Reviews
Fits: YAMAHA TENERE 700, YAMAHA MT-07, YAMAHA XSR 700, YAMAHA TRACER 700
as a stake in a difficult situation
Material:Since it is plastic, it may not be as good as gold as protection for the engine case, but it has a thicker wall and a considerable cover range, so it is likely to be effective. In any case, I am quite satisfied with this product because of its good design. View detail
Weight reduction around handlebar
I have always enjoyed forest road touring with gasgas EC250 as a hobby.
It is an application that sometimes runs a little HARD.
Until now, I have been using ZETA's Guard with Aluminum in it,
The Handlebar end of the Motorcycle, the furthest end of the Motorcycle, is extremely heavy, and with the worsening of the Handleling,
I was struggling with the weight of the Motorcycle when I knocked it down.
Also, the fat bar's bend also became a snap, and for a long time we were troubled with the selection of a hand guard.
To be honest, this hand guard works. However, it can be easily fixed by hand, so I am not particularly dissatisfied with it.
Since it is not made of aluminum, it is very lightweight. The lever protection is also very good, and so far it has protected me well.
Total performance is very good. It seems to be my ideal Hand guard.
I would like to test how far it will endure while actually using it, since it is plastic in nature.
By the way, although it is Plastic, it is surprisingly sturdy.
View detail
Match the color.
Product Name
ACERBIS ACERBIS TRI FIT Hand Guard TRYFit
Item Number
AC-16508RD
Vehicles
Honda CRF125F 2024 MODEL
Number of man-hours
15 min.
Required Tools
Torque wrench, hexagon socket, Hexagon socket, Extension bar, Combination wrench, -Driver, Hammer, Pliers, etc. would be perfect.
Why did you choose this product?
I was looking for a red hand guard and chose this one because it was highly rated.
Was the one you received as per Image?
It was just like the Image. Cool looking
Was the installation difficult?
It is not difficult because all you have to do is fasten the screws.
How was your experience with it?
I am very satisfied with the product and would recommend it to anyone who is looking for a hand guard.
[Included Parts:were they on?
There were Instruction Manuals for handling Seal, etc.
[Was there anything that disappointed you?
None in particular.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Works like a skid plate should
Installation will require only 5mm bolt. Color match is wonderful for bike. Immediately took this to a local trail to test it out and managed to slam it on some rocks. Held up great, took a bit of damage but that's what it's for! Its tough but it's still plastic so I'm sure it has its limits.something to protect the finish on the frame and keep the mud off the motor.Little to no gaps, excellent coverage of major components.You will need to remove this skid plate when you change your oil.But if you are a little lazy about your oil changes, this may not be for you.This is the perfect solution and was reasonably priced. View detail
Wide range of Guard
It is more solidly built than I had expected, and my imagination that it was just a plastic board was betrayed in a good way.
Installation is easy, as only four screws are needed for installation.
I think it is better to install it after Grease up well because the screw holes are likely to be rusted by water in the location.
Since it covers the underside of the Crankcase, I think the construction is quite promising in terms of Engine protection.
View detail
protection against cold
Inner Weight inside Handlebar Pipe must be removed.
The Handlebar on my vehicle is welded with a Weight of Plug.
I purchased a Handlebar separately since it is non-disassembled.
Tightened up with M8 Socket Bolt included in the structural
The structure is fixed in place, but it must be torqued considerably.
It is not locked, so be careful of head slugs.
I have covered with HondaOEM Handlebar Upper Holder Cap.
View detail
Hole position is not good
I put it on my 8BK-MD47, and the holes on the Left side are not aligned when viewed from the Front, so I had to force the Left side up, then the Right side up, then the Bolt in the rear to get the Bolt to fit. If there was a penetrating hole at the oil drain bolt position, it would have been better to save the removal when changing the oil. View detail
Guard
The Size is good and it works well as a Guard. View detail
Does not break the Style of the car body
【good point】
Light
Looks sturdy.
Easy to install.
It is hard to be confused with others.
[Bad point]
The mounting holes were gapped and needed to be machined.
There is no hole for drain bolt.
Fallen leaves accumulate between the body of the vehicle and the Plate.
It could be done more cheaply.
View detail
Because it is an Off car!
I always install it from Muddy to Hard when I run Course and then practice.
Even Racer would not feel comfortable exposing himself naked to such harsh conditions.
Since I started wearing it, I have been practicing with Muddy without any concern, and I have never had any oil leakage.
This is the Level that I would like to have available in OEMOption. (Lol)
View detail
BITTER X-GRIP
Fits well with 2023 Honda crf300l. The delivery of the product is fast and the quality is satisfactory. It is also easy to mount the product, so anyone can mount it. I like the frame protection and design the most. View detail
Fits: HONDA CRF450R, HONDA CRF450RX, BETA RR 4T 350, BETA RR 4T 390, BETA RR 4T 430, BETA RR 4T 480, HUSQVARNA FC250, HUSQVARNA FC350, HUSQVARNA FC450, HUSQVARNA FE250, HUSQVARNA FE350, HUSQVARNA FE450, HUSQVARNA FE501, HUSQVARNA FX350, HUSQVARNA FX450, KTM EXC-F250, KTM EXC-F350 , KTM EXC-F450, KTM EXC-F500, KTM SX-F250
I put it on my EXC-F250.
In the product photo, I think it is on the one that is not F.
I was able to put it on EXC-F250.
View detail
I would love to see LongTwo
It took about 3 hours to install the Cowl, and although it was difficult to align the Bolt, it can be done if you take your time.
It is a good product that can expect more cruising range than RALLY50.
View detail
To protect the Engine in the event of a fall
I put a yz125 engine on my TDR80. I bought this to protect the engine in case of a fall because I might run on the circuit occasionally.
In particular, the Clutch Housing Cover on the EngineRight Side is a must-have product because of its thin, lightweight magnesium cover and water pump.
View detail
I like the fact that it will Guard to LINK.
It functions well enough as an Under Guard, and best of all, it even guards the LINK.
It is sufficient for Enduro race (not Hard).
No special modifications were required for installation.
View detail
Compactness for any type of car
[How is it used?
The OEM tail lamp for the XTZ125 is an adaptation of one used on Yamaha road motorcycles (SRX, SDR, etc.) from the 1980s to 1990s, so it seems a bit large and compact for an XTZ with a raised tail. I wanted to replace it with something a little more compact, so I went to Webike and found this product.
Was the one you received as per Image?
To be honest, it is more Compact and thinner than I expected, and at first glance depending on the position setting. I think the Tail lamp isn't installed!" I thought it would be possible to do the same thing with the Image product. The product was more than Image.
Was the installation difficult?
If you remove the Connection Connector from the OEMTail lamp and connect it to each of them, the functional aspect of the Lamp is finished.
My XTZ125 had a Bullet Type Terminal, but the large size was not quite right, so I replaced the Bullet Terminal on the product side. One of the 3 wiring was Grounding Wire (Black) and one was Yellow and one was Red wiring with Tail & Stop-lamp and License Plate Light, but I can't remember which one is which... Sorry.
The only thing left to do was to fix it to the car body, but there was no good place to bolt it to the car body, so I used several tie bands to fasten it to the seat rail.
Drill a hole for the License Plate in the tongue (the black plastic part that hangs down at an angle) under the Lamp, fix the Number, and you are done.
The Blinker of XTZ is fixed to another part, so no special modification is required.
If you buy the OEM type connector for each manufacturer sold by KITACO and connect Wiring, Wiring will be refreshed and you can easily return to NORMAL. If you purchase the OEM type Connector for each Manufacturer sold by KITACO and connect Wiring, Wiring will be refreshed and you can easily return to NORMAL when you want to return.
How was your experience with it?
I fixed it in a safe position, because I might be involved in an unexpected accident such as a rear-end collision if the tail lamp is not clearly visible when driving on public roads.
[Included Parts:were they on?
This is all the product Body listed in Webike's product section. It is a very simple product.
[Was there anything that disappointed you?
Not at all.
I was concerned about the strength of the tongue portion, but there was no problem at all for just playing in the mountains.
Probably not Large sturdy unless you hit it directly.
Other items that would be helpful
Point and hang of installation
If you want to process Wiring as beautifully as OEM, use OEM Type Connector by Manufacturer as described above. (If you prefer Bullet Terminal, you can leave it as it is, but please perform Waterproof processing.)
[Availability and clarity of the Instruction Manual
I think it is an easy product to understand as an electrical system (?). I think it is an easy-to-understand product as
[Notes]
Nothing in particular, just be careful not to misplace Wiring.
[ITEMS TO BUY TOGETHER
As I mentioned above, this is also available from KITACO and other companies. OEM Type Connection Terminals by Manufacturer will allow one-touch connection to Harness on the car body side.
The method of fixing to the car body varies depending on the car model, so in some cases, the Bracketetc. may be folded, bent, or modified.
First, check the fixation method by placing it on the vehicle in which you want to install it.
[Opinions and requests to Manufacturer
Mine is Large sturdy, but my friend who installed the same product had several LED bulbs that did not glow in some areas. Please improve and stabilize the quality.
View detail
Beware of O-rings
Parenthesis has improved, and I'm generally happy with it,
After a few months, the O-ring deteriorated Quantity:Pair (for Left and Right) I noticed that they were cut off one by one.
If two O-rings on the Clutch Side break off, they may drop out.
Please note
So I re-fastened it with a thin needle Gold.
View detail
Lightweight and easy to install
Material:I managed to put it on because it is plastic, so it bends a little. I have a kx112 that was converted to a public road, so the handlebar area was a bit large and strange because there was no space for switches and such. View detail
usually
It can be used normally, but it is better to retighten it regularly. Especially this type is a pain to remove because it remains inside if it is loosened too much. I wanted to buy the type that has a bolt inside and expands the circumference, but I had no choice because I couldn't find it. View detail
Bitter Bitter X-GRIPFrame protector
Material:It is plastic, so the texture is not that great, but it is sufficient for the purpose of preventing scratches on the Frame.
The rest is attached with rubber, but it is so tight that it will not fall off easily.
View detail