Reviews
Reduced vibration sensation
Replaced from YB125SP OEM.
With OEM, we replaced it with this Clip to deal with the vibration when the Speed continues over 60km.
It is comfortable to the touch even with bare hands and does not slide around too much even with gloves, so it is very easy to use.
The crucial vibration is also clearly reduced compared to the OEM, and the effect is likely to be felt even during long hours of touring.
View detail
Great cost performance!
I was looking for a Grip to install on my WhiteBlueGLADIUS650400 and found this.
The straight line design fits well with GLADIUS 650.
The grip is nice and moderately soft.
I have not run the distance yet, but I think it could be compared to PROGRIP.
This is a satisfying experience for a purchase price of a little over $1,000.
I can recommend it
At any rate, I have ordered another pc. in a different color.
View detail
Exquisitely shaped Barrel Style Grip
We also use other products from the GRIPPYGRIPSeries and
I try to Check when a new Type is released.
I didn't notice it until I actually held it, but it is actually barrel-shaped.
The thickest part is just under 35mm, and the thinnest parts are just under 33mm, loosely taper to the ends.
Barrel-shaped barrels are not a good match for SportsNAKED, as they give a strong impression of classicism.
This product was not uncomfortable to install because the raised area is very slight.
The accuracy is not good, but if you draw a line on the photo, you can see that it is almost Straight shape.
Active:Elastomer TaperGrip
https://www.webike.net/sd/23817728/
domino:Road Type Grip
https://www.webike.net/sd/21649162/
I have also used a simple Taper shaped Grip of the Sports Type as shown above.
The thinnest part where the thumb rests is thin-walled.
Vibration isolation performance tends to be poor, and it is necessary to keep gripping the Axel to maintain the Axel opening.
Avoid the slender part and hold a little outside, etc. Otherwise, you will be fatigued.
This product has a thick enough wall even at the thinnest part to prevent fatigue.
The Center portion is thick so that the Axel opening can be maintained by lightly pressing the hand against it without a strong grip.
The feeling of the Clutch and Throttle operation changes depending on the position of the force applied.
If you are conscious of adjusting the position of your thumb when starting and cruising
The grid-shaped mold grips firmly, requiring minimal gripping force.
I was concerned that the DAYTONA Logo was so large that it was ruining the GridDesign.
This Logo is only on one side, so it can be rotated 180 degrees and installed in a different orientation.
It retains a more classic appearance, but I would have liked it to be in a more discreet position.
(★-1)
This time I installed it so that the Logo is on the top side, but next time I will turn it to the back side.
Also, it is a fluffy RUBBER in both good and bad ways, so the corners round off quickly.
It is not Level wear that makes it immediately unusable, so it is not necessarily less durable, but
Performance at the beginning of use may not last long.
I'm going to move away from this product impresion, but the same GRIPPYGRIPSeries
Especially for two-color molded Type, the deterioration in usability is noticeable before the appearance.
View detail
For the price they are good
Easy to install, with an arrow on each end indicating "up". The deep red/ ox blood colour is quite a nice red. They do seem a little thinner than the oem grips & somewhat softer too. I do like The grip pattern, but I suspect the rubber may be prone to wear.. but time will tell. I think my black leather gloves have blackened the grips a little as can be seen in the photos I've uploaded. View detail
shock
I learned that what I had been using was just Rubber.
After using this, I have no confidence in using any other Grip.
Fit as if absorbed into the palm of the hand, with sufficient cushioning to prevent fatigue.
A non-habitual design that can be attached to bobber, chopper, caferacer, etc. regardless of genre.
Recommended
View detail
Good price and appearance.
[How is it used?
Mainly Touring
Was the one you received as per Image?
It was just as Image.
How was your experience with it?
I guess it's a preference, but after about 30 minutes the unique unevenness starts to bite into my hands and become uncomfortable.
Good design, but not comfortable to hold.
How did it compare to other products?
After some use, I will change to Pro grip.
If you care about looks, it's Recommendation, but not much functionality.
View detail
katana
Among the many grips, I still chose a katana with a story. Looking at it in person, the black and gray colors match well. It's not hard, but it's so soft that it doesn't seem to have a short shelf life. The throttle length is 125mm, but it's actually shorter. It doesn't seem to be that important. I bought the 3 pieces together as a set and they fit perfectly.
But I can't upload photos. Why doesn't it work? ------------------------------------------ ---------------- Of the grips, I chose a Katana with a story, and I saw the black and gray color. It doesn't seem very important. I bought three components with a set. But I can't upload a photo. Why can't I Powered by Google Translator
View detail
Rear Fender looks beautiful.
It is lightweight, easy to grip, and extremely easy to install!
Most Z900RS owners install a Grab Bar that goes around the Rear Fender.
In such a situation, I bought it thinking that it could be different … from others. I am satisfied.
View detail
Lightweight and easy to grip
Lightweight. Easy to install. The only thing is that the texture is a little cheap. It would be useful if it were to cause a problem when in a store. View detail
High Quality Grip
These Daytona bar grips are possibly the best finished grips I have ever purchased. The finish and molding is excellent. They have a good grip pattern like Renthal, but are far better quality. Not too hard or soft in Black. I have used many makes of grip such as Renthal, Progrip etc and these are even better quality... View detail
Comfortable and Stylish
The ergonomic shape makes riding more comfortable and non-slip texture is great even without gloves. Matches perfectly with Daytona Bar ends and mirrors. View detail
Second Repeat purchase.
This is my second Repeat buy Grip!
It is installed on REBEL250
Very comfortable to drive with a very good grip.
It lacks a little durability, but for the price of the Gold, it is sufficient.
Fits snugly without a grip bond.
View detail
Comfortable grip and does not get caught on the Gloves when closing the Throttle
Used for NSR50.
Super high throttle kitRepair parts made by DAYTONA, but can also be used with normal throttle.
When closing the throttle during circuit driving, the grip is not so good, and the gloves are not so tight.
There were times when I got stuck and could not return Throttle to Smooth.
The design of this product is comfortable to grip, partly because I am used to the old design,
The above no longer occurs.
I am sure to Repeat next time.
View detail
Yawame's Grip.
It is a grippy gripper with a moderate gripping force.
I chose it because of its design!
Grip is consumable, so feel free to give it a try!
View detail
Design, Grip◎ and high cost performance!
[How is it used?
Since the normal grip was getting old, we wanted to renew it with a shape that would not tire us out over long distances, and we found this grip with a softer grip that is more comfortable to hold.
Was the one you received as per Image?
The shape and quality were as per Image.
The length was not as short as I expected compared to NORMAL, about minus 5mm.
Was the installation difficult?
First of all, Quantity:Pair (for Left and Right) but check theQuantity:Pair (for Left and Right) Since it is not a symmetrical cylindrical shape, mistakes are unlikely to occur. Even if you are not sure, you can recognize the Throttle side by looking at the shape of the hole, which is slightly wider than the other side.
The installation was tight only for the new grips, and the insertion was quite large and strange.
I screwed in the handlebar and grips while spraying CRC, and while the Throttle side went easily, the Blinker switch side was particularly tough.
And because it is slightly shorter than the Normal grip, I diverted the for Motorcycle grip lock and used it instead of the Spacer.
How was your experience with it?
The slight Ergo shape makes the grip comfortable and less tiring over long distances.
I feel that dirt will accumulate on the unique Dimple, but I am satisfied with the Coloring as I was able to match it with the Tank color.
[Included Parts:were they on?
Pac Cage ONLY and no other.
[Was there anything that disappointed you?
This Grip has an overall length of 122mm, which is about 9mm shorter than the NORMAL, and I wish it had the same length, but I wanted it to be at least 125mm, which is a common Size.
▼It would have been nice to have a Lineup with different overall lengths for each Motorcycle Size.
View detail
ปลอกแฮนด์ daytona ทรงสวยใส่แล้วกระชับมือดี View detail
Used on GPX750R
I like it because it matches the color of the car easily. I am afraid that the black rubber part on the outside will peel off soon, especially if I don't have an air compressor to remove the old grips. View detail
Expected
The texture and ease of installation were as expected. View detail
We have it all at DAYTONA.
It's neither good nor bad
gRIP
View detail
Fits: KAWASAKI Ninja ZX-25R, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R SE KRT Edition, Others
usually
I like DAYTONA's PremiumZoneSeries and have a lineup of them.
There is nothing particularly wrong with it, but there is nothing particularly appealing either.
View detail