Reviews
relatively large texture
I think the quality of the product itself is better than the price.
The size was larger than I wanted, so I sold it without installing it this time.
View detail
exchange
I was using Blinker by replacing it with LED, but it seems that it sometimes does not blink due to vibration, so I replaced Relay with a new one.
The price was not that much, and after the replacement, it blinked without any problem, which was helpful.
View detail
For replacement of old OHLINS.
Free Rubber
I don't know how long it will last.
View detail
Moderately
The threaded part is wobbly and not of very good quality.
I can't complain because of the low price, but it is not something I would confidently recommend to others.
View detail
It is cosy depending on how it is used.
Used in O/H of FCR Carburetor Body.
However, if the Float is soaked in Gasoline, it will expand slightly, so you will need to dry it out and wait for it to return to its original state, or make other adjustments when reinstalling it.
View detail
Bending changes Large
I have no complaints about the quality or the number of pieces. I think the price is also reasonable for this product.
However, it is extremely difficult to process One Side, which is Straight, into a Hook shape with just the right length.
It is impossible for an amateur to bend them into Beauty with pliers or other tools included in a normal Tools Set.
View detail
Fits: YAMAHA XJ400, YAMAHA XJR400R, YAMAHA XJR400R, YAMAHA XJ550, YAMAHA XJ400, YAMAHA XJR400
CherryCarburetor Float Packing
OEMs are too expensive to buy, so if you're not sure...
Cherry has found a Float packing that she has been putting out!
It's a Commendation because it's reasonably priced!
So far, no leaks, etc.!
View detail
For vehicle inspection.
Blinker is Clear Lens and was purchased for vehicle inspection.
I was concerned about the quality of the product since it was very inexpensive, but the light came on without any problems with regard to use.
However, I think it is closer to Red than Orange.
View detail
Fits: KAWASAKI BALIUS2, KAWASAKI BALIUS, KAWASAKI XANTHUS, KAWASAKI ZXR250R, KAWASAKI ZXR400R, KAWASAKI ZXR250, KAWASAKI ZXR400, KAWASAKI ZXR750, KAWASAKI ZZR400
Soak in Gasoline for a little while to stretch it a bit and get it just right.
As others have said, at first the Rubber is too short and not very attached.
If you force it on as it is, it will bite and overflow all over the place.
It is recommended to soak the packings in Gasoline for a little while before use so that the packings will stretch nicely.
p.s. If you soak it too long, it will grow too long and you will not be able to get into it, so if it grows too long, let it dry for a while.
View detail
It's good to use for cheap taste.
It's good to use for cheap taste. But the bike isn't strong enough, so if you fall, I think it's going to break. I think expensive products are good for people who can't use them. View detail
Fits: KAWASAKI Z400FX/Z400J, KAWASAKI Z500, KAWASAKI Z550
The molding is great, but the production accuracy is disappointing.
A 38 year old OEM footpeg rubber was cracked due to decay, so I was looking for a used one, but I couldn't find a good one, so I came across this product and bought it.
Z1000R/for Z400GP's Replacements are also from a certain manufacturer, but the shape is slightly different from the FX's, so I didn't adopt it.
As for the construction, the product I received was excellent.
I'll install it on the body of the car in anticipation.
Right Side, nice touch. Best angle and orientation!
Left Side, Mmm! The Sauce angle is fine, but the footpeg is pointing back a little bit when you look at it from above.
Would it be easier to understand if I said it looks like I hit the curb with my footpeg while driving and it bent?
I've tried re-installing it, moving the moving parts, and putting weight on it with my feet, but the angle remains the same.
It will be positioned a little farther away from the Change Pedal, so the controls?
The Manufacturer's description says that only CHERRY's footpegs are not attached to the OEM footpeg holders.
I ported only CHERRY's footpeg to the OEM Footpeg Holder.
And what do you think? Pi CHALY straight on! (You're on your own here.)
In the end, I came to the conclusion that CHERRY's footpeg herder (in our case, Left Side) is not subtly angled at the right angle. Since it is made by welding, it must be Large strange to get the angle out.
Finally, Right Side uses CHERRY's assembly products in its entirety, and Left Side is OEM Footpeg Holder+CHERRY's footpeg only and settled.
I drove about 200km after installing it, and I have not found anything strange at all, and I feel glad I bought it because of the Beauty around the footpeg.
I'll try to fix the LeftHolder that doesn't show the angle in my spare time! (^^)
Anyway, in the rejuvenation of the footpeg circumference that has been given up, I thank Mr. CHERRY who has put it on the market with splendid modeling for Large change.
How long the life expectancy of Rubber is a matter of concern, but I would like to use it in Large edition (^^)
View detail
You'll have to bevel them yourself
Installed on CRS33Φs. I wanted to try LongFunnel and JB POWER's 75mm Exchange from
As the description says, the hole chamfering is sweet and needs to be treated before installation, Sandpaper is used
There is a small scratch on the mounting part that does not affect the appearance and function
In addition, the chamfering of the corner part is also not good, so I chamfered this part as well Better
There is an explanation for the case of tight mounting, but this is rather loose and has an acceptable amount of rattling There is a moon
There are many parts that are not finished to Carburetor, which is a precision part, so I am concerned about that Recommends not to those who will be
My impressions of the street driving only, but since it was originally a long funnel, no changes to the settings It works fine and there is no change that you can feel
View detail
cheap
I replaced the Handlebar for a change of pace
It is easy while driving, but because it is a squeezing handlebar, the handling of the vehicle and the small turn can be done a little It's hard
I replaced it with another Handlebar after using it for about six months, but since the price is cheap, I had to use it for fun I think it's possible to change it
View detail
Fits: KAWASAKI ZEPHYR400, KAWASAKI ZEPHYRX, KAWASAKI ZEPHYR750
The quality is not great
There may be child Wound at the time of manufacture
There are a lot of fine wounds and uneven plating Four screws on the front are also different from the product photo, and because there is no washer, you can make it by yourself Installed (Spec. change?)
It's a bit disappointing because it looks and feels like a Large thing
Well, Parenthesis is good, that's for sure
View detail
It is subtly BALI
This is a great way to get a good grip on your clothes But there was one item that had a BALI in the molding process, and the BALI itself isn't severe I didn't have any trouble using it because of the, but it's not very pleasant View detail
If you're worried, though, you might want to stop
It's not an OEM product, but as long as it's built with grease on it, there's no air leaks or anything like that I've been able to use it for several years without it
This time I reeat it for another vehicle, and if you mess up when you remove the Spigot, you can repair it Scared every time because of the incompetent situation & Spigot doesn't want to repeat the removal too aggressively So, if you're unsure, it's better to go with OEM
View detail
We're doing a good job for our price
The RAMAIR Filter I was using originally became useless, so I replaced it with this one
The hole is so small that you need to widen it when you install it to cover the funnel You may need to make a small cut in the funnel
RAMAIR and Setting remained the same
The RAMAIR is more durable
The RAMAIR was useful for about 5 years, but this one fell apart after 2 years
Right now it's still Funnel
I think it's a good idea to have it as a precaution against vehicle inspection
View detail
A little more
I bought this one because it was the only one I could find for the light size and mounting width
If it is Made in Taiwan, I thought it would be Large but it is a good price
problem
I'm very scared by vibration (used with a single cylinder) → Rubber against the upper hook I put a PVC Tape on the bottom of the unit and the jumpy sound stopped I tried many things and this was the hardest to do
It has been wet in the rain for a few times because it is stored in Garage, but the plating part has rusted I recommend protecting it with Wax etc. immediately after you buy it
Compared to the NORMAL time, Cutline was severe and flare appeared on the Right After all, I am now using Small Yarn's 140? In comparison to Cutline, the spread of light is far different
It's not cheap considering the price
good point
This is the only size I could find
Cases are matte because all platings are too shiny [Color] I was able to make it look like aluminum with Clear
You just need to install it and everything will be fine
View detail
Fits: HONDA CB400FOUR (NC36), HONDA CB400SF, HONDA CB400SS, YAMAHA SR400, YAMAHA VMAX, YAMAHA XJR400, SUZUKI GS400, SUZUKI IMPULSE400, SUZUKI INAZUMA400, KAWASAKI 250SS MACHI S1 , KAWASAKI 350SS MACHII S2 , KAWASAKI 400SS MACHII S3 , KAWASAKI 500SS MACHIII H1 , KAWASAKI 750SS MACHIV H2 , KAWASAKI BALIUS, KAWASAKI KH250, KAWASAKI KH400, KAWASAKI KH500, KAWASAKI W400, KAWASAKI W650
Overhaul alternatives
I bought it with no expectations at all Or rather, I used it in time while I was taking the Nitron out to Overhaul I don't mind it so much when I ride around town, but it's still just Spring It was awful to compare it with the product I can buy for almost 20 pieces View detail
But for those who only think about Cut
Seal chain to non-seal (Clip equation) The purchase is only to change the
This Cutter can cut the Chain once, discard the original Chain, and
This is an item for those people
It's cheaper and better if you just want to cut it, but if you want to use it repeatedly
Buy another luxury item
The quality of the Chain Pin extruding rod is poor and the shaft is straight in a blur
Can't press Pin
Probably the bar is only at the lowest level of strength, and if the pin is hard, it will break easily
So, shave the head of the Pin until it is flat before using it
When you say it's worth the price, you can say it's a product that requires a lot of dedication and determination
By the way, the handle is just stuck on the standard screw, so it's not as long as the appropriate length
If you stick a bolt in it and use it as a handle, you can hang a lot of power on it
Most of all, though, Cutter's Stick can't stand up to its power
View detail