Reviews
Fits: YAMAHA MAJESTYS, YAMAHA SMAX (SG52J), YAMAHA SMAX (SG28J), YAMAHA SMAX (SG271)
It will be Stylish!
[How is it used?
It was adopted as we proceeded with the dress-up of various areas.
We have asked Motorcycle shop to install at BigPit inService.
Was the one you received as per Image?
It was just as Image.
How was your experience with it?
It looks very good and I am satisfied with it.
[Points to note]
It is a little bit difficult to install, as it requires an OEM Fender cut. If possible, it would be better to ask the Shop to do this for you.
How did it compare to other products?
I thought it looked more stylish and better than other Manufacture's products.
View detail
Fits: HONDA PCX125 JF28, HONDA PCX125 JF52, HONDA PCX125 JF56, HONDA PCX125 JF81, HONDA PCX125 JF84, HONDA PCX150 KF12, HONDA PCX150 KF18, HONDA PCX HYBRID 2AJ-JF84
Brake stopper
When parking a scooter in a tilted parking lot, be careful because of the lack of gears. Even beginners can easily install the Brake stopper and operate it with a single finger. This is the first product we recommend to prospective Scooter buyers. View detail
Fits: HONDA PCX160, HONDA PCX150, HONDA PCX125, HONDA PCX Hybrid, HONDA PCX e HEV
It is perfect.
Mounted on Pcx160.
The right hole for the switch box is a simple addition, while the left hole is re-drilled about 2cm outward from the OEM position. (5mm Drill) 。
The line WOUNDS somewhat, although I worked with care because the line is only lightly rubbed.
I installed High Solo at the same time and had no problems.
Very good product
View detail
18-year old BirdCity125 (SEC-1J) Fender Eliminator-ization of
I wanted to change the Fender Eliminator on my '18 BirdCity125 and move the RearCameraPosition on the DriveRecorder to the original Reflector position. I was also convinced that the size and design of the '17 BirdCity155 and the '18 BirdCity125 were the same, so I checked the specifications and looked at the rear view of both vehicles to make sure they were the same and purchased the kit.
The first thing that puzzled me when I received it was that it came with an LED License Plate Lamp.
I had ordered a KOSO Bracket with License Plate Light because I thought I had to prepare and install a License Plate Light separately when converting to Fender Eliminator! I had ordered a KOSO Bracket with License Plate Light, so I had to return that one!
When machining, the Fender is removed from the body and masked according to the Instruction Manual, then carefully cut using a blade for plastic or PPMaterial, and then file it with Paper No. 100 or higher to cleanly shape it.
For installation on the vehicle body, the License Plate is temporarily assembled, and holes are drilled after checking the position and levelness of the holes and marking.
The 7mm hole was specified, but I don't have one, so I used a 6mm drill and had no problem.
The holes drilled are also cleaned up with a stick File.
Wiring of License Plate Light is cut by Lamp side Limit of OEM License Lamp to use OEM Coupler and Wiring, and after wiring process, it is crimped to Female Bullet Type Terminal.
The wiring of the attached License Plate Light is also crimped to Male's Bullet Type Terminal, and since the wire is very thin, a solder is added to connect both.
The light came on safely when I installed it in the car body and turned on the main key to check the light.
Just to be clear, on the body side, Black is Minus and Blue is Plus.
On the License Plate Light side, Black is Minus and BlackWhite is Plus.
The wiring routing was done using the hole where the Reflector was originally attached, and the process was completed in the space on the reverse side of the Reflector.
After that, side cover, helmet in, etc. were all put back together, and this Bracket was finally combined with DAYTONA's with ReflectorLicense Plate Bracket and attached to the vehicle body to finish the work.
In summary, the License Plate Light is quite bright and the position of the light affects the RearCamera's image at night, making it appear bluish.
I have found that shading the tip of the camera lens with something that can be used as a flange will solve this problem, so I will take measures later.
I am very happy with the Refreshing Rear, which was heavy.
The drawback is that when the side cover is removed for maintenance or adjustment, the bracket is directly attached to the side cover, so it has to be removed, which increases the time and effort required.
As a supplement, it is not compatible with MODELs prior to 18.
Also, we do not know about BirdCity after Model change, so it is only BU54 (SEC1-J) Conformity with respect to (Diversion is possible.) Please understand that
View detail
US Buyers Read First
2016 Yamaha Zuma USDM. The part is very good. The fit and finish is fantastic and the install is pretty straight forward. BUT if youre in the US, this part will remove your OEM license plate light, so what you will need to do is cut the bottom oval of the black plastic tail light surround. The models outside the US have this precut, but we only have the outline. This will allow the tail light to serve as the license plate light. If you look at the description pictures on the listing, you'll notice the light hole. ALSO, the part is for plates somewhere outside the US therefore the license plate screw holes do not match up, you will need to re-drill two holes closer to the middle of the plates. I got the kit that ustilizes the OEM reflector, but shortly after install, I cut that bracket off for a reflector delete. View detail
Fits: HONDA PCX125 JF28, HONDA PCX125 JF52, HONDA PCX125 JF56, HONDA PCX125 JF81, HONDA PCX125 JF84, HONDA PCX150 KF12, HONDA PCX150 KF18, HONDA PCX HYBRID 2AJ-JF84
Brake stopper
I really appreciate this feature in normal driving in town and in situations where the vehicle body is required to be fixed on hills, so much so that I wonder why it is not included as Standard Equipment in the Scooter. View detail
I do not recommend it.
[How is it used?
I installed this on my commuter vehicle, a CYGNUS X 5 model. I was wondering if I would do the Fender Eliminator since I use it for commuting even on rainy days.
I got tired of the wild OEMFender that I saw every time I looked behind me and decided to install it.
Was the one you received as per Image?
The number of parts is smaller than I expected, and I thought it was such a Compact.
The material is probably steel, and the paint is weak and will soon peel off if bumped during installation, so be careful. Be careful when you bump it during installation.
Was the installation difficult?
It is not difficult, but it is a bit tedious because the entire rear cowl must be removed.
However, there are only a few Bolts that are stopped, so having the interior stripped makes the work much faster.
I use Emon's inner lining peelers.
The Instruction Manual is attached, but it is gubby and not clear. I think you will understand it if you look at the thing and the actual car and think about it.
I had to check the contents of the Instruction Manual for the center plate on the Net to install it because it made no sense to me.
How was your experience with it?
Honestly, it sucks except for the Styling from the back and the ability to install without cutting the OEM.
I would not recommend it to others, I feel.
First of all, the accuracy of the product is poor. I fine-tuned it many times until I was satisfied.
Plate bending accuracy may be poor, or there may be a gap between the boti or when tightening the number.
Bracket has floated away and the only way to tighten it up is to force it.
I had no choice but to hand Bent and install it myself to some extent.
[Included Parts:were they on?
The pictures are as shown. The basic bolts are OEM.
[Was there anything that disappointed you?
As described in the photo at the end of the image, the back of the Number is immediately Battery case.
Wiring is also fully visible. 10,000$ Fender Eliminator. I wish they would make it more seriously.
OEM Fender is $3,000 for a new one. It's not that expensive.
We recommend WirusWin's OEMCut type Fender Eliminator.
Wiring is also not really possible for the governor to be in full view, so I will make my own mudguards out of plastic dampproofing.
As I said at the end, I cannot recommend this Fender Eliminator.
View detail
It's cool.
I was wondering if you could do something about the Gold amount a little more. LOL! View detail
Fits: YAMAHA CYGNUS X (2-inch), YAMAHA CYGNUS X (3-inch), YAMAHA CYGNUS X (4-inch), YAMAHA CYGNUS X (5-inch), YAMAHA MAJESTYS (SE44J) (1YP), YAMAHA MAJESTYS (SE44J) (28S), YAMAHA MAJESTYS (SG28J), YAMAHA MAJESTYS (SEA5J), YAMAHA MAJESTYS (SED8J)
Isn't this nice?
Reasonable and affordable Image change is available.
The key cylinder is visible every time the engine is turned on, but I was concerned because the place where the key is inserted is a NORMAL color, like a …hmmm? The color of the key cylinder is like a skin color, and it is getting a little dirty, which was bothering me.
There are products that cover the entire surface, but I chose this one because it is cheaper and easier to apply. The color is Black, and I can't say for sure because I have my own preference for design, but I like it.
I am a little worried about the durability of the adhesive. I warmed it up a little with a fan heater and carefully degreased the key cylinder side before applying it.
View detail
How effective would it be?
I bought it with the static eliminating Bolt and some kind of product that is hard to tell if it is effective or not, because I got quite a bit of it when Point purchased the Full Exhaust System. To tell the truth, I was reluctant to purchase the product at actual cost.
Used for empty Bolt hole in FinalDrive gearCase of R1250RT.
Since Oil is also used inside the Gearcase, we tried attaching it to the Gearcase for its static eliminating effect, but the extent of the effect is unknown.
View detail
Fits: YAMAHA MAJESTYS (SG28J), YAMAHA MAJESTYS (SG52J), YAMAHA MAJESTYS 4- (SG52J), YAMAHA MAJESTYS 4- (SG28J)
High quality Backrest & Pillion Bar
[How is it used?
Tandem Time
Was the one you received as per Image?
As shown in the image, the red stitches match those of the Seat, which appears to be an OEM product.
Was the installation difficult?
Easy
How was your experience with it?
good
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
View detail
It's just too expensive.
It's just a Fender Eliminator, but it's too hard to put on. View detail
Useful on gentle slopes.
It is easy to let go of the brake when stopping uphill.
However, when the gradient becomes steeper, the weight of the car overpowers it and it moves backward.
View detail
the expendables
I change them regularly because they are consumable. View detail
The BB-SHOOT is a special sponge filter for BB-SHOOT.
Naturally, it can only be used with BB-SHOOT Air Cleaner. At first glance, it looks like free Sponge, so 1pc.1100 for one replacement (less than 1 to 2 months). I think that the price is too expensive, so I use a new Sponge and replace it at the time of 800 kg oil change, and wash the once-used Sponge with neutral detergent and dry it for a total of 2 times. The sponge used once is washed with neutral detergent and dried for a total of two times. I guess it would be better if I wash it more frequently because it gets dirty, but if I use more than 1000 kg of Sponge, I cannot remove the dirt and it remains on the Sponge. View detail
Fits: YAMAHA CYGNUS X (4-inch) EBJ-SEA5J, YAMAHA CYGNUS X FI (SE461), YAMAHA CYGNUS X FI (SE462), YAMAHA CYGNUS X (4-inch) SED8J, YAMAHA CYGNUS X (Model 4) SEA5J, YAMAHA CYGNUS X (4-inch) 2BJ-SED8J
Nice price, but the shape is good.
OEMFender to be removed and installed Type
Refreshing the best on the market.
All the back must be removed from the Seat to install it.
Large oddity.
By the way, there is no manual enclosed on how to remove it, so if you can't do it, pay the labor charge and have a PRO do it for you.
Reverse side is bare Wiring, but there is a Fender on the Tire, so it may be Large sturdy.
View detail
Fits: YAMAHA SMAX, YAMAHA SMAX, YAMAHA SMAX, YAMAHA MAJESTYS
You don't have to have it, but it's definitely better to have it.
Mounted on MAJESTYS.
It is easy to install, I think STD Shape levers can be installed even with external levers. I use it with KOSO's Lever.
Parking brake cannot be operated with one hand.
Lock with the Right hand while gripping Lever.
It would be more convenient if it could be locked with one hand.
View detail
Question on quality
The thing is nice and cool, but the License Plate Light ran out halfway through the month. View detail
Fits: HONDA PCX125 JF28, HONDA PCX125 JF52, HONDA PCX125 JF56, HONDA PCX125 JF81, HONDA PCX125 JF84, HONDA PCX150 KF12, HONDA PCX150 KF18, HONDA PCX HYBRID 2AJ-JF84
pcx150 (KF18) Mounting on
I thought it was a little expensive, but I installed it because I couldn't keep my hands off the car when I stopped. The work is easy. 10Driver and Pliers (Lower Nut co-rotation stop) Use the screw. The screw of the shaft is removed, this product is installed, the screw of another purchase is installed, Nut is tightened, and it is completion. When both hands are released at the time of a stop with this, Parking lock is done. View detail
Repurchased for processing
I bought this again for my RAMAIR filter lid.
It's just right, both in thickness.
View detail