Reviews
Fits: KAWASAKI ZX-6R, KAWASAKI ZRX1200DAEG, KAWASAKI Z250, KAWASAKI Z1000 (water-cooled), KAWASAKI Ninja400R, KAWASAKI Ninja250, KAWASAKI Ninja1000
For your first Custom! Made in Taiwan! No visibility problems!
There is no difference between this product and the OEM Product except for the color. I did not feel any impression of poor workmanship.
The Blinker's visibility is not reduced during the daytime, and it successfully combines practicality and good looks!
View detail
I wanted to install Inch bar.
[How is it used?
I wanted to install a Taper Handlebar (Inch bar? Fat bar?) which was popular at that time on my DJEBEL250XC. When I was looking for a compatible clamp to install on my DJEBEL250XC, I purchased this product made by JILLS, which was the cheapest product I could find at the time.
Was the one you received as per Image?
As a novice mountaineer, I was used to seeing a regular handlebar of 22mm, but the thicker handlebar of 28.5mm was a new experience for me. The Real Racer." It looked very Parenthesis-like.
natural The "two bites." Therefore, I did not think about the Merit of Millibar or the Demerit of Inch bar, but focused on the good appearance of Parenthesis and kept on going.
The Handlebar Clamp, which allows the Inch bar to be mounted, was just as Image described.
How did it compare to other products?
I have never purchased a clamp for Inch bar conversion other than this product, so I cannot compare them, but I have never had any trouble using JILLS clamps, so this was the best product I purchased to achieve my goal because it was not bad looking and had no trouble at this price. I think it is the best product I have purchased for the purpose.
[Points to note]
The OEM Handlebar Clamp was designed for a 22mm diameter handlebar, but the OEM Handlebar Clamp is thicker than the OEM Handlebar Clamp, so the mounting position is inevitably higher than the OEM Handlebar Clamp.
If you do not like the Up position, please purchase a Low position type Inch bar or make the final height adjustment on the Handlebar.
[Included Parts:were they on?
Quantity on the underside of OEM's Clamp:The lower Clamp and upper Clamp of the for inch bar to be set is Quantity:Set, 4 Bolts to fix the lower Clamp of OEM and the lower Clamp of Inch bar, and 4 Bolts to fix the Inch bar are Quantity:Set
[Was there anything that disappointed you?
I have no complaints about the product itself and the Color variations. "Silver" "Black" "Red" The three colors are available in the following three colors
If I may be so extravagant, it would be nice if you could add more color variations, but if the cost increases as a result, I'm fine with keeping the colors and price at the current level.
0Other items that may be useful include
Point and hang of installation
There are no points or hangetc. on the clamp side, and it is better to pay attention to the positioning of the Handlebar or Guard & Lever to be installed.
Please make sure to check the optimal handlebar installation angle & compromise position of both Levers and Guards during various movement positions such as normal sitting, standing, back load riding with the hips pulled back, front load riding, etc., and make sure to fix this fixation.
[ITEMS TO BUY TOGETHER
Since you will be using this product, it is essential to purchase an InchBar type handlebar with a shape that matches your Riding position as mentioned above.
If you can afford it, you should also purchase peripheral parts such as grips, hand guards, short type brake and clutch leveret, etc. that suit your taste.
[Opinions and requests to Manufacturer
Thank you for responding to these niche demands, and please keep up the good work.
View detail
Fits: HONDA Super Cub 50 AA01 (Rear), HONDA Super Cub 50 C50 (Rear), HONDA Super Cub 50 AA01 (Rear), HONDA Super Cub 50 C50 (Rear)
Spokes on rear wheels
I bought knitting needles to replace the old ones, the installation is easy, I am satisfied with the result. Thank you webike for buying good quality budget knitting needles.
I bought spokes instead of the old ones, the installation is easy, I am satisfied with the result. Thanks to webike that you can buy budget spokes of good quality. -------------------------------------------------- -------- I bought knitting needles in return for the old ones, the installation is light, I am satisfied with the result. Thanks to Webike for buying budget spokes in good quality. I BOUGHT Spokes Instaad of the Old One, The Installation is Easy, I am Satispied with the Result. Thanks to webike that you can buy budget spokes of good Quality. Powered by Google Translator
View detail
Fits: HONDA Super Cub 50 C50 (Front), HONDA Super Cub 50 AA01 (Front), HONDA Super Cub 50 C50 (Front), HONDA Super Cub 50 AA01 (Front)
Spokes on the front wheels
Spokes on the front wheels.
I bought knitting needles to replace the old ones, the installation is easy, I am satisfied with the result. Thank you webike for buying good quality budget knitting needles. I bought spokes instead of the old ones, the installation is easy, I am satisfied with the result. Thanks to webike that you can buy budget spokes of good quality. -------------------------------------------------- -------- Knitting needles on the front wheels. I bought knitting needles in return for the old ones, the installation is light, I am satisfied with the result. Thanks to Webike for buying budget spokes in good quality. I BOUGHT Spokes Instaad of the Old One, The Installation is Easy, I am Satispied with the Result. Thanks to webike that you can buy budget spokes of good Quality. Powered by Google Translator
View detail
Fits: HONDA Super Cub C50, HONDA Super Cub C70, HONDA Super Cub C90, HONDA little cub, HONDA Super Cub C50, HONDA Super Cub C70, HONDA Super Cub C90, HONDA little cub
Cheap and Parenthesis good
It is inexpensive, looks good, and is highly satisfactory. View detail
Good quality and excellent price
Nice rim, product showed tough, lightweight and looks great. There was not any trouble with the installation on my bike. Excellent pricing and fast shipping. View detail
Not JAPAN, but acceptable
Used for CUB.
Since it is not JAPAN, the accuracy is not as good as it could be.
Motorcycle that runs as slow as a CUB could use it.
Give up on the flares because they are less than 1mm in length and width even if you do your best to adjust them.
View detail
Cospar good
OEM Product had deteriorated and was replaced.
OEM Material:The texture is better now that we have changed from Plastic to Gold genus.
The 19πHandlebar from SEA BASS will not fit without modification, but it can be installed by replacing it with an OEM rubber.
I am satisfied with the improved appearance.
View detail
Fits: HONDA Super Cub 50 AA01 series, HONDA Super Cub 50 C50 Series, HONDA Super Cub 50 AA01 series, HONDA Super Cub 50 C50 Series
Cost-effective and high quality.
Steel's OEMWheel is covered with rust and there is no way to remove it, so it was replaced with a new one.
Material:Aluminum.
Not front and rear, but only rear.I will try to replace the rear first to reduce weight.
good point
Lightweight and improved under-spring performance.
OEMSpoke can be diverted.
The aluminum buffing is also beautiful.
Costa Ricas is also good.
A bad point
Spoke reupholstery is Large.
As a result, the Rear is lighter, and I feel that it runs lighter as well.
It's aluminum, so it's easy to clean.
View detail
Fits: KAWASAKI Zephyr χ, KAWASAKI Zephyr 750 RS, KAWASAKI Zephyr 750, KAWASAKI Zephyr 110, KAWASAKI Zephyr 110 RS, KAWASAKI ZRXII, KAWASAKI Zephyr 400
That's not the picture
It looks shiny in the photo, but the actual product is dull. View detail
Fits: HONDA GROM, HONDA MONKEY125, HONDA CBR125R, HONDA CROSSCUB110, HONDA NSF100, HONDA SUPER CUB110, HONDA XR100MOTARD, HONDA CRF100F, HONDA APE 50, HONDA APE 100, HONDA XR50 MOTARD, HONDA CD-based Engine, HONDA CUB System Engine, HONDA GORILLA System Engine, HONDA MONKEY Engine
with MagnetDrain bolt
Drain bolt with Magnet
I wanted to change it and bought the cheapest one I could find.
It arrived right after the Oil exchange, so it has not been used yet.
It's going to be a while before I can get to it.
Aluminum texture is good.
View detail
To the detriment of Down fenderization.
MONKEY125 is set to Down fender.
Brake hose that will play around with you.
I bought it to fix it.
*To Tireetc. without fixing
I don't think there will be any interference, so I am self sufficient.
OEM Bracket Location
I wanted to install it.
Cutting the Handlebar to Right
In the Air Filter box.
It hit me.
We installed it in a slightly lowered position.
39π and is Exactly.
Rubber sheetetc. to prevent scratches.
I recommend 41π for those who want to put it up.
I use Vinyl Tape on the inside.
I've responded by pasting it in.
I don't know if it works lol.
View detail
Fits: HONDA Super Cub C50, HONDA Super Cub C70, HONDA Super Cub C90, HONDA little cub, HONDA Super Cub C50, HONDA Super Cub C70, HONDA Super Cub C90, HONDA little cub
Position slightly higher on the waist than OEM!
The OEMSeat has a slippery surface, which is good on flat terrain, but when going downhill, it makes your ass gap forward (sweat).
Especially on long descents, this makes it difficult to turn the Curve because you have to maintain your posture with your arms and footpegs…
From this downhill experience, buy here!
The epidermis is coarse and stitched.
My ass is a lot less likely to gap forward.
And the Seat is about an inch or two thicker than the OEM.
The footing might be worse.
Gentle on the ass sounds good!
If you've been riding for a long time and you're thinking of replacing the Seat, you're in for a real treat.
Is this cheap enough for you?
If you want to make your custom look cool and thin, this may not be the right choice for you.
It's a thick seat, so it's not very stylish…
View detail
Fits: HONDA GROM, HONDA MONKEY125, HONDA CBR125R, HONDA CROSSCUB110, HONDA NSF100, HONDA SUPER CUB110, HONDA XR100MOTARD, HONDA CRF100F, HONDA APE 50, HONDA APE 100, HONDA XR50 MOTARD, HONDA CD-based Engine, HONDA CUB System Engine, HONDA GORILLA System Engine, HONDA MONKEY Engine
It's faster to buy.
This is a type of Drain bolt which has a Wiring hole from the beginning.
I bought it because I needed it for regulation when I wanted to race with CUB.
Drain bolt itself is Material:Aluminum with Magnet inside.
Personally, I was happy with the same iron as the OEM, but it was a bit odd to drill the holes on my own with a Drill.
I think it's faster to purchase. The price is cheap, too.
View detail
Fits: HONDA Super Cub DX, HONDA little cub, HONDA Super Cub STD, HONDA press cub, HONDA Super Cub DX, HONDA little cub, HONDA Super Cub STD, HONDA press cub
It is slightly long.
I use it for my LITTLE CUB.
There is a difficulty in fitting. Because it is a little long, the grip end part is left over.
The Switch box cannot be moved, so it cannot be used as a countermeasure.
View detail
Do you like the color Orange? Amber.
What is Amber? At first I thought, "What is Amber?", but this time I bought it and used it.
Orange color is a good color, so I was satisfied with the color.
View detail
It glows well!
I replaced the Valve as soon as possible.
It's a bit of a blur.
View detail
If you just want to use it, this will do the trick!
You may want to relocate Mirror quite a bit and use it, right?
With OEMs, it's often attached to the switch box or rebar clamp, and this is handy when you want to get it out of the way.
This type of product is available at PinDrill, but if you just want to relocate it, this is good enough for you.
View detail
Cost-effective License Plate Light
I bought it for the ZX-11
It is easy to install as it is tightened to the number of bolts
Wiring is no problem if you connect it with the Bullet Terminal and Coupler Mm
And the light is perfect! It's too bright
You can choose the color of the License Plate Light itself, I chose Gold It was good for the price
License Plate Light is available from various manufacturers, but Isn't the License Plate Light here a pretty good cosmetic?
View detail
fashion-conscious
The CALI Seal, which looks small in the License Plate, will have a dedicated room for you It's all dressed up! More than 60 words on this product is soberingly hard.. View detail