Reviews
Rear Fender SPLCowl and as a Spacer between them
The accuracy of the A-TECH Rear Fender SPL was not good, so I had to bite the Spacer between the body and cowl sides. Initially, I had multiple layers of Large Thread Nut and Stainless washers on hand, but I didn't want to crack them because they were too hard to hit, so I used Nylon. View detail
Fixing Screw section.
Flat washers are also made of stainless steel to prevent scratches and loosening. View detail
Stainless Steel
In order to use stainless steel bolts to prevent rust when fixing the parts, this washer is used to prevent loosening. View detail
If it says from [[in play part 2]] conclusion, the products here will be the highest products in general!! The aluminum spacer collar here is inside diameter:phi8.2mm. Outside diameter: phi20mm Height: It becomes a 30-mm product. If existence of W
If it says from [[in play part 2]] conclusion, the products here will be the highest products in general!!
The aluminum spacer collar here is inside diameter:phi8.2mm. Outside diameter: phi20mm Height: It becomes a 30-mm product.
If existence of Webike is not known Didn't it meet with the aluminum spacer collar made from a kitaco, and the vivid bolt?,
.
.
By Webike, customization filled to originality and creativity can be performed, and it is a delightful limitation!! An attached image,
The muffler made from p's supply is treated to the address V125, and it is a chamber protector made from burial. (tune by a moriwaki sticker and #OS800-30000-41!!) In order to equip,
They are contents which use the aluminum spacer collar made from a kitaco and vivid bolt which are the products chosen as the end of deliberation.
The spacer collar made from a product chamber protector made from burial 竊?kitaco.
(#0900-093-00060, inside diameter phi8.2mm, outside-diameter phi20mm, and 30 mm in height) The engine side of the product muffler made from product muffler made from 竊?p's supply attached aluminum billet plate 竊?p's supply attached M8 aluminum-collar (outside-diameter phi20 mm and, and 14 mm in height) 竊?address V125.
A muffler mount and M8 female-screw partial we the bolt used of this customization,
- vivid bolt made from a kitaco of M8x100 (#0900-080-0015) was chosen!! [ -- [refer to [ the in play part 1 ]] ], if two or more sets of the addresses V125 which drive the inside of a town are seen,
It seems that its respectively different customization was given and each loves the address V125 colored with personality.
Moreover, is conversion of a muffler mentioned the common feature of customization of the address V125?
.
.
If it equips with the chamber protector made from burial, how is it as a protector to the replace muffler which you chose (the outside diameter of a white duracon resin part is phi36mm.)?
The size of the sticker of a moriwaki is about 56 mm.
Since the outer circumference of a duracon part is about 113 mm, the sticker of a moriwaki is a size like the semicircle.
it is just a sticker tune of a just size!! Replace muffler of the address V125 which we incidentally cannot but praise, steiner muffler made from p's supply it is -- TSU!!
View detail
It is perfect!!
It is perfect!! View detail
Cowl scratch prevention
I was concerned about Bolt tightening directly on Cowl and installed it.
This is a relief.
I think it would be easier to use if it were thinner and translucent.
View detail
Say goodbye to stacked Washers!
Used to install Cowl Bracket on Zr-7S.
I bought it to install Bracketetetc. to Beauty, which is not adding up as I customize it.
In the temporary installation, I had stacked the Washer for M8 Bolt for now, but it was not beautiful and not good for my mental health, so I decided to use a proper color.
It is beautifully machined and anodized, so it is hard to corrode.
Various sizes and colors are available from various companies, so it is helpful to be able to choose according to the dimensions and colors you want to use.
This time, I was looking for something with a less large outer diameter, so it was a great help.
View detail
Lineup of other materials would be better.
I purchased this spacer to connect the shift arm to the GEARShiftClamp when installing an external footpeg kit on my NSR250R MC21. I really wanted a Brass spacer, but they didn't have any, so I went with an Aluminum spacer. View detail
Used to install Engine protector.
[How is it used?
We chose KITACO products because they are reliable and must be sturdy since they will be used to install Engine protector.
Was the one you received as per Image?
Material is Aluminum A2017-T4 cut-out with Black Anodized Finishing.
How was your experience with it?
I haven't tipped it over yet, so I haven't been able to check its strength, but it will probably be Large sturdy w
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Points and hang of installation:Since the engine mount is used for installation, Screw lock fluid was used to prevent the bolt from loosening.
Availability of Instruction Manual:No Instruction Manual.
View detail
Outer Diameter Size is helpful
I have purchased a different size before, but this time I needed something other than the one for my motorcycle and was looking for something with an outside diameter of 25mm or more and an inside diameter of 10mm, so I was very pleased with your help.
I see that they are available in a variety of thicknesses. It would be great if they were a little cheaper, but …
View detail
I should have used this.
When I used the Extension Bracket to adjust the angle of the Fender Eliminator, it was too long and I couldn't set the angle as it was, so I used it to fine tune the angle and it looked like a reflection. View detail
Is good
Since we forget when we replaced the Oil, it helps us to manage it because we can see at a glance the date and distance of the replacement.
Since it is not a Type Seal that leaves adhesive residue, it is convenient because it can be easily reapplied anywhere.
View detail
prevention of slackening
Lock nut to prevent loosening.
I am relieved to know that this will not loosen easily.
View detail
It worked for Cowl's Chatter and others.
This product is inexpensive, but it has worked well with Replacing Screw on Cowl's Chatter and other products. Now all I can hope for is durability! View detail
It can be easily customized by simply covering it.
This product can be easily customized by simply placing it over an existing bolt. It can be used to hide rusted screws or as a Simple Waterproof alternative! View detail
justification
Used for adjusting the position of the Rear Sets and for fixing Spacer.
The size and thickness choices and reasonable price are very helpful.
View detail
Used for SilencerOffset
[How is it used?
When I installed RSV's Silencer on D Tracker, the exhaust was interfering with the License Plate and making a strange noise, and the exhaust was making the License Plate dirty.
Was the one you received as per Image?
It is an Aluminum tube as you see it.
Was the installation difficult?
Basically, I just put the Spacer between the Silencer Bracket, but I need to get the balance for offset on the entire exhaust pipe, so I need to make sure that the Bolt and Nut of each joint of the exhaust pipe, including the Cylinder attachment part of the exhaust pipe, are in place once. The silencer was lightly loosened, and the silencer was offset 20mm outside the vehicle body to prevent excessive force from being applied to a single point.
How was your experience with it?
As expected, the exhaust interference was eliminated, the noise disappeared, and the License Plate was no longer dirty.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
KITACO's ConveniencePartsSeries is very useful, but a lower price would be helpful.
Other items that would be helpful
Point or hang of installation:If you try to offset the silencer part alone, excessive force will be applied to a single point, leading to damage in the long run.
View detail
Suspension conversion
Bolt size conversion don't cheap Iron View detail
Thickness Size is abundant and ○
I purchased this product to adjust the position of the Bolt where the Exhaust System is installed.
The surface finish of aluminum is worse than that of Posh, but the outer diameter is slightly larger. (Posh21.6 KITACO22.0)
The variety of sizes is also very helpful because you can choose according to your needs.
View detail
Thin type
I purchased this low profile lock nut because the length of the bolt to which the Exhaust System is attached was too long for the normal thickness lock nut to fit over the Limit Screw.
Thanks to this, I was able to tighten it without any problem and I am satisfied.
View detail