Reviews
Fits: KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z400FX/Z400J, KAWASAKI ZEPHYR400, Others CRcarburetor, Others FCR Carburetor Bodycarburetor
Good and close to OEM. I would purchase again.
Good and close to OEM. Would buy again. View detail
Used to return air from Tokyo TowerImpulse's Fuel Tank and carburetor
I was looking for a replacement for the OEM Hose since it was discontinued.
I was looking for an Oil Resistant Hose with an inner diameter of 5mm and a thicker outer diameter, and this Universal Product came to my attention.
Needless to say, the reason for making the external shape thicker is so that the hose band can be tightened more effectively.
I used the OEM 8mm outer diameter and attached it.
I would like to use it for other Motorcycle Repair as it is very cost effective and I have some left over.
View detail
Fits: KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z400FX/Z400J, KAWASAKI ZEPHYR400, Others CRcarburetor, Others FCR Carburetor Bodycarburetor
Not bad to look at.
It is inexpensive, but not badly made. Durability does not seem to be a problem. View detail
Fits: HONDA CB400FOUR (water-cooled), YAMAHA XJR400R, HONDA CB400SF, KAWASAKI ELIMINATOR 250, KAWASAKI GPz400F/F2, KAWASAKI Z400FX/Z400J, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYRX, KAWASAKI ZR-7/S, SUZUKI BANDIT250, SUZUKI BANDIT400, SUZUKI GSX250S KATANA, SUZUKI GSX400S KATANA, SUZUKI GSX400, SUZUKI GSX400, YAMAHA XJR400R, YAMAHA XJR400, HONDA CBX400F, HONDA CBR400F, HONDA CBR250R
No exhaust leakage.
Used for Exhaust System replacement. The work was completed without any exhaust leaks. View detail
Solid for the price.
The KSR80 from Tank to Carburetor is exactly this delicate size. To be honest, it is so long that it does not need to be this long.
The included Clip is almost useless as it does not spread out.
View detail
Is it cheap enough?
I bought it at a good price because the Lever area was getting a bit worn out.
Installation is easy as you just remove and replace it.
The problem is when you take it out of PetitPetit.
From the moment I opened it, there was a Wound in Lever's grip, and when I looked at the back, there was a spot where the base of the genus Gold was showing.
The paint is sparse and the visible area around the Mirror installation is crumbly and muddy.
Even though it is made overseas, TensionDown from the moment I saw it.
Is it called Short Type? Is it? The grip is shallower than the OEM Product I have been using.
I turned the adjustment screw a lot and finally completed the adjustment.
It's fine for use, but it's worth the price.
View detail
Fits: HONDA CB400FOUR (water-cooled), YAMAHA XJR400R, HONDA CB400SF, KAWASAKI ELIMINATOR 250, KAWASAKI GPz400F/F2, KAWASAKI Z400FX/Z400J, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYRX, KAWASAKI ZR-7/S, SUZUKI BANDIT250, SUZUKI BANDIT400, SUZUKI GSX250S KATANA, SUZUKI GSX400S KATANA, SUZUKI GSX400, SUZUKI GSX400, YAMAHA XJR400R, YAMAHA XJR400, HONDA CBX400F, HONDA CBR400F, HONDA CBR250R
Gasket
There is no exhaust leak and it works normally. View detail
Surface treatment is not complaint
After repeated standing jostling with the XELVIS, I discovered a crack at the base of the Clutch lever.
I was surprised to see it like that for the first time, but of course the OEM is out of print, so I bought this one from Universal.
Installation was fine. "Surface is not Beauty. The terminal shape of the Clutch switch is also the same as OEM.
However, I am concerned about the rattling of the Lever mounting part.
View detail
Cospa is good (・ω・) b
I needed the Filter in a hurry.
I was hesitant to buy from a famous manufacturer because of the high prices.
I found this product and made an instant decision!
It looks and feels as good as the famous Manufacturer's products.
I'm happy with the performance.
The rest of the story is still to be seen as it was just purchased.
Repeat plans if it's durable. (Translated; ω ´) no
View detail
We're doing a good job for our price
The RAMAIR Filter I was using originally became useless, so I replaced it with this one
The hole is so small that you need to widen it when you install it to cover the funnel You may need to make a small cut in the funnel
RAMAIR and Setting remained the same
The RAMAIR is more durable
The RAMAIR was useful for about 5 years, but this one fell apart after 2 years
Right now it's still Funnel
I think it's a good idea to have it as a precaution against vehicle inspection
View detail
Enough for occasional use
Not suitable for frequent use
The finish is rough and even looks like it might injure you if you use it with your bare hands
However, if you are an individual Youth and cut a cheap Chain a few times a year at most, it's enough for you There is safer than flying Pin's head off with a Thunder
Cost performance is Number one
View detail
It is cheap and good
I used it as a blowby hose
The Hose was soft and easy to handle
I bought it for the price as it is not a prominent place, but it was sufficient for my needs
However, it's industrial-mechanical design makes it unsuitable for a prominent location
View detail
But for those who only think about Cut
Seal chain to non-seal (Clip equation) The purchase is only to change the
This Cutter can cut the Chain once, discard the original Chain, and
This is an item for those people
It's cheaper and better if you just want to cut it, but if you want to use it repeatedly
Buy another luxury item
The quality of the Chain Pin extruding rod is poor and the shaft is straight in a blur
Can't press Pin
Probably the bar is only at the lowest level of strength, and if the pin is hard, it will break easily
So, shave the head of the Pin until it is flat before using it
When you say it's worth the price, you can say it's a product that requires a lot of dedication and determination
By the way, the handle is just stuck on the standard screw, so it's not as long as the appropriate length
If you stick a bolt in it and use it as a handle, you can hang a lot of power on it
Most of all, though, Cutter's Stick can't stand up to its power
View detail
Functionality good, Cost good
As described in the product description, it has a textured finish, probably due to bad casting sand
But it works fine
The ease of use is the same as other high end manufacturers, etc
Then cheap is a good thing! 。
View detail
Huh ha Gap is there ... really it is star Zero
Used for SA16J JOG.
Result ... Can not use. It was nearly an Objection place. If you buy this, Emon's 4-pole Relay is sure. After all, I repaired using EmonRelay.
View detail
It may be a shame feeling
I installed it in CR Carburetor, but when opening Axel to accelerate
It is likely to be stalled and it is difficult to run
Sponge's eyes are too fine to become resistance
View detail
It is enough to consider frequency of use.
Removed from the Gold mold of the casting and processed as it is.
However, Chain's Piece packing etc etc. How many times a year do you recommend? This item is recommended for those who can use it by all means.
It is better to buy the famous Manufacturer's Cutter.
Bush-born casting → BALI taking surface by yourself Buffing → Self-made finish
It is particularly recommended for people who can enjoy saying like this.
View detail
Spec. Ambiguous & Coil Consumption current excess Large
I tried to use it for Yamaha 3KJ JOG, but the 7 A Fuse just after Battery flew.
Spec. Because it is not explicitly stated, I do not know whether it is a broken item or not.
It became a loss of money purchase.
View detail
For vehicle inspection!
In direct carburetor it does not follow the vehicle inspection so purchase with vehicle inspection measures
RAMAIR and Green Light Sponge etc though it is a consumable. I used it, but the price is high but it is a difficult point
Vehicle inspection every exchange will ride with direct carburetor as expense gets truly as expected.
For those who wish as long as the vehicle inspection can go through, this product can be installed with this product
Just a pretty small size Size So it is a Large type car and it is in good condition Pants
Durability is only for use at the time of vehicle inspection so our case
Because it is crammed in Zip lock to prevent aged deterioration
It can be used permanently.
We are recommending because it is superior to COSPA
For regular use RAMAIR is recommended for every inspection by vehicle inspection (FunnelSpec. It does not mean that)
View detail
Necessary and sufficient
I tried several times to Cut of 520 Chain. I used it after scraping one side of Pin at Grinder once, but it will be free without difficulty. I do not understand the long-term durability, but it is not frequently changing such as Chain and this is enough for AmateurUser like me.
The item was washed and packed in PetitPetit in dry condition and delivered. It seems that improvement that it reaches with covered oil is improving.
View detail