Reviews
Exquisitely shaped Barrel Style Grip
We also use other products from the GRIPPYGRIPSeries and
I try to Check when a new Type is released.
I didn't notice it until I actually held it, but it is actually barrel-shaped.
The thickest part is just under 35mm, and the thinnest parts are just under 33mm, loosely taper to the ends.
Barrel-shaped barrels are not a good match for SportsNAKED, as they give a strong impression of classicism.
This product was not uncomfortable to install because the raised area is very slight.
The accuracy is not good, but if you draw a line on the photo, you can see that it is almost Straight shape.
Active:Elastomer TaperGrip
https://www.webike.net/sd/23817728/
domino:Road Type Grip
https://www.webike.net/sd/21649162/
I have also used a simple Taper shaped Grip of the Sports Type as shown above.
The thinnest part where the thumb rests is thin-walled.
Vibration isolation performance tends to be poor, and it is necessary to keep gripping the Axel to maintain the Axel opening.
Avoid the slender part and hold a little outside, etc. Otherwise, you will be fatigued.
This product has a thick enough wall even at the thinnest part to prevent fatigue.
The Center portion is thick so that the Axel opening can be maintained by lightly pressing the hand against it without a strong grip.
The feeling of the Clutch and Throttle operation changes depending on the position of the force applied.
If you are conscious of adjusting the position of your thumb when starting and cruising
The grid-shaped mold grips firmly, requiring minimal gripping force.
I was concerned that the DAYTONA Logo was so large that it was ruining the GridDesign.
This Logo is only on one side, so it can be rotated 180 degrees and installed in a different orientation.
It retains a more classic appearance, but I would have liked it to be in a more discreet position.
(★-1)
This time I installed it so that the Logo is on the top side, but next time I will turn it to the back side.
Also, it is a fluffy RUBBER in both good and bad ways, so the corners round off quickly.
It is not Level wear that makes it immediately unusable, so it is not necessarily less durable, but
Performance at the beginning of use may not last long.
I'm going to move away from this product impresion, but the same GRIPPYGRIPSeries
Especially for two-color molded Type, the deterioration in usability is noticeable before the appearance.
View detail
For the price they are good
Easy to install, with an arrow on each end indicating "up". The deep red/ ox blood colour is quite a nice red. They do seem a little thinner than the oem grips & somewhat softer too. I do like The grip pattern, but I suspect the rubber may be prone to wear.. but time will tell. I think my black leather gloves have blackened the grips a little as can be seen in the photos I've uploaded. View detail
Used on GPX750R
I like it because it matches the color of the car easily. I am afraid that the black rubber part on the outside will peel off soon, especially if I don't have an air compressor to remove the old grips. View detail
My Favorite Grip
Finally a grip that doesn't chew my hands. It's a great feeling, I'm definitely getting used to it, but it's a great raw feel to the bike, I feel more connected. The best grips money can buy. super soft without sacrificing longevity. I like them so much, I put them above everything else. These are the only handles I use, super grip, durable and slim design. They also hold really well with the grip adhesive, no safety wire needed if installed correctly. A+++ product... View detail
Fits: KAWASAKI Ninja ZX-25R, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R SE KRT Edition, Others
DAYTONA is the best!
The grip is not too tight and feels very good.
It is a little softer than NORMAL!:Pair (for Left and Right) Exchange with Lever!
It was not too difficult, and even an amateur like me could do it easily.
View detail
Grip for city driving and touring
I was looking for a Grip with Yellow color insert to match MotorcycleBody.
ProGrip had a similar atmosphere, but
We chose this inexpensive option because we were not particularly concerned about performance.
It is soft and seems to have high QUALITY for the 1000 yen price range.
The molding Gold mold? The mold itself seems to be new and there was no BALI or distortion visible.
I think the product is better than a poor Longtime seller's Grip.
It is made softly, so you can imagine the feel of a ProGrip type.
Vibration absorption is not bad.
Attach it so that the colored part is in front.
It is difficult to see in the product photo, but the rugged part is more difficult to see than the colored part.
The circumference is long and bulging.
Therefore, the cross-section of the Grip is not a circle but an oval.
This shape makes it easy to turn on/off Throttle like Stop & Go, but it is not easy to turn on/off Throttle like Stop & Go.
It is not suitable for SportsRide because it is difficult to fine-tune the Throttle, and I think it is suitable for city driving and touring.
Also, the uneven areas are not soft and angular, so use on off-road or other dirty premises is not recommended.
DAYTONA's GRIPPY GRIPSeries is not only oval in shape, but also taper and ergonomic for long bicycle rides.
I think people like or dislike the shape, but I thought it was only possible for Large Hand to offer a rich lineup of color schemes and designs.
Of course, there is also the Wiring ditch.
I would like to try another design.
View detail
My HeaterGrip broke so I went with this Grip. It feels softer.
It feels soft. It is easy to grip. View detail
superior article
It will be perfect for the rider of KATANASeries, and it became a good atmosphere by changing the color of Bar End to Gold on White. View detail
good for its price
Design with Hexagon Nut as Motif
Recommended for those who like to feel a little different from others.
The grip is a little thinner than OEM, but it's ok.
View detail
Triumph.
For inch bar Sports-type PenetratingGrip less!
For HARLEY? it's all Plating decorations and Billet systems.
I bought it to try it out.
It's barrel-shaped.
The texture is good, like a soft silicon sponge.
As for the grip...it would be best if it was just a little bit thicker overall.
Is it not expected to be tactilely durable?
Well, it's cheap, so I'm mostly satisfied. If it were a little thicker, I'd get a perfect score.
View detail
Inexpensive.
Quantity:Pair (for Left and Right) Single Body for sale, but Quantity:Set purchase is less expensive than the OEMSide grip; Design is less rounded and less overhanging RefreshingDesign. functional aspects by the aforementioned Spec. (handle) It's not as good as the original, but it's a good product if you think of it as a dress-up and practical use. It's easy to install and easy to use. View detail
Fits: KAWASAKI Ninja ZX-25R, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R SE KRT Edition, Others
The design is subtle, but I thought the functionality was good
My 30 year old motorcycle Grip, which I usually use, has been worn down by Large and the vibration Because of the Large size, I bought this Grip which happened to be on sale at a discount I didn't like the design, but there is not much variety of Grip in 125mm size I bought this one I used detergent to lubricate the rubber to make it soft It is very comfortable to ride and the vibration in your hand is less than the previous one It is now possible to View detail
Fits: KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R SE KRT Edition, KAWASAKI Ninja ZX-25R, Others
thin
I changed from the PROGRIP Because it is thin than the previous Pro grip, vibration absorption is a little inferior impression although the look is good Originally the Grip diameter is thin because it is attached to the Handlebar to widen the small worm If you like a solid feel, you'll like it A soft one with a soft grip seems to be the way to go Installation is easy to get in with soapy water and percri View detail
Fits: KAWASAKI Ninja ZX-25R, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R SE KRT Edition, Others
Comfortable to grip
Replacement from MONKEYFI's OEM Grip
I chose it because it had high word of mouth ratings
The grip is comfortable and satisfying
Cut the Bar End part to use the OEM Throttle
View detail
Fits: KAWASAKI Ninja ZX-25R, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R SE KRT Edition, Others
good
I went with the red colored Grip with lines! I wanted to buy it in a different color I wanted to get the other colors as well View detail
It's longer than the OEMs, but it's less noticeable
For practical purposes, I want the Assist Grip to be able to use the Racing Stand and push/pull the car body but
He said he didn't want to destroy the modern and refreshing Custom design I thought
At first, I was planning to paint the OEM PlatingGrip in black
I decided to go with the Black Grip from DAYTONA
Refreshing even when viewed from the side because it has one less bend than the OEM, and the effective length I'm also happy with the longevity of the product
However, the front side Grip attachment is very, very cheap and not very tactile
Aluminum with a skipped head of POSH Machining Net Ankor A combination of spacers
I tried to devise the attachment part (I also shaved off some of the GripBody to match it
The drawback is that, like the OEMs, the price is too high for Parts of this magnitude
Paint on the weld area is also weak, so the quality of the paint is not as good as it should be:I did not do 5pcs (I did touch up the paint.)
View detail
Fits: KAWASAKI Ninja ZX-25R, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R SE KRT Edition, Others
It is Opened End Type
I bought it because I wrote Closed End in the item description, but I was Penetrating.
A separate Grip end is required.
Although I thought that the photo was Penetrating, I thought it was useful, I trusted the explanation.
Let's order from Manufacturer yourself, etc..
View detail
Fits: その他 , HONDA Rebel 500, HONDA Rebel 250, HONDA Rebel 250, HONDA Rebel300
It has ridden on the dragstar classic. It attached simultaneously with handle exchange and carried out. comparing from an authentic positive one for me -- a grip feeling -- good . Classic touch is also pleasing. Since it is consumable good
It has ridden on the dragstar classic.
It attached simultaneously with handle exchange and carried out.
comparing from an authentic positive one for me -- a grip feeling -- good .
Classic touch is also pleasing.
Since it is consumable goods, there is no telling till when have, but I think that I will also make the next into this.
View detail
Fits: その他 , HONDA Rebel 500, HONDA Rebel 250, HONDA Rebel 250, HONDA Rebel300
In the grip for 1 inches, they are budget prices. A classic atmosphere is also Good!
In the grip for 1 inches, they are budget prices.
A classic atmosphere is also Good!
View detail