Reviews
Universal and can be used in many ways
[How is it used?
The bar of the external Rear Sets was not long enough, so we put it on to extend the length.
I personally prefer longer ones because they are easier to load.
Was the one you received as per Image?
As per Image
Was the installation difficult?
It is easy to insert between Footpeg and Footpeg Plate.
How was your experience with it?
It serves its purpose because it is used as a simple color.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
It's just a color of Aluminum, so it could be a little cheaper. I thought it was a good idea.
but it is good to have a variety of Sizes to choose from.
View detail
Used to reduce rattling of Brake lever
[How is it used?
Brake lever was rattling badly and I bought it in hopes that it would get better.
The Touch feeling of the MASTER itself was not so good, but I suspected that maybe it was because the rattling was so bad that I could not press the Piston straight? I also suspected that it might be because I could not press the Piston straight.
To be honest, since it is a SmallEngine Displacement Volume for a foreign car, I thought that the rattling might be terrible combined with poor accuracy, but I tried it when I learned from an article on Webig that this Washer can reduce the rattling.
Was the one you received as per Image?
As you can see in the picture, it is just a Washer.
It is not a very expensive product, but the price of this thin Washer may be too expensive for some people...
Was the installation difficult?
Simply remove the Brake lever and insert it in between.
Washer is just on Lever, so it is a bit frustrating to have to Gap it back to MASTER.
How was your experience with it?
Actually, I first tried 0.3mm, but did not feel much change. 0.6mm with 2 layers of 0.3mm reduced rattling in a good way. However, I felt that the movement of Lever was a little reluctant or stuck, perhaps due to the two layers of 0.3mm, and I felt it was dangerous.:I settled on 1pc. Even with 0.5mm, there is some rattling, but it has been reduced to an acceptable level.
However, I did not see any large change in the touch feeling that I had expected, and I felt again that in such a case, I had no choice but to replace the entire MASTER.
[Included Parts:were they on?
Washer only.
[Was there anything that disappointed you?
nothing special
View detail
To M8 with M10 color
I wanted to use the Exclusive Aluminum Spacer for M10 Screw Collar from the same K-CONBrand with M8 Bolt.
These itchy parts are very helpful.
Surprisingly, there are no conversion parts like this.
View detail
Lineup of other materials would be better.
I purchased this spacer to connect the shift arm to the GEARShiftClamp when installing an external footpeg kit on my NSR250R MC21. I really wanted a Brass spacer, but they didn't have any, so I went with an Aluminum spacer. View detail
Good product
I used it to adjust the Exhaust Band fixation.
As a Spacer, it is neither good nor bad.
The sale of Small portions is very helpful.
View detail
It's easy to choose.
These colors are hard to find at Home Center, but
With the K-CON KITACOConvenienceParts Aluminum spacer, it's easy to choose your size.
It would be great to have everything in stock.
View detail
Thanks for your help.
Spacer is the only choice for K-Con.
With a wide range of Lineup, you can choose as many as you want.
If I had a little more stock, I would buy it at Timing, which I want, but sometimes I don't have it.
Stock.
View detail
Size Purchase to align
Eventually I do not use this Size. However, I think that there are things to use in the future. It is a product that makes sense to keep it as it is used with subtle adjustments. View detail
Multiple Size Spacer is required
There is meaning in having several pieces. Because it is better to arrange them all in the same way as carburetor 's Jet in order to adjust when the Size does not match delicately. View detail
KL 250 Sherpa's Rear brake reservoir for fine adjustment of tank position
【What made you decide the purchase?】
In SUPER SHERPA, Rear brake reservoir Tank is close to Exhaust pipe, Diaphragm heat, Diaphragm reservoir tank deforms and there is a chronic disease where Fluid leaks.
Although countermeasures are available from Manufacturer, in order to reduce the influence of heat even a little, buy this product to keep the position from the Exhaust pipe away.
【How was it actually used?】
It is an ordinary M6 Spacer with an outer diameter of 18 mm and a thickness of 5 mm.
However, because there are not so many Spacers of Size like this, I appreciate KITACO who lineup many products that can reach itchy places.
【Mounting was difficult?】
It is easy because it just removes Screw of M6.
【Please tell me the installation point and hang】
Be careful not to skew the reservoir tank when removing the Screw stopping the reservoir Tank because air may get mixed in.
[Is there anything I was disappointed about?]
It was possible to keep it away from the Exhaust pipe by 5 mm and I felt that I fulfilled the goal! Hey, Hose interfered with Frame.
Although it seemed not to be pressed strongly, since it is possible that Hose may hurt due to vibrations etc. I removed it crying.
I wonder if it was 3 mm?
【Hope for Manufacturer - Please let me know if you have any improvement points]
None
【Have you compared items?】
None
[Others]
Frequently check the reservoir Tank and if there is any abnormality in appearance it is only necessary to exchange...
View detail
Caliper support and Caliper Clearance secured
When Caliper was installed in Caliper support made by One-off, Caliper and Support interfere somewhat and it was not able to install properly. As a result, we purchased 2 mm of Color, and it was possible to install it securely and without interfering.
Webike is very convenient because Small items such as Bolt and Color can be ordered easily without hesitation.
View detail
It was used for attachment of the Screen considered to be an external article MT-01. Since there is a kind with a splendid diameter of inside and outside, a just right Size should be found generally. Probably, finishing will be reasonably p
It was used for attachment of the Screen considered to be an external article MT-01.
Since there is a kind with a splendid diameter of
inside and outside, a just right Size should be found generally.
Probably,
finishing will be reasonably priced.
It is the highest if there is
Color-alumite specification.
View detail
It used in order to make the old type disk rotor of SR400 into flange bolt & wire lock specification. If there is this [ no ], the outer circumference of a flange will not be hit and fastened on the edge of a hub. Therefore, it is that of ! regard
It used in order to make the old type disk rotor of SR400 into flange bolt & wire lock specification.
If there is this [ no ], the outer circumference of a flange will not be hit and fastened on the edge of a hub.
Therefore, it is that of ! regarded as one-piece 200 yen over being high but although appreciated very much, and is three.
View detail
Since a disk rotor did not come to the center of the caliper bracket, it equipped. It is the left when the right will be approached if you have no spacer, and it is a washer of a home center. It was exact at a 0.5-mm spacer.
Since a disk rotor did not come to the center of the caliper bracket, it equipped.
It is the left when the right will be approached if you have no spacer, and it is a washer of a home center.
It was exact at a 0.5-mm spacer.
View detail
When attaching the sub frame made from KITACO to the zoomer (ruckus) of carburetor specification, this color is required in order to bury it, since a crevice is made. Although it thinks that color purchases because it is required, it sticks from the b
When attaching the sub frame made from KITACO to the zoomer (ruckus) of carburetor specification, this color is required in order to bury it, since a crevice is made.
Although it thinks that color purchases because it is required, it sticks from the beginning, and should be a little cheap just, I think that it is a good place that can buy it afterwards when it loses.
View detail