Reviews
It got brighter.
Replaced Headlight Bulb on Z125PRO.
The purpose was not only to make the engine brighter, but also to reduce the load on the battery (power saving). The Z125PRO had LED lights from the beginning, so there was no need to replace the tail lamps. I thought about replacing the blinker light because it has a normal bulb in it, but I decided not to do it because the blinker relay seems to be built into the meter and it would be complicated to change it to LED. This time, I decided to replace the Headlight Bulb and the Position Lamp with LEDs, and for the Headlight, I chose this product, which was the cheapest among the Sphere Light products.
The replacement work was as simple as removing the headlight cowl and replacing the valve with the original one, and since the valve is compact, there were no problems with installation.
As for the feeling of use, the light is bright enough and feels very bright, probably because the light is whiter. I was able to drive safely at night. I was not bothered by the dispersion of the light. Unfortunately, there was not enough of an energy saving effect that I could really feel.
Compared to when we replaced the LEDValve on our ZRX1100 a few years ago, low-cost products are now on the market, and the hurdle for replacement has gone down. If you are concerned about the brightness of your lights, we recommend replacing them with LEDs.
View detail
From Halogen to LED
The installation itself is easy, but it was very Large strange to fit it inside the Headlight.
Headlight floated and was very hard to close. I had to adjust the Wiring many times, and after pushing it in with a lot of effort, I couldn't close the Screw by myself and had to ask my family for help. I wonder if the Wiring I pushed in is Large sturdy… Spring was used as OEM.
View detail
Sure, it's bright, but...
Used for Cub Pro (JA10).
Installation, but Controller does not fit within Light.
It will be installed outside.
It was installed under the FrontBasket.
I ran it and it does indeed brighten up.
However, there is a mysterious light on the Left. This is for oncoming cars and people.
It is thought that it will be dazzling, so I put a Tape on the Headlight.
We made it harder to get out.
The brightness is good, but the light scatters, so that was Minus.
Caution should be exercised by those who are concerned about oncoming illusions.
View detail
LED for Sphere LightMotorcycle
It is bright and nice for the price. I would buy it again next time. View detail
Small work is required for installation.
We replaced the headlight with LED to cover the power consumption of electrical components in winter. I have not driven at night yet, so I do not know how much brighter the headlight is, but I could feel that it is much brighter during the daytime. The optical axis also seems to be large and strong.
The only thing to note is that the Controller and Coupler will not fit in the Bonneville 120 Headlight case.
I installed it on the Headlight BracketReverse side.
View detail
bright
Halogen, I was dealing with, it is quite bright, Kojuk, Large was strange until I put it out! View detail
I wanted a little more brightness.
Brightness is still proportional to the Gold amount. View detail
Recommended over high efficiency Valve
It is installed on Vmax and TRX.
Vmax requires hang and force for installation, but can be pontooned.
There is a slight shadow under the illuminated area, but compared to the OEM Halogen bulb, it is not as bad as the OEM Halogen bulb. Lighten up." I feel. In fact, I bought it to reduce the burden on Battery rather than the brightness of Light.
I mounted it on the TRX and measured the brightness with an SLR and it was definitely brighter. (Illuminance seems to change with color temperature.)
Also, the brightness and light distribution will change from NORMAL Halogen depending on the shape of the reflector, the state of the plating, and the lense cut. Please be aware of this.
View detail
JAPANLED Headlight Bulb
I bought a Dio110 and installed a leftover LED headlight bulb, but the light was diffused and somehow not good enough. I was very careful not to scratch and break the plastic claws.
The deciding factors for purchase are Japan, long life, 2-year warranty, and so on. Cheap Other Brand Products are also getting better in performance, but there is a difference between the best and the worst.
View detail
Sphere LightGod of thunderG3
I had been using God of thunder 3 lights, but I had a hard time seeing at night when driving through mountain passes. I can drive on mountain passes without any worries. View detail
If you want to replace Valve, this is the one!
RC390 (2021 model year) The OEM Halogen Headlight was too dark, so we replaced it with this LED Headlight Bulb.
The quality and texture of the product is perfect.
The process is similar to a typical Valve replacement, such as removing the OEM Valve from the Coupler, removing the ValveBody and assembling it in the reverse order as when the new Valve for the LED was removed, and putting together the Wiring.
However, there is a gray cap on the reverse side of the headlight of the 2021 RC390, which may slightly interfere with the aluminum heat sink. Therefore, we installed the headlight by rotating the LED bulb first and then pushing the cap in, while sticking the cap halfway in.
When I purchased this product, I was not sure if I could afford this price for two Valves since the 2021 RC390 has two lights.... But when I installed it, I was very impressed with the brightness.
Both Hi and Lo can be installed with the same work and no modification, and the brightness of the product is highly satisfactory with no complaints.
View detail
From Chinese HID to Sphere LightRIZING2
Used for low beam of TDM900.
Additional Spacer 1980 yen is required for installation. (I could have made it myself)
Since the rubber packing in Included Parts:does not fit, the coupler will not fit unless the original rubber cover is cut.
When we got the vehicle, it already had 35W Chinese HIDs, so this is not a comparison with NORMALHalogen.
Even though it is a Chinese HID, it is 35W, so it was quite bright, so even after replacing it with RIZING2 LEDs, it seems a little dark.
The color temperature is higher than that of HIDs, or perhaps the color is comparatively blue.
I would have preferred 4500K.
However, I am glad to know that the symptoms such as the engine igniting when the high beam is turned on while the low beam of HID is turned on, as if the voltage had not caught up with the low beam, the light disappears for a moment, and the engine ignites, are gone.
View detail
LED from Halogen
I switched from Halogen to LED!
I think it is a little BlueWhite.
I am very satisfied with the dress-up effect and the ease of viewing.
View detail
RIZING3 H4Hi/Lo installation and usage
Vehicle installed:SEA BASS DJEBEL250 XC
The heat sink interferes with the black plastic parts on the headlight reverse side, so it is necessary to shave it off. The wiring of the HID unit may be a little long, but it will not be a problem for installation.
The feeling is that it is very bright and the light distribution is not bad as I used to use cheap Halogen bulbs from Auto for Vehicle.
It is a good product for those who have a Grip heater or other equipment installed afterwards, as it consumes less power.
View detail
Good product
The light can reach very far in the close-up mode. The telephoto mode is not very impressive. I mainly use low beam so the product is very suitable for me. I bought a lamp with a color temperature of 4500k which gives a pretty good light. --------------------------------------------------- -------- The lighting is very far in the projection mode. The far projection mode is not very impressive. I mainly use close lights so I see the product that is right for me. I bought lights with 4500k color heat quite well. Powered by Google Translator View detail
Processing required for Bracket type
In the always-on VMAX, the Chinese LEDs died early, probably due to heat.
This time, I wanted to go with a domestic product for somewhat longer life, so I decided on Sphere.
God of thunder 2 was rejected due to its length.
If God of thunder gu ALPHA, I thought the length is Large sturdy and bought it.
However, the claws on the pedestal are not clear whether they are designed for the strength of the aluminum diecast or not, but there is an extra part of the pedestal, and the lock does not close due to the claws if the VMAX with Ring Type Valve BlockCap is not a Harigane Lock Type.
Since the Valve is an Aluminum Diecast body, it can be inserted by shaving it with a Leutor.
Brightness and optical axis were Large sturdy.
Clearance in the back is also included.
If you assume some processing, it is better to do a lighting test and process if Large sturdy, considering the warranty for initial defects. If you do the processing first, you will not get the warranty.
View detail
Bright and white
RIZGIN2 is a fanless type LED headlight.
The bracket of the base is installed first, then the waterproof cap is installed, and then the body is inserted and attached as if it were hooked.
The controller is relatively small, and installation itself is easy.
Note that Cutline may not appear for LED Headlight depending on Lens/Reflector shape.
In the case of the MT-09, it seemed that the optical axis adjustment had to be set very low to pass inspection (depending on the chassis).
View detail
Headlight replacement!
The OEM head lamps are perfectly fine, but I saw a friend's Motorcycle and thought they looked nice, so I replaced them.
I don't feel anything special in the morning or during the day, but about dusk to nighttime, it is much easier to see.
Replacement is also easy!
View detail
Used for DAX Headlight.
Full-wave rectification is used for DAX of DC Spec.
Before this LED Bulb, I used a slightly more expensive Sphere LED Bulb.
No difference is perceived in brightness, current consumption, etc.
This means that the cosmetics are very good.
It would be ideal for trial use.
Incidentally, the removed LED Bulb was installed in a BOLT Shoulder Bag and the optical axis was adjusted.
As a result, the light intensity, cutline, etc. were at a level sufficient to withstand vehicle inspections.
The appearance of the LED Bulb still seemed to have a reduced number of components.
The biggest difference is the weight. The feeling of holding it was totally different.
It comes with a one year warranty, so I'm sure it won't break during that time.
I expect it to last a long time.
View detail
Good visibility.
We chose 4500K because of its longer wavelength and better visibility than 6000K. The power consumption has been lowered from Halogen, and the out-of-ball warning light has remained on. We are considering the need to incorporate a warning light canceller in the future. View detail