Reviews
ACERBISKnee braceUnder sleeve
I have been wearing long tights and this was my first time to wear an undersleeve, but I was looking for something cooler and hotter than my long tights. View detail
Fits: YAMAHA TENERE 700, YAMAHA MT-07, YAMAHA XSR 700, YAMAHA TRACER 700
It is quite cool!
This is a resin Guard for Engine case cover. We wanted something lightweight and well-designed, so we installed this product on a trial basis!
-Difficulty of assembly
I have no complaints about the accuracy. This is the spec. to remove the bolt of Both Sides of the car and tighten this product together. The attached Gold Spacer is attached to the plastic cover and the tightening part is made of a quantity of Gold Spacers.:If you do not remove the bolt of the engine case with the vehicle body in a vertical position using the center stand or maintenance stand, the engine oil may leak out! The Instruction Manual says so. I used a maintenance STAND to keep the car in a vertical position, and there was no oil or coolant leakage. The tightening must be done at the specified torque (12N-m), so a torque wrench is necessary if you do the work by yourself. If you have the tools, it is an easy installation that takes only about 10 minutes.
-Quality and texture
The installation accuracy is not a problem at all, and the elaborate shape that matches the complex shape of the engine and the design that matches the engine side would make it seem like OEM parts if it did not have the ACERBIS logo on it.
View detail
Touch Touch Touch here♪
The regular Smartphone Holder is convenient, but it was wobbly and unreliable. I thought a Type that would not drop on bad roads would be better, so I purchased ACERBIS's HandlebarTool bag. My phone is KYG03.
The upper lid is held on by a Velcro and Buckle. The lid is raised and opened and closed with the Zipper. I found the long Velcro to be cumbersome. It is very snaggy, but I think it will become easier to open in time.
I put the tools in the included Toolholder. I also put a hand-pushed air pump in it. Back did not lose its shape.
It fits CRF250RALLY and SEROW without any problem. The back is larger than the bar pad.
Unlike the Smartphone Holder, the smartphone screen is up. Gloves and bare finger touch are also effective.
The Toolholder is white where the tool hits it. The Rubber to hold it down is also thin and cheap, unlike the construction of the Back. I use the same kind of thing purchased at 100s of dollars. It is one part of the product name, but I did not expect it to be replaced.
This backpack is convenient for touring on forest roads and can be used as a Smartphone Holder. It is recommended for long-distance travelers with a lot of luggage.
View detail
Fits: GASGAS EC250F, GASGAS EC300, GASGAS EC350F, GASGAS EC250, HUSQVARNA FE250, HUSQVARNA FE350, HUSQVARNA FE450, HUSQVARNA FE501, HUSQVARNA TE150I, HUSQVARNA TE250I, HUSQVARNA TE300I, KTM EXC-F250, KTM EXC-F350, KTM EXC-F450, KTM EXC-F500, KTM EXC150TPI, KTM EXC250TPI, KTM EXC300TPI, KTM XC-W125, KTM XC-W150TPI
Mounted on Beta RR2T
I installed it on my beta RR2T 250 which I always use for forest road touring.
During touring on forest roads, there will inevitably be situations where the motorcycle must be pulled up, and if there is no place to hold it, such as a stack belt, it will be very difficult to pull it up.
So I immediately purchased this product from ACERBIS.
It contains not only a Belt but also a collar and a long Bolt so that the Belt could be installed and pulled easily. This is a part that I don't like to use as much as possible, but it is a very useful part in case of emergency.
View detail
Fits: YAMAHA TENERE 700, YAMAHA MT-07, YAMAHA XSR 700, YAMAHA TRACER 700
as a stake in a difficult situation
Material:Since it is plastic, it may not be as good as gold as protection for the engine case, but it has a thicker wall and a considerable cover range, so it is likely to be effective. In any case, I am quite satisfied with this product because of its good design. View detail
Fits: SUZUKI V-STROME 650XT, SUZUKI V-STROME 650V, SUZUKI V-STROME 1050XT, SUZUKI V-STROME 1050, KTM 890 ADVENTURE, KTM 790 ADVENTURE, KTM 1290 SUPER ADVENTURE R, KTM 1290 SUPER ADVENTURE S, KTM 1090 ADVENTURE, HONDA MSX 125 GROM, HONDA CRF 300 RALLY, HONDA CRF 300L, HONDA CB 125R, HONDA CB 125F, HONDA CB 1000R, DUCATI MULTISTRADA V4 S SPORTS, DUCATI MULTISTRADA V4 S, DUCATI MULTISTRADA V4, BMW G350 GS, BMW F850 GS ADVENTURE
ARGONHand guard
[How is it used?
I had an Africa Twin OEM hand guard on it, but I didn't like the color, so I replaced it.
The deciding factor for the Largeest was that the color that matched the car's body color was an Outlet item and was quite inexpensive.
Was the one you received as per Image?
It is more luxurious than the OEMHand guard and is as per Image.
Was the installation difficult?
It is easy to replace if you have the right tools.
However, ARGONHand guardSingle Body cannot be installed on X-ADV.
A Mount Kit for Africa Twin must be purchased separately.
[Included Parts:were they on?
Everything needed for installation is included.
As mentioned above, a separate Mantle Kit is required to attach to the X-ADV.
[Was there anything that disappointed you?
The hand guard has a gimmick to spread up and down, but even if it is spread, it will naturally return to its original position.
The Bolt is fixed and seems to be adjusted by retightening.
It would have been great if it could be fixed in the open position.
[ITEMS TO BUY TOGETHER
Mount Kit for AC 24836 is required for installation.
View detail
BITTER BITTER Super motard front fender
I wanted to install a short fender, and after much deliberation with DAYTONA's MOTARDFender, I chose this one because of its design. The installation was done by drilling a hole with a drill after taking the position from the normal fender, since the seal to check the bolt position is included in the package. It was not difficult because I could get the exact position. Spacer was placed between the mounting Bolt and Body to make it slightly forward and lowered to create a combat Image. Other impressions say that the bounce in the rain is great, but this seems to be something we need to be patient with. View detail
Boots Friction Prevention
I am very satisfied with the design and the ease of installation. View detail
The durability of Band's Rubber is poor
After 2 months, the band's rubber corroded and snapped off as shown in the picture.
I had no choice but to fasten it with coated needle gold.
View detail
Weight reduction around handlebar
I have always enjoyed forest road touring with gasgas EC250 as a hobby.
It is an application that sometimes runs a little HARD.
Until now, I have been using ZETA's Guard with Aluminum in it,
The Handlebar end of the Motorcycle, the furthest end of the Motorcycle, is extremely heavy, and with the worsening of the Handleling,
I was struggling with the weight of the Motorcycle when I knocked it down.
Also, the fat bar's bend also became a snap, and for a long time we were troubled with the selection of a hand guard.
To be honest, this hand guard works. However, it can be easily fixed by hand, so I am not particularly dissatisfied with it.
Since it is not made of aluminum, it is very lightweight. The lever protection is also very good, and so far it has protected me well.
Total performance is very good. It seems to be my ideal Hand guard.
I would like to test how far it will endure while actually using it, since it is plastic in nature.
By the way, although it is Plastic, it is surprisingly sturdy.
View detail
As a light Fender
Purchased as a lightweight for Fender.
There is a different MODEL of the same ACERBIS, but this one separates the front and back Fenders.
I also bought it with the expectation that it would have a cooling effect since it can send VANVAN running air to the Radiator as it is, since it is shaped to have a hole in the middle when used only with the front Fender.
As a result, handling is lighter and we have no complaints about cooling.
In addition, since a back fender would have to be attached to the car if it is to be driven on dirt roads, please consider this as a proposal for use by Maine city drivers or those who can drive only on paved roads.
View detail
Match the color.
Product Name
ACERBIS ACERBIS TRI FIT Hand Guard TRYFit
Item Number
AC-16508RD
Vehicles
Honda CRF125F 2024 MODEL
Number of man-hours
15 min.
Required Tools
Torque wrench, hexagon socket, Hexagon socket, Extension bar, Combination wrench, -Driver, Hammer, Pliers, etc. would be perfect.
Why did you choose this product?
I was looking for a red hand guard and chose this one because it was highly rated.
Was the one you received as per Image?
It was just like the Image. Cool looking
Was the installation difficult?
It is not difficult because all you have to do is fasten the screws.
How was your experience with it?
I am very satisfied with the product and would recommend it to anyone who is looking for a hand guard.
[Included Parts:were they on?
There were Instruction Manuals for handling Seal, etc.
[Was there anything that disappointed you?
None in particular.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: KAWASAKI KX 250, KAWASAKI KX 250X, KAWASAKI KX 450, KAWASAKI KX 450X, KAWASAKI KX 250F, KAWASAKI KX 450F
To protect Chain.
Product Name
ACERBIS ACERBIS Chain Guide Block2.0
Item Number
AC-17950BK
Vehicles
Honda CRF125F 2024 MODEL
Number of man-hours
20 min.
Required Tools
Torque wrench, hexagon socket, Hexagon socket, Extension bar, Combination wrench, -Driver, Hammer, Pliers, etc. would be perfect.
Why did you choose this product?
I chose this one because CRF125F does not have a solid Chain Slider. I also chose it because it was recommended by others.
Was the one you received as per Image?
It was just as Image.
Was the installation difficult?
It is difficult for an amateur to get it on the CRF125F because you have to weld it on. A welder is required.
How was your experience with it?
It is solidly built and Enduro will be able to do so without worry.
[Included Parts:were they on?
None in particular.
[Was there anything that disappointed you?
None in particular.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Works like a skid plate should
Installation will require only 5mm bolt. Color match is wonderful for bike. Immediately took this to a local trail to test it out and managed to slam it on some rocks. Held up great, took a bit of damage but that's what it's for! Its tough but it's still plastic so I'm sure it has its limits.something to protect the finish on the frame and keep the mud off the motor.Little to no gaps, excellent coverage of major components.You will need to remove this skid plate when you change your oil.But if you are a little lazy about your oil changes, this may not be for you.This is the perfect solution and was reasonably priced. View detail
Fits: YAMAHA YZ250F, YAMAHA YZ450F, YAMAHA YZ250FX, YAMAHA YZ450FX, YAMAHA WR250F, YAMAHA WR450F
It doesn't fit
It is not compatible with YZ250FX2023MODEL, though it is compatible with YZ250FX2023MODEL.
I have removed the NORMAL White Ring as per the instruction manual, but it is not attached.
View detail
I am very satisfied with the fast delivery. Thank you webike.
I am very satisfied with the fast delivery. Thank you webike. I will repurchase it next time The packaging of the product is very good View detail
O-ring is Garbage
I thought I read that TENERE fit up to 23, but I bought it.
No problems with installation, no interference with brake pedal etc.
There is no particular change in operability, but it seems to be easier to apply the ankle area to the vehicle body.
The other thing I would like to see is the appearance and the ability to put a lid on the Pivot shaft mounting.
There is nothing wrong with the accuracy of the product itself, but the weatherproofing of the O-ring that comes with it is very weak! I don't think it will last more than 2 months.
It is possible to substitute the O-ring fixing part with Tie Wrap. However, I would not use this material because it does not look good.:I have replaced it with a SiliconO-ring and am using it. So far there has been no deterioration.
View detail
good
looking good but its for light use not for hard rally use as its just plastic guard . will definately buy one with metal frame next time View detail
Frame protection and improved gripping
Off-road motorcycles tend to peel off the paint on the frame when riding in Boots, because the frame is inevitably caught between the legs when standing.
From the viewpoint of preventing paint from peeling off and rusting, it is recommended to install frame guards.
Installation is easy because it is only fastened with a washer (sturdy rubber), but side covers and sprocket covers cannot be installed properly unless they are removed, even if it is a pain in the ass. It is a bit of a hassle, but it would be better to remove the Cover before installation.
View detail
Fits: KTM EXC150 TPI, KTM SX125, KTM SX150, KTM XC125, KTM XC-W125, KTM XC-W150 TPI, HUSQVARNA TC125, HUSQVARNA TE150I, HUSQVARNA TX125, GASGAS MC125
be too soft
Used on a KTM 150EXC.
Purchased because it has a slightly wider range of protection than the Under Guard that comes with the OEM and is more reasonably priced.
The back end is hooked to the Frame and the front end is bolted via a special Bracket.
I was driving on a rocky OffRoad course and I noticed that the back end had come off and bLOOVE it. I thought that was ridiculous and reinstalled it by deflecting the product with my hand. It went back on easily. No, if it bends and distorts so easily, that's why it comes off right away. As I expected, it came off right away and I was in love with it.
I had no choice but to fix the back end with a thick Tie Band and ran that day, but I immediately returned to the OEM one and it has been in the drawer ever since.
It seems to come off easily when you go igoigo with the underbelly applied, so I guess it is good if the course has no stir, such as a rocky area. It seems that the position of the bolt fastening at the front end is too far forward, which is also not good.
I don't know about the SX and the Guard itself, as they seem to share the same fixing method, but the Guard itself is too soft anyway.
I also hit a rock hard under the belly with this Guard on and it dented the Frame a little. I am very disappointed, however, because I have never had a Damage on the Frame with the OEM Guard in the same way.
View detail