Reviews
new setup,great look,cheap fuse
Great sprocket bolt kit! The finish is slightly mat than OEM which looks awesome when paired with a new aftermarket sprocket.Great set of fasteners for replacing the stock ones. They are a little longer and the allen head used is a few sizes larger (doesn't round as easily) than the stock ones did however have to tighten them again after my first ride. After that they have stayed tight. I'm glad i bought these as they work great. Much easier to tighten without being worried about stripping the things.webike too fast,Because it is packaged very well, it is subjected to extra inspection at customs.But the shipping fee is high. View detail
Cost-effectiveness is good enough
The price was low... and the equipment was good enough! The tightness was good. View detail
Is good
I replaced it with a Sprocket made by the company, so I purchased it at the same time.
It is a special product, so it can be used without any modification, and it can be used in a wide range of applications.
No problem.
It does not come loose and is adequate for performance.
View detail
Exclusive Design is the only way to go!
I used it to replace the Sprocket on my 2007 wr250X with less than 16,000 miles. I fixed it with Red Lock to prevent loosening and it is perfect. Drivetrain weight reduction is easy to feel! View detail
When you replace the Sprocket, you should also replace the Bolt.
This is the Tapered Nut for DRC's Dura Sprocket. wr250X needs this because the OEMSprocket fixed bolt cannot be reused because the face is flat. The Dura Sprocket can last up to 20,000 miles if you keep up with maintenance, and it's a once in a few years expense, so it's time to replace it. View detail
I use it for WR.
I switched to DRC's Sprocket and bought this Bolt set to go with it.
The nut is a lock nut, so there is no worry about it coming off at the moment.
View detail
Taper bolts needed to fit the Sprocket
Since the KLX230R's OEMSprocket is a straight bolt Purchased to install a DRCSprocket
Quality is fine, no snags in the hand-tightening stage
The Hexagon Bolt was not easy to lick
Hang of the work hard to lick, Hexagon Bolt with a proper tool to the extent that it is held down and It is better to tighten it on the Nut side
You can have an OEM Taper bolt, but the cost performance is It's good and no doubt
View detail
I'm a bit of a wreck
I bought it for my KLX250
I use DRC's products a lot, and so does Sprocket
I felt like the OEM Bolt was getting sucky
I ordered it when I was on a side trip
View detail
I'm impressed
Includes 6 Taper bolts and lock nuts for Sprocket mounting Quantity:Set。
Now I can install the Sprocket on my WR250 It looks rustproof and a very good buy
View detail
No problem so far
WR 250X I exchange Bolt at the same time as Sprocket exchange of 2007 year.
I am driving without trouble for now without looseness.
View detail
It is consumable parts.
Rear sprocket We exchanged at the same time when exchanging.
If this price is exchanged everything will not be regrettable.
Rigid feeling ? Fit feeling is also good.
All Quantity : Set so it's safe.
View detail
enough
OEM is too expensive when exchanging, so use this.
There is also a reputation for easy licking, but I think that work is probably only bad.
It's enough.
I have never Trouble so far.
I will keep using it for the future.
View detail
Renthal used for 48 Sprocket installation!
NORMAL's Bolt is 10 mm and Renthal 48 Duo Sprocket can not be installed, but this Bolt solves! Off car is a salvation Bolt who is supposed to think Renthal's big sprocket is cool! W View detail
With Sprocket exchange
Rear sprocket I bought it along with the exchange.
Since Bolt & Nut attached to purchased Sprocket was able to be used, this is unused but I think that it is a good good item for Cost performance.
You can also use it with other models.
View detail
Great
I only forgot it because I forgot to take a picture
This Bolt / I think Nut is wonderful.
It is recommended!
Nut must be locking prevention.
Bolt's Length is the best.
It is not too long, not too short, it's an ideal length!
Perhaps it was perfect as it was combined with DRC's Sprocket,
Although a certain Manufacturer's Sprocket comes with a dedicated Bolt
Bolt is long. I was slightly disappointed..
When exchanging other Machine Sprocket, this Bolt / I will change to Nut.
Based on my experiences, this one definitely has good serviceability w
View detail
Price difference with OEMBolt is obvious
OEMBolt is 1 pc / Considering about 200 yen, the price difference is clear. I changed it cheaper if I was in Sale. I think that it is best if there is also 10 mm diameter Bolt if possible.
ME06's hub is 10mmBolt so I used OEMBolt this time ...
View detail
For anything Cost performance
Bolt, Washer, Nut set This price is cheap. I like places that are in a simple package and not over packed. I can trust in DRC. There was no problem running with 2 ST 250. I purchased two before because I purchased it very well, so this time. It is good even if it is reserved.
View detail