. but TZr is only 3pcs. to be used in Rear, so I think I should just buy it in Rose.
View detail
If it says from [[in play part 2]] conclusion, the products here will be the highest products in general!! The aluminum spacer collar here is inside diameter:phi8.2mm. Outside diameter: phi20mm Height: It becomes a 30-mm product. If existence of W
If it says from [[in play part 2]] conclusion, the products here will be the highest products in general!!
The aluminum spacer collar here is inside diameter:phi8.2mm. Outside diameter: phi20mm Height: It becomes a 30-mm product.
If existence of Webike is not known Didn't it meet with the aluminum spacer collar made from a kitaco, and the vivid bolt?,
.
.
By Webike, customization filled to originality and creativity can be performed, and it is a delightful limitation!! An attached image,
The muffler made from p's supply is treated to the address V125, and it is a chamber protector made from burial. (tune by a moriwaki sticker and #OS800-30000-41!!) In order to equip,
They are contents which use the aluminum spacer collar made from a kitaco and vivid bolt which are the products chosen as the end of deliberation.
The spacer collar made from a product chamber protector made from burial 竊?kitaco.
(#0900-093-00060, inside diameter phi8.2mm, outside-diameter phi20mm, and 30 mm in height) The engine side of the product muffler made from product muffler made from 竊?p's supply attached aluminum billet plate 竊?p's supply attached M8 aluminum-collar (outside-diameter phi20 mm and, and 14 mm in height) 竊?address V125.
A muffler mount and M8 female-screw partial we the bolt used of this customization,
- vivid bolt made from a kitaco of M8x100 (#0900-080-0015) was chosen!! [ -- [refer to [ the in play part 1 ]] ], if two or more sets of the addresses V125 which drive the inside of a town are seen,
It seems that its respectively different customization was given and each loves the address V125 colored with personality.
Moreover, is conversion of a muffler mentioned the common feature of customization of the address V125?
.
.
If it equips with the chamber protector made from burial, how is it as a protector to the replace muffler which you chose (the outside diameter of a white duracon resin part is phi36mm.)?
The size of the sticker of a moriwaki is about 56 mm.
Since the outer circumference of a duracon part is about 113 mm, the sticker of a moriwaki is a size like the semicircle.
it is just a sticker tune of a just size!! Replace muffler of the address V125 which we incidentally cannot but praise, steiner muffler made from p's supply it is -- TSU!!
View detail
It is perfect!!
It is perfect!! View detail
The product of a kitaco is TSU which is only a product saved cheaply and joyfully!! Custom-made plan of the blinker of W650. (The 1) TSU which is appropriation wearing about the blinker of 250TR W650!! First of all, it is exchange about the conclusion
The product of a kitaco is TSU which is only a product saved cheaply and joyfully!! Custom-made plan of the blinker of W650.
(The 1) TSU which is appropriation wearing about the blinker of 250TR W650!! First of all, it is exchange about the conclusion screw of the blinker lens of 250TR.
Since an authentic positive one is iron and it is easy to rust, parts are replaced to the tapping screw made from a stainless!! YO from which the tapping screw for the pure blinkers of a zephyr system or a vulcan system is incidentally also set to M4x25.
We did two-piece (a total of 8) acquisition of the product here, and were taken as the screw of the blinker lens of order.
*) -- The stock case of W650 becomes the relay of 12V/15W.
Relay exchange becomes indispensable when diverting the blinker of other vehicles to W650.
Relay #27002-1101 for 12V/21W (product blinker conversion-code made from posh is followed.) = Kawasaki original manufacturer's product
.
.)
View detail
Cowl scratch prevention
I was concerned about Bolt tightening directly on Cowl and installed it.
This is a relief.
I think it would be easier to use if it were thinner and translucent.
View detail
Say goodbye to stacked Washers!
Used to install Cowl Bracket on Zr-7S.
I bought it to install Bracketetetc. to Beauty, which is not adding up as I customize it.
In the temporary installation, I had stacked the Washer for M8 Bolt for now, but it was not beautiful and not good for my mental health, so I decided to use a proper color.
It is beautifully machined and anodized, so it is hard to corrode.
Various sizes and colors are available from various companies, so it is helpful to be able to choose according to the dimensions and colors you want to use.
This time, I was looking for something with a less large outer diameter, so it was a great help.
View detail
A lifesaver in times of trouble!
[How is it used?
During a month-long long-distance touring with FZS600, one of the bolts holding the RightFootpeg Plate fell off or was lost while driving about 2000 km after departure (tears). It was a holiday weekend in May, and all the motorcycle shops were closed, so I was at a loss. In the shelves, I found the Bolt I was looking for! Cap Bolt with FlangeM8x20 P1.25 The M8 Bolt was sitting in a brilliant halo (our Image)! I felt as if I had used up all the luck in my life at that time. (Laughs) Home center also sells M8 Bolt, but most large ones are P1.5, and P1.25, which is often used for motorcycles, is rarely sold.
Was the installation difficult?
The kind and beautiful lady clerk at 2 Rinkan (our Image) lent me a tool and I was able to install it quickly and easily.
How was your experience with it?
It's the same Bolt as the OEM, so nothing has changed, but it has filled my heart! (LOL)
[Was there anything that disappointed you?
There's not a ton of demonstration that I'm not disappointed! I can't sleep with my feet facing 2 Rinkan and KITACO anymore! (LOL)
Other items that would be helpful
Opinions and requests for Manufacturer:KITACO! Thanks for all your help! And 2 Rinkan too! (Sorry, Mr. We-Big!)
View detail
Convenient
I have not been able to use the helmet holders on the body of the vehicle, which are usually large and hanging, and until recently I have been using a small wire lock or a Dial-type carabiner with a 40cm-plus wire threaded through it. I was not interested in using the Helmet holder on the body of the car.
However, I was still searching for something easier and found this product.
The combination of this product and a 100-yen Dial lock makes it compact enough to fit in a pocket, making it convenient to carry.
It is too thin and unreliable for theft prevention, but it is a hell of a lot better than just hooking it to Mirror or the like.
View detail
There is no problem
It is a good product in general, and I chose it because I imagined it would be more resistant to deterioration over time than the White color. View detail
It is stiff and helpful.
Since the clutch lever, wire, and routing, etc., have been replaced, it may be that the mounting points are subjected to forces in odd directions, or it may be that the quantity has already been reduced.:2pc. Set ruined.
The clutch can be cut without it, but it is smoother with this cover. As other reviewers have mentioned, if the installation method is correct, there is a little bit of hang.
I have one squishy one a year, but I always Stock it because of the price. I really appreciate the fact that you can provide these parts.
View detail
Used to install Engine protector.
[How is it used?
We chose KITACO products because they are reliable and must be sturdy since they will be used to install Engine protector.
Was the one you received as per Image?
Material is Aluminum A2017-T4 cut-out with Black Anodized Finishing.
How was your experience with it?
I haven't tipped it over yet, so I haven't been able to check its strength, but it will probably be Large sturdy w
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Points and hang of installation:Since the engine mount is used for installation, Screw lock fluid was used to prevent the bolt from loosening.
Availability of Instruction Manual:No Instruction Manual.
View detail
I should have used this.
When I used the Extension Bracket to adjust the angle of the Fender Eliminator, it was too long and I couldn't set the angle as it was, so I used it to fine tune the angle and it looked like a reflection. View detail
Is good
Since we forget when we replaced the Oil, it helps us to manage it because we can see at a glance the date and distance of the replacement.
Since it is not a Type Seal that leaves adhesive residue, it is convenient because it can be easily reapplied anywhere.
View detail