Reviews
Fits: Others NISSINMaster cylinder tank cap O.D. 59 (some φ61)
Good texture
Cap replacement only, It is easy to install.
The quality is good and I like it very much.
I'm glad that it has a little accent and a custom feel to it.
View detail
Appearance Refreshing
Purchased to install Hazard switch on DL1000 V-STROM250SX
Hazard relay must be purchased separately
Switch has a Click feel and the controls are excellent.
DL1000 V-STROM250SX has a gap between the switch box and the master cylinder, so it is a just fit.
It is possible to install it in a narrow space, but when installing it on φ22.2mm Handlebar, it is difficult to wrap the rubber for Spacer, and it is a little frustrating to install.
WiringSleeve is not installed in the most conspicuous place, so it would look awkward if Wiring is installed as it is.
FlatSwitch has a Sleeve in it... I put the Wiring together using the WiringSleeve that was created when I trimmed the Wiring on the Hazard relay.
View detail
Fits: その他
RelayBody is slightly larger
Purchased to install Hazard switch on DL1000 V-STROM250SX
The wiring is long enough, so when installing the wiring, it was trimmed down to about 500mm and wired at the Bullet Type Terminal.
Wiring for Position is fixed with Bullet Type Terminal near BlinkerWiring.
I'll install the PositionLED Blinker one of these days when it comes out.
However, for the DL1000 V-STROM250SX, there is a Hazard kit (46234) from DAYTONA, and if you are worried about the wiring process, it would be better to choose that one.
I didn't like the supplied On/Off Switch Flat Face Type (40440 ), so I used a separate Slender Switch. [Flat Seesaw Type] (79339), but the price is about 1,,500 yen higher.
View detail
It would be convenient and easy to have it.
The area around the service power supply on the left side of Shinobazen's lower cowl is full of wiring, which may interfere with cowl removal, so we purchased this product in anticipation of future crisis expansion.
The most difficult thing was the location of the D-unit. Shinobu Sen has a space after the battery under the seat, but the bracket plate was in the way and it was not convenient to use.
The installation wiring is fine, and it will be able to handle additional equipment for a while.
What I have noticed is that
Need appropriate tools (Tester/Inspection TesterElectric Works Pliersetc.).
The Bullet Type Terminal is slightly different in size when connecting to a device, so it is necessary to match one of them.
The Power Supply Cable has become stiffer and tougher to handle in Plus.
The lid of the Case is hard to tighten.
View detail
Daytona usb 18w.Good
Type C usb.Bult qulity good.water proof.cable lenth inought for from head cowul to handle bar mount.good thing is out put port dust seal is replacibale.Main power supply cable along with mini barral fuse.Out pout usb c port is very tiny and simple mount with cable tie Unfotunatly my unit dosent work some time in idel rpm,I'm suspecting volatge detecting(even viltage above 12,4v )Any way im satisfied. Charging is good can be charge phone battery quickly. View detail
Fits: KAWASAKI Ninja250, KAWASAKI Z250, YAMAHA TZR50R, YAMAHA TZR50, YAMAHA TZM50R, YAMAHA TZ50, TRIUMPH TIGER1050, SUZUKI BURGMAN400, SUZUKI BURGMAN400, SUZUKI BURGMAN200, SUZUKI SKYWAVE400 burgman, SUZUKI SKYWAVE250 burgman, SUZUKI SKYWAVE250 burgman Type S, SUZUKI SKYWAVE250 burgman TypeM, SUZUKI SKYWAVE250 burgman SS, SUZUKI DR800S, KAWASAKI ELIMINATOR 125, KAWASAKI Z400, KAWASAKI Z400, KAWASAKI Z250SL
Used for city driving
It is used for city driving.
Controllable and good feeling. It is less scary even on rainy days. The price is not too expensive and I like it.
I will report again on durability.
View detail
It's not Kang Tan, right? LOL!
In the product name Kang Tan." but it is not such a kantan to be installed on ELIMINATOR 400.
I don't mean difficult, I mean tedious lol.
To begin with, the problem is on the body side, but the Tank has to be removed in order to install the 4-poleRelay.
This is a pain in the ass, lol.
The product itself is solid, and the Harness fits inside the MeterCowl, so it is a good reflection.
I think it will be around the Handlebar when the retrofit USB Socket is installed, so it will be easy to handle the Wiring! (,,> <,,)
As mentioned earlier, the product received a perfect score except for the 4-poleRelay installation.
View detail
A little heavy?
It is no longer a standard product. lol
The drawback is that the Material is heavy because it is steel.
Backrest and Engine Guard and Quantity sold by the company for ELIMINATOR 400:A whopping 10kg increase when installed with 1 Set of 3-items!
It's not only the push/pull, but it also affects the ride a bit! That's what I'm thinking. (Polish)
However, it is a must-have item to attach the side bag, so it is attached.
The product itself is well made and has a nice paint job.
It does not seem to be Rust if you don't scratch it.
If the material was Stainless Steel or something like that, I would give it 5 stars. (Polish)
View detail
A little relief on rainy days
I had only used the Net type, but after using it, I was impressed with the convenience of the Large type.
Loaded cargo is inconspicuous
No gaps to protrude
Large sturdy enough for a little bit of rain.
More compact than Net type when stored
I bought a Large size thinking that a Large would also be a Small!
Can wrap a full size helmet completely.
View detail
Fits: HONDA CB400SS, HONDA CBR400F, HONDA CBX400F, HONDA CBX400F, HONDA GB400, HONDA REBEL, HONDA REBEL, HONDA CB400SF, HONDA CB400SF, HONDA CB400SB, HONDA CB400SF HYPER VTEC Revo, TRIUMPH STREET TRIPLE, TRIUMPH BONNEVILE, TRIUMPH SPEED TRIPLE S, MV AGUSTA BRUTALE750S, DUCATI M400S, DUCATI M400METALLIC, DUCATI M400DARK, DUCATI M400DARK, DUCATI M400
etc., etc., etc., etc., etc., etc., etc., etc. (p∀p) aha!
[How is it used?
After about 2 years of use, my Cover finally tore and was no longer able to withstand normal use, so I decided to purchase one.
Was the one you received as per Image?
It was just as in the Image! Thanks for the heat resistant Seat!
How was your experience with it?
It is also good in the rain without letting it through properly!
[Points to note]
I have used Seats in a variety of price ranges, and have concluded that Balance is good for use in uncovered Blue Sky parking, replacing a few thousand yen price range every few years.
Elastic band is used to keep the Seat from flipping up in high winds.
How did it compare to other products?
DAYTONA is one of the manufacturers we trust, and they also sell Garage.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
The holes for the front and rear tire locks are also good. I have never used it (laugh).
View detail
I love it
I didn't expect so much because of the low price, but I liked them because they have a better texture than I expected and they are Side GoreType, so they are easy to put on. View detail
Fits: YAMAHA VMAX , HONDA FTR223, KAWASAKI GPZ900R, KAWASAKI KSR-1, KAWASAKI KSR-2, KAWASAKI ZRX1100, KAWASAKI ZRX1100II, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZZR400, YAMAHA VMAX, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MAJESTY250(4HC), YAMAHA YZF-R1, YAMAHA YZF-R25, YAMAHA YBR250, YAMAHA YZF-R1
Cospar good
Since it is DAYTONA, it is safe.
It is more subdued in appearance than other Mesh hose.
Banjo bolt and Washer if attached.
It was even better.
A is Straight and 20 degrees though,
I would have liked to have had 20 and 20 degrees if possible.
View detail
Fits: KAWASAKI Ninja1000, KAWASAKI Z900, KAWASAKI Z800, KAWASAKI Ninja1000SX, KAWASAKI Ninja ZX-6R, KAWASAKI Ninja650, KAWASAKI Ninja400, KAWASAKI Ninja250, KAWASAKI Ninja ZX-25R
It is easy to install. and the visibility has increased!
It is easy to install. and it gives me a wider field of view and helps me when changing lanes. one drawback is that it is not easy to remove. View detail
Fits: Others Universal
I wanted something inconspicuous.
Reflector is now required for installation of KOSORear Mudguard KS-MGXF-01.
We chose this product because it is not assertive and prevents the License Plate from bending.
Reflector was replaced with KIJIMA Reflector Slim 3, part number 305-2146.
KIJIMA Reflector Slim 3 can be installed without modification, and both the reflector included with the product and KIJIMA products are secured with M5 Hexagon Nut.
We believe that measures to prevent loosening of the Nut are necessary.
There are several ways to prevent nut loosening, but in my case, I use Nylon nut (something like Self Locking Nut) I used the
View detail
Fits: HONDA AX-1, HONDA CB250F, HONDA CB250R, HONDA CB400SS, HONDA CBR250R, HONDA CBX125Custom, HONDA CBX125F, HONDA CBX250RS, HONDA CBX250S, HONDA CL250, HONDA CL400, HONDA CRF250L, HONDA CRF250M, HONDA CRF250RALLY, HONDA CRF250L, HONDA CRF250RALLY, HONDA FTR250, HONDA GB250 CLUBMAN, HONDA GB400TT, HONDA GB500TT
Stable and secure.
Since I once bought a cheap Chinese Other Brand Product on Amazon and had a large failure, I have chosen this one from DAYTONA, which I can use with peace of mind! This time, I bought it as Single Item, but the Washer and O-ring Quantities are available.:Set products are convenient. View detail
Fits: YAMAHA WR250X, YAMAHA WR250R, YAMAHA XJR400RII, YAMAHA DIVERSION, YAMAHA XJR400R, YAMAHA XJR400R, YAMAHA XJR400S, YAMAHA XJ400ZE, YAMAHA XJR400, YAMAHA XJ400Z, YAMAHA XJ400ZS, YAMAHA XJ400D, YAMAHA XJ400S, YAMAHA XJ400, YAMAHA SR400, YAMAHA FZR400RR-SP, YAMAHA FZR400RR, YAMAHA FZR400, YAMAHA FZR400R, YAMAHA FZR400
SUPER SPORTS750Middle to Exactly
ExactSize for YZFR-7, CBR250RR, etc. Can also be used loosely for pcx160.
Ventilation in the Mirror position provides excellent heat exhaust and prevents heat buildup even in the summer.
View detail
Silver insert color is nice.
Installed in conjunction with Grip replacement.
Since the motorcycle has many plating parts on the body, silver was selected as an accent to the handlebar's black.
The color is good and the Silver looks good.
We considered heavier products, but chose this product with less thickness considering the width when parking.
View detail
Looks are the top priority, so it is very Parenthesis good!
I usually wear 26.0-26.5cm, but these boots were too tight for 26.5cm, so I decided to go with 27.0cm, which is a little larger. I would not have bought it without the Fastener. Still, because of the slim design, I had to open the fastener all the way by hand to get my foot into the Smooth.
The fastener cover is also very nice, as it prevents the frame of the motorcycle from being scratched by the fastener, which is not necessary if the fastener is on the outside of the boots, but it is a bad parenthesis.
I thought the toe part had a built-in Shift changeGuard, but it does not. That said, the leather is thick enough that my thumbs did not get sore after 3 hours of driving 120km or so on a mountain pass.
I heard that there is a Protector in them, but I am not sure because they are not thick enough.
The looks are outstanding and this is a traditional NAKED to ride with. (GB250 CLUBMAN) It is the best Fit for the "I", but the functionality is secondary. The soles are not very thick, but they are hard, so quick movements are not a strong point.
View detail
It is highly windproof, so it is a recommendation for those who are worried about running wind measures.
Even with a full face or system helmet, the riding wind coming in through the neck will chill the neck and nape of the neck. This can cause loss of energy and distraction, so it is important to prevent wind from entering the neck, wrists, and ankles as much as possible.
Windproof Neck warmer is also effective in keeping out the cold to a certain extent, but it is quite difficult to shut out the driving wind that invades the Helmet. It is not always possible to fill the gap between the helmet and the neck well, and when you shake your head to look behind you, it can twist and create a gap.
So I bought a Balaclava-shaped full face mask, thinking that it would completely protect me from the driving wind. As a result, I almost achieved my goal, but since the wind protection effect is only on the front side, the fabric gradually cooled down by the wind around my neck, and the area around the nape of my neck started to get cold. Also, when I looked back, there was a gap around my collarbone due to the Gap.
Still, it will eliminate the direct contact of the running wind with the skin, so it will work just as well. Hopefully, a little (500 yen) I would be willing to pay a little more if the price goes up by about $3.00, so I would like to make the entire Neck section windproof and a little more. (about 5 cm) If you could make it longer, there is nothing to say. So I will give it 4 stars.
View detail
Just fit for Traditional NAKED!
My middle finger length is 8cm and palm length is 11cm (19 cm in total) So, L Size is almost Exactly, but not so Tight, so thin Inner Gloves can be used.
As DAYTONA's goal, the design is just right for the traditional NAKED. The shirring on the outside of the fingers is stylish.
The sewing is solid, the leather has a good texture, and the palm is slightly suede-like, which makes the Grip less slippery.
It seems to have a thin padding, but since it is a Short Type, it will not be usable in midwinter. Also, there is a light punching processing, but it cannot be used in mid-summer, and even so, it can be used until early summer. Therefore, I think that these are the Gloves that will be used for the longest period of time in a year, though they are used in 2Season from early spring to early summer and from early fall to early winter.
View detail