Reviews
Fits: YAMAHA MAJESTYS, YAMAHA SMAX (SG52J), YAMAHA SMAX (SG28J), YAMAHA SMAX (SG271)
It will be Stylish!
[How is it used?
It was adopted as we proceeded with the dress-up of various areas.
We have asked Motorcycle shop to install at BigPit inService.
Was the one you received as per Image?
It was just as Image.
How was your experience with it?
It looks very good and I am satisfied with it.
[Points to note]
It is a little bit difficult to install, as it requires an OEM Fender cut. If possible, it would be better to ask the Shop to do this for you.
How did it compare to other products?
I thought it looked more stylish and better than other Manufacture's products.
View detail
18-year old BirdCity125 (SEC-1J) Fender Eliminator-ization of
I wanted to change the Fender Eliminator on my '18 BirdCity125 and move the RearCameraPosition on the DriveRecorder to the original Reflector position. I was also convinced that the size and design of the '17 BirdCity155 and the '18 BirdCity125 were the same, so I checked the specifications and looked at the rear view of both vehicles to make sure they were the same and purchased the kit.
The first thing that puzzled me when I received it was that it came with an LED License Plate Lamp.
I had ordered a KOSO Bracket with License Plate Light because I thought I had to prepare and install a License Plate Light separately when converting to Fender Eliminator! I had ordered a KOSO Bracket with License Plate Light, so I had to return that one!
When machining, the Fender is removed from the body and masked according to the Instruction Manual, then carefully cut using a blade for plastic or PPMaterial, and then file it with Paper No. 100 or higher to cleanly shape it.
For installation on the vehicle body, the License Plate is temporarily assembled, and holes are drilled after checking the position and levelness of the holes and marking.
The 7mm hole was specified, but I don't have one, so I used a 6mm drill and had no problem.
The holes drilled are also cleaned up with a stick File.
Wiring of License Plate Light is cut by Lamp side Limit of OEM License Lamp to use OEM Coupler and Wiring, and after wiring process, it is crimped to Female Bullet Type Terminal.
The wiring of the attached License Plate Light is also crimped to Male's Bullet Type Terminal, and since the wire is very thin, a solder is added to connect both.
The light came on safely when I installed it in the car body and turned on the main key to check the light.
Just to be clear, on the body side, Black is Minus and Blue is Plus.
On the License Plate Light side, Black is Minus and BlackWhite is Plus.
The wiring routing was done using the hole where the Reflector was originally attached, and the process was completed in the space on the reverse side of the Reflector.
After that, side cover, helmet in, etc. were all put back together, and this Bracket was finally combined with DAYTONA's with ReflectorLicense Plate Bracket and attached to the vehicle body to finish the work.
In summary, the License Plate Light is quite bright and the position of the light affects the RearCamera's image at night, making it appear bluish.
I have found that shading the tip of the camera lens with something that can be used as a flange will solve this problem, so I will take measures later.
I am very happy with the Refreshing Rear, which was heavy.
The drawback is that when the side cover is removed for maintenance or adjustment, the bracket is directly attached to the side cover, so it has to be removed, which increases the time and effort required.
As a supplement, it is not compatible with MODELs prior to 18.
Also, we do not know about BirdCity after Model change, so it is only BU54 (SEC1-J) Conformity with respect to (Diversion is possible.) Please understand that
View detail
It's cool.
I was wondering if you could do something about the Gold amount a little more. LOL! View detail
Very Refreshing.
My Motorcycle is not the year listed but it fits well. 2021 CB125R (JC91)
The heavy Normal fender has been refreshingly changed to a light 125cc look.
Large custom parts that can be transformed beautifully without destroying the atmosphere of NORMAL.
Blinker's Wiring is just attached as it is, but License Plate Light was a little troublesome because I had to process it by myself.
There is a Dent (Wound) that may have been attached when bending the Plate of the genus Gold at the time of production, but considering the total, I am glad I bought it.
Also, it gets pretty deep, so I wouldn't recommend it if you're driving in the rain.
View detail
I bought this to make my GSX-R125 more parenthesis friendly.
I bought this because I didn't like the OEM very large Fender and wanted a Fender Eliminator.
I chose this Manufacturer's product because it was the shape that I liked the most after comparing the installation pictures with those of other companies.
Needless to say, the Fender will be gone, so water will be rolled up and the back and Rear Sets will be dirty.
View detail
It's justice to look good.
I bought this as a Fender Eliminator to go with the stylish design of my newly purchased Special Knife Address110 for commuting. If you have a regular sander, air saw, electric Drilletc. or a regular maintenance person, you will have fun and complete the work in less than an hour. screw lock and SpringWasher are good to have ready. View detail
The NumberLight is dangerous
The ease of installation of the Number can be done by anyone with a tool, but the NumberLight's Wiring process is a little complicated?
In particular, NumberLight does not paste well and peels off
Other than that, the Fender is gone and the angle is Mischief It was cool
View detail
Tighten up around the rear
I think the long rear Fender is the reason why it looks like an old man's motorcycle Replacement The result is quite young
Installation is simple; the claws on the Cowl need to be worked carefully so as not to break Especially the cowl under the tail lamp should be pulled straight back
Replacing License Plate Light is also surprisingly easy
When it rains, it picks up a lot of muddy water, which makes the carrier and the tail lens a mess There will be none
View detail
Refreshing a stretched out Rear Fender, looking young!
I bought the Fender Eliminator to make the rear view look more youthful
As expected of ADIO, the production is solid And it is safe because License Plate Light can be ported
There are two types of Reflector:one for OEM use and one for this purchase with Slim Reflector I have a thing, but it was about $1,000 more expensive because I wanted to give it a Refreshing feel! has made this product
The installation took about an hour
The instructions say to remove the tail lamp and cowl, but the Helmet in and Fender BoltQuantity:Remove the 2pc and you can get the Fender (requires a bit of a hang It's only at your own risk! (Laughs)
If you have come to this point, you can install this product and handle the wiring of the License Plate Light (Secure with Tie Wrap) and you're done
The position of the number can be fine-tuned so that it is in the center of the vehicle
My impression of the installation is that Parenthesis is better than I expected!
If you have a CALI Sticker plate, it may interfere with the vehicle depending on the direction of the plate I have changed the direction of the plate (I have to go get a sticker!) and it won't stick straight I changed the direction of the Plate to deal with it (I have to go get a sticker!)
Recommended for people who want to make their rear end refreshed and give a custom look !
View detail
It is quite good.
I can't cut off the Fender, so the Fender Eliminator Kit is very Recommendation ⌒⌒⌒
The communication from shipping to arrival was very thorough and very reassuring!
View detail
Making is good for the price.
Purchase to get Fender for GSXR 125.
I was worried because it was cheaper than those of other companies, but the making was firm without BALI, and Screw Pitch etc was easy to install because of insanity.
However, since there was no Space like Reflector 's Bracket which can put two kinds of Seals, Performance only ★ 4.
View detail
Fits: HONDA GROM (JC61) *Not available for MSX of ThailandSpec.
ADIO's short tail license plate stand is on time~
The MSX125 with this short-tail rack is so handsome. The original one is too ugly. I looked at it on Taobao and found that the quality is not ideal. Later, I found this car on the webike. Corresponding to the modified parts, I decisively started with this short-tailed card rack and some other small things. The logistics is still possible. It only took 5 days from order to hand~ MSX125 with this short-tailed card rack is really handsome, the original factory is too ugly, looked at Taobao, are the quality of the cottage factory is not ideal, and later found my car on webike Corresponding to the modified parts, decisively start this short-tail card holder and other small things, logistics can still be used from the order to the hand only took 5 days ~(translated by Google Translator) View detail
Quite good
Even though the installation Bracket, originally one for each for Rightfor Left, must be included, but when I purchased it ... which one was for sure which two for LeftBracket was in and for RightBracket It was in a state not in existence. For that reason, I contacted Webike and got RightBracket sent ... ... etc .. Although there was a sorrowful one, there was reconfirmation that it is a good thing in the middle if installed.
It looks better and it is wonderful to say "It seems to be sturdier" than anything above OEM above anything, so if this is a little or gentle vibration it is Hetchara Hui. License light is also bright with LED, White .......
For those who are sturdy and still looking, I would recommend this. If you correspond to the model
View detail
cool
Compared with some Fender Eliminator, I feel texture, Style seems to be good so purchase.
Large strange as I have to remove a lot of OEM removal, but those who can clear them without problem
I think that it is affordable for installation.
Fender cut and drilling are unnecessary. OEM Wiring to install License Plate Light
It is necessary to install it by Cut, but included in Kit LED Wicing of License Plate Lamp is very thin
Therefore, rather than using the included Bullet Terminal terminal, it is recommended to connect with a connection terminal for fine wires such as Emon.
A person who wants to use Blinker other than OEM structurally considerably devises or does not recommend it because it can not be attached unless the installation position itself of the Blinker is changed to the car body.
Blinker is firmly attached to good people at OEM, Refreshing around Rear and texture is perfect.
View detail
Fits: SUZUKI ADDRESSV125 S, SUZUKI ADDRESSV125 SLIMITED
Pay attention to your car! Parenthesis inject goodness (Lol)
The lowest price among Fender Eliminator products?
I think that the atmosphere changes subjectively though it is subjectivity.
[About the product]
- License Plate dedicated to car models Bracket and Bolt & Nut
Enclosed and the quality of Bracket is also good.
- At first glance it seems to be able to make it myself, but collect materials for similar quality
Thinking about processing, it is definitely better to buy Kit.
- Design is also unpleasant with Simple. I do not feel anything.
【About installation】
- Depending on the car model, Address disconnects NORMAL's Rear Fender
I will drop it.. Surprisingly Material is soft and easy to cut.
- I am an ordinary machine tool Cutter (Large in the middle?) With a cut
It put it in several times and finally cut off the blade deeply.
Even if you can not put a blade deeply at once, like up and down like Quantity : Pair (for Left and Right) To
Instead of stinking, moving the blade in one direction to repeat
The person who does it may cut cleanly.
- We need perseverance so as not to scratch the surroundings.
(Dustclothetc. It would be nice to protect the surroundings)
【About Fitting】
- It is exclusly for car models only and can be installed.
Drill holes in the remaining SIDE's Fender to fix Bracket
It is inconspicuous and simple.
If you follow the instructions, OEM's Reflector will be hidden by half, but it will be anxious
It is not. Here we decide the range to cut beforehand as you like
It's a good idea to keep it..
- Check the angle of Number by adjusting the Bracket up and down according to your preference
Let's tighten and fix Nut and Bolt from.
[After installation / Merit]
- Rear Refreshing in Race ish, finished with a good feeling.
- Considering the angle of Number, casual Large person Spec. !?
- Of course, I feel self-satisfied..
- The car wash around Rear has become easier.
[After installation / Demerit
After all it will be mud when the rainy weather etc..
I attach VECSTAROEM 's Rear Fender,
It can not be changed to AddressOEM.
【Impression】
My car is PetitCustom and I feel better!
Moreover, although I run like my everyday in commuting, there are no defects in the product.
It is only this, but a feeling of special may come out on my car (Lol)
View detail
Fits: HONDA GROM (JC61) *Not available for MSX of ThailandSpec.
Very good tail tidy for the price and much better than the tyga one IMO, I would highly recommend this for the price and quick delivery
Very good tail tidy for the price and much better than the tyga one IMO, I would highly recommend this for the price and quick delivery View detail
Fits: HONDA GROM (JC61) *Not available for MSX of ThailandSpec.
This product is very well made, very easy installation and fits like a jem. Licence plate light and indicators fit nicely as well, no alteration is needed at all.
This product is very well made, very easy installation and fits like a jem. Licence plate light and indicators fit nicely as well, no alteration is needed at all. View detail
Fits: YAMAHA CYGNUS X 13- SE44J (Japanese specification1YP), YAMAHA CYGNUS X SR 13- SE44J (Japanese specification1YP), YAMAHA XC125 XC125 SE465J (Taiwan Spec.), YAMAHA XC125 XC125SR SE465J (Taiwan Spec.)
The ADIO Fender less kit was attached.Structure of details has improved and modeling is also beautiful.There is neither attachment nor the necessity for processing with a pure exchange Type.A Cost is also very satisfactory at a low price.
The ADIO Fender less kit was attached.Structure of details has improved and modeling is also beautiful.There is neither attachment nor the necessity for processing with a pure exchange Type.A Cost is also very satisfactory at a low price. View detail
Fits: YAMAHA CYGNUS X 13- SE44J (Japanese specification1YP), YAMAHA CYGNUS X SR 13- SE44J (Japanese specification1YP), YAMAHA XC125 XC125 SE465J (Taiwan Spec.), YAMAHA XC125 XC125SR SE465J (Taiwan Spec.)
The Fender less kit of ADIO does not have the necessity for processing by a pure exchange Type.Also in modeling, the circumference of rear one improves shapely, and its Cost is also satisfactory at a low price.
The Fender less kit of ADIO does not have the necessity for processing by a pure exchange Type.Also in modeling, the circumference of rear one improves shapely, and its Cost is also satisfactory at a low price. View detail