Reviews
Used for CRF250L
We used it to fasten X.A.M's Driven Sprocket.
The OEM is M10Bolt, so an M8 conversion Spacer is required to use this one.
The OEM tightening torque is 50 N.m, but when I tried to tighten it with the same torque, it seemed to lick, so I tightened it with a little less torque.
I wonder if you could write the stipulation Torque in the Package.
View detail
DRCRear sprocketBolt nut
Bolt nut for the new Rear sprocket.
It is a dedicated product and fits well.
Since it is a component that can easily come off, inspection before driving is a Large cut.
View detail
No problem!
When I replaced the Sprocket, one of the Screws came off after a while, so I bought this product, which has the same DRC as the Sprocket.
So far, I have used it without any problems.
View detail
I can use it without problems
[How is it used?
I installed it on my D Tracker 125.
In order to install DRC's Dura Sprocket, you have to replace the OEM Sprocket bolt with this Taper bolt.
Dura Sprocket
https://www.webike.net/sd/21312642/
Was the installation difficult?
All I had to do was remove the OEM and replace it.
The OEM SprocketBolt comes with a screw lock agent, so after removing the OEM, you should clean up the screw lock agent debris.
How was your experience with it?
It worked normally
I will be happy if there is no rust in the future.
View detail
Cheaper than OEM Parts Number
【What made you decide the purchase?】 I used it even before cheaper than OEM Product. Bolt, Nut, Washer is doing Set and Nut is Self Locking Nut and there is no need to use Screw lock agent.
【How was it actually used?】 You can install anything without problems. Besides this time's Wheel, using it for about 2 years with durability and corrosion resistance has not caused any problems at all. I do not know yet more durability.
【Was it difficult to install? (Hard parts case)】 Easy 6 mm Hexa and 12 mm should preferably have StraightGlasses or longer Combination
【Please tell me the point of installation and hang (in the case of Hard parts)】 Tightening Torque is firmly. Spoke gets in the way and all the Nuts can not be locked in Torque wrench, but I remember the tightening and leaving the other Nuts with the same Torque. I think there is a problem with tightening Torque shortage, but I think that a little overtorque is problematic.
[Is there anything I was disappointed about?] It was an unchanging product as I have purchased it before.
【Hope for Manufacturer - Please tell me if there are any improvement points】 I wonder if the finish is beautiful a little more Plating
【Have you compared items?】 OEM Product, BOLT Shoulder Bag, ZETA
[Others] Finishing is a price, but it is a firm product. Since it is Self Locking Nut, it is exchanged for new items each time Sprocket is exchanged.
View detail
It is cheaper than OEM and satisfactory product
I purchased it simultaneously with RSprocket of DRC.
Nut was properly Lock nut, it was a cheap and satisfying item than OEM.
I do not know the durability yet, but I think that it can be used without problems.
View detail
DRC Sprocket Bolt/Nut
I purchased at the same time as it is necessary for Dura Sprocket installation.
I think that it is necessary and sufficient strength and construction, but whether the accuracy is low or the movement that the hexagonal hole is slightly transformed - - -
View detail
easy to handle
Originally, I bought it by mistake, but ...
Sprocket boltNut of CRF 250L is M10, so it is natural, but as the diameter is different, a gap is formed and the Sprocket moves.
Spacer which fills this gap at another site was sold, so I use it in combination with it.
So ... Sprocket boltNutM.
The serviceability is Up even if I say anything. By the way, I believe it is lighter than OEMBolt nut, so Petit is weight saving
View detail
Attached to HUSQVARNATE 510
HUSQVARNA(SMSpec. ) Purchased to attach Sprocket.
Because the price is also cheap and has become a reliable Brand
That's alright..
HUSQVARNA sometimes screws here loosen easily and sometimes come off (once disaster catastrophic... ) So let's check firmly!
View detail