Reviews
Fits: DUCATI SCRAMBLER(800), HONDA CB1000R, HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS, HONDA CB125R, HONDA CB1300F, HONDA CB150R, HONDA CB250R, HONDA CB400SB, HONDA CB400SS, HONDA CB750, HONDA CRF1000L Africa Twin, HONDA CRF250L, HONDA CRF250RALLY, HONDA CTX700, HONDA DN-01, HONDA GB250, HONDA GROM, HONDA GROM
Easy installation on zx10r
Installed on Motorcycle as I am addicted to my phone.
RAM Mount's are easy to install.
Simply remove and replace the Bolt on the Stem.
It is equipped with a locking agent, so it takes a lot of strength.
View detail
Wish I had switched to this earlier.
It is TORQUE 5G and it is just the right size. Just by clamping it, even if it is a little rickety, it doesn't gap at all. It is as expected from Ram Mount. View detail
Universality
We selected this product to install Tire's wireless Air gauge Monitor.
The 1/4-20UNC screw for general camera use can be used.
There is no retightening component, so the angle must be adjusted after the Camera or other device is firmly screwed in.
View detail
Select Length
We selected this product to install Tire's wireless Air gauge Monitor.
The large handlebar may be difficult to tighten depending on the installation location and angle.
I chose the standard size without thinking, but the short size seemed to fit better.
You may choose Standard or Short by taking measurements of the mounting location.
View detail
racing (of an engine)
To install Tire's wireless Air gauge Monitor.
We chose this product, which uses Stem holes, because we did not want to increase the number of conspicuous Mounts.
I could not get the installation to work and when I repeated Cut, it went blank.
Instead of following the instruction manual, once the cut is made, the Stem hole should be filled to the Limit.
Tightening Bolt and expanding Body may work.
It will not come off, so it will be used as is.
View detail
Is there a mistake?
I couldn't believe my eyes at the difference between the statement and the merchandise.
What's his mistake?" I feel a little lost.
View detail
Excellent in both fixation and usability
At first glance, the 4-point rubber arm looks poor, but it fixes quite Firmly. In the past, when I was using a mount from XYNA, my phone flew off with a shock when I went over a bump, which was a tragic experience, but it has never happened after using this product. The other parts can be easily attached and removed without tools, so it is very convenient. View detail
It is probably the easiest way to attach and detach the phone.
I think this Smartphone Holder is the easiest and most stable way to put on and take off the Smartphone, and is suitable for those who frequently put on and take off their Smartphone while touring or taking a break. I just wish the price was a little lower! View detail
There was one for a Large-ish phone!
It has been about 18 months since I purchased Ram MountBody in September 2020. During that time, I used it about 1-3 times per month when Touring, and before I knew it, theRubber was shredded.
I had a feeling that it would break off at some point, since I had been stretching the Rubber as hard as I could to fit it into the largest one I could mount (iPhoneXS Max).
I had no choice but to replace only Rubber, so I pulled up the Ram Mount product list...?
Fa Brett." ? What does that mean? → I heard this is what they call the middle Size between a smart phone and a Ta Brett (I've never heard of it before). If my sma... Fa Brett." ??
So I bought this Size to try it out.
As it turned out, it fit perfectly!
I wonder if this Size has been around for a while? I'm glad I found it.
View detail
Mobile Holder
I bought this for navigation on my phone, but I read on the Net that the iPhone's Camera function can break down if it's fixed too tightly…
Not sure whether to use it or not.
View detail
Fits: YAMAHA NMAX, YAMAHA MT-07, SUZUKI GS125, KAWASAKI VulcanS, HONDA Rebel300, YAMAHA NMAX155, SUZUKI BURGMAN200, HONDA REBEL250, HONDA SUPER CUBC125
just right
I bought this product because I replaced the Handlebar and the Mount I was using before could not be installed anymore.
Installation was easy with the Mirror bolt.
I was able to place it in just the right spot so I could easily see my phone.
The product itself looks cheap, but the plastic part is thick enough to resist cracking.
View detail
For iPhone 11Pro max
I bought this to put on my motorcycle!
My iPhone is too large, but it fits perfectly.
It is easy to install, quick to remove, and comes with a rubber to prevent it from falling, so you can use it with confidence.
View detail
Fits: YAMAHA YZF-R3, SUZUKI GSX250R, YAMAHA YZF-R25, KAWASAKI Ninja250SL, HONDA CBR650F, KAWASAKI Ninja250, HONDA CBR250R, HONDA CBR400R, HONDA CBR150R, HONDA CBR500R, YAMAHA YZF-R3
It's not pretty. But it has the power to be omnipresent.
[How is it used?
When considered as a single product, the longest is less than 5 years, or about 60,000 km.
Drive in Touring or Circuit.
The mirror holder for NISSIN's brake master (YZF-R25, CBR-250RR), CF-POSH Universal mirror holder, YAMAHA 5YU-26393-00, and many others.
The Ram Mount is used in combination with a short arm and a smartphone holder to hold heavy objects such as an iPhone 12 mini, Xperia 5, Galaxy S21, and Driveman BS- 8.
Was the one you received as per Image?
In the Instruction Manual, there is a piece of Pole Rubber stuck to the base of the ball, and for better or worse, it's just like the Image.
Was the installation difficult?
Since the entire circumference is round and there is no flat surface to apply a tool to, the bolts can be installed with a right hand turn, but it may require some ingenuity to tighten them.
It may be possible to use a Clamp or a Monkey Wrench to hold it in place, but I'm using a Dustcloth wrapped in leather gloves to hold it in place, and then screwing it into the screw lock with all the screws dipped in it.
How was your experience with it?
There were no problems such as the ball falling out of the Bolt, the aluminum body cracking, loosening, or the Arm coming off, and the mounted devices are working fine.
[Included Parts:were they on?
Although it says that the screw lock is required, I'm pretty sure it isn't, so you'll need to prepare for it.
[Was there anything that disappointed you?
Nothing special. If you go to the store, you can see it, but it looks like Ram Mount, for better or worse.
It's an M10 1.25 Normal Thread Screw, which is the same bolt size as most Mirror holders, so it should be easy to install.
However, because the screw part itself is not that long, and because it is aluminum, and because it is difficult to remove, it is not good for tightening together.
On the other hand, since it has to be installed using the screw lock without any tools, it is better to think that it is difficult to remove it. I tried to remove it by squeezing it under the same conditions as when I installed it, but it didn't seem to budge.
It competes with Quad Rock and SYGN HOUSE, and as a product, it has lost quite a bit in terms of its beautiful appearance, but I have yet to encounter any irritating or critical aspects in practical use.
View detail
I wanted this.
In the case of a normal Arm, the direction in which the Arm moves in relation to the Base and the direction in which the phone moves in relation to the Arm are the same, so if you want to point the phone at yourself, even though it can swivel slightly, the mounting location is limited. However, if you want to connect two short arms with a ball, it will be very large.
I used to ride a Valkyries that had a large handlebar and windshield, so I was able to get away with it, but I switched to a Bolt that had a small handlebar and windshield, so I found this product when I was wondering where to install the Base. If not for this, I would have only been able to mount it in a way that would have made my phone stand out quite a bit.
The purchase price was 2530 yen. It has more parts than the usual two short arms (1320 yen), so I think it's pretty inexpensive.
View detail
As a matter of fact.
The tank cover is floating a little too much.
I bought it to physically hold it down (laughs).
Just the front part of the Cap.
But if I'm going to buy one, I'd prefer a Ram Mount product (laughs).
You can mount it in many ways. It's very promising.
In. I think.
Small size is marked for Honda.
It's definitely Large Size.
I don't know why it's happening, but...
Considering the size of the tank cap.
I know it's obvious.
That's the trap (laughs).
So. Of course it's not the M5 cap bolt.
I use the M6 and M4.
And if it's M6, you might want to widen the hole a bit.
That part of it is strange.
View detail
Purchase Repeat
I have been using it on my Ninja 1000 and found it to be sturdy and stable, so I decided to install it on my CUB as well.
Since the Meter visor with Bracket has already been installed on the CUB, the Quantity visor is installed on the Bracket part of the CUB.:Set
The U-shaped clamp came with two sizes, Large and Small, but the Small one was just right.
Quantity of all Arm and Mount (sold separately):When set, it is a little too large and tough for the CUB, but you can drive without worrying about it coming off!
Impressions of the Ram Mount purchase & darr;
https://imp.webike.net/article/453185/
Meter visor is this! ↓
https://www.webike.net/sd/24105239/
Meter visor imprints & darr;
https://imp.webike.net/article/505612/
View detail
I should have bought a new one sooner.
I used to use a U-shaped clamp type Base, but I had a hard time turning the nut when I fixed it to the Handlebar. It's not something I'm going to put on and take off that often, but I took the opportunity to buy a new motorcycle and replaced it with this Base.
I was able to attach it to the handlebar of the BOLT Shoulder Bag without too much trouble, even though there are few straight lines. I was able to finish the work very easily. I'm very happy with the way it looks after installation.
It would be nice if it was a little cheaper, but I guess that's what you get when you consider the strength and all.
View detail
For Large-eyed Smartphones
Purchased for spare parts.
I'm currently using one for a phone up to about 5-inches, but I've switched to a larger phone, so I'll replace it when it runs out.
I've applied a MAJOR amount to the image so you can see how large it is, if you want to check it out.
View detail
RAM MOUNT Ram Mount Long arm
Purchased for use with ActionCam View detail
RAM MOUNT Ram Mount Standard Arm
Purchase to attach Navigation and Camera
It's solid and safe.
View detail