Reviews
To OEMCarburetor
Installation is easy, just remove the Carburetor and replace it!
It's a bit of a hassle to get the Tie Wrap to hold it in place.
I've Refreshingly lost the Choke Lever on LeftSwitch.
View detail
Fits: KAWASAKI ELIMINATOR 250LX, KAWASAKI ELIMINATOR 250LX
Not for the ELIMINATOR 250 or 250SE:!!!!
The Choke Cable for the ELIMINATOR 250 was out and I looked up the OEM to replace it, but it was already discontinued.
I was looking for a third party product and found this one from HURRICANE. The only model that fit was the 250 LX, but I didn't think there was any particular distinction between the LX, unmarked and SE.
However, the structure of LX is different from that of Muji and SE. Installation is not possible without considerable modification.
The texture is very good, so you can't complain about it if you properly research the model of car that fits.
View detail
Used for bar handling of CUB
Because CUB has a Chalk lever on the Left Switch Box,
As there was no way to go to Bar handle, I moved to Side cover. At this position it interferes with the Frame so we need to devise an angle, but it is satisfactory at a position that is very easy to operate.
View detail
[Webike Monitor] It purchased in Bar-handle-izing of ZZR250. I think that they are the necessaries at the time of the Bar handle. Since there are a 100-mm Long and a 175-mm Long, cautions are required. As compared with pure Handle height, I
[Webike Monitor] It purchased in Bar-handle-izing of
ZZR250.
I think that they are the necessaries at the time of the
Bar handle.
Since there are a 100-mm Long and a 175-mm Long, cautions are required.
As compared with pure Handle height, I purchased a 175-mm Long.
Although exceeded by change of management so far [
], room was produced by Cables by the right management by the favor of this product.
Although
engine performance does not change in particular that it is pure, I think that I will also perform a Maintenance of the Cables neglected so far, taking advantage of this opportunity.
View detail
Fits: KAWASAKI ZRX1100II, KAWASAKI ZRX1100, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S
A 5-cm long type is used for ZRX1200. Since 1.2-cm UP of the handle was carried out by 2-cm UP and a clamp part, since it stopped arriving, axel wires were exchanged with the pure accelerator cable, but chalk cables were also united and exchanged.
A 5-cm long type is used for ZRX1200.
Since 1.2-cm UP of the handle was carried out by 2-cm UP and a clamp part, since it stopped arriving, axel wires were exchanged with the pure accelerator cable, but chalk cables were also united and exchanged.
However, after exchanging, he noticed, but since it is that the quality of a motion uses a chalk cable unlike the throttle wire linking directly to a motion of a motorcycle only at the start-up time and a handle is a center valve position in general in many cases, the roughness of a motion of a few is not related.
Of course, when 5-cm or more UP was carried out, the die length of the wire itself becomes less insufficient, and the motion of a handle was also influenced only in management, but in 3cmUP like me, it was not so influential.
About goods, fitting relations are the pure form itself, and that this is replaced with metal differ to the play adjusting part of a wire being a plastic an authentic positive ones.
Although a wire is also considered for an authentic positive one to be iron probably, it is a product made from a stainless, the teflon tube exists between a wire and a cable outer, and it is fully considered here also about the motion, and it serves as a thing also with structure and a sufficient pure twist.
(Of course, a pure twist is also a little expensive) We recommend you to exchange, before going out by preventive measures, if it is the environment where the motorcycle is old or is damp to rain in many cases.
View detail