Reviews
Fits: KAWASAKI Ninja H2 SX, KAWASAKI Ninja H2 SX SE
Speedra Carbon Tail Light Cover
The OEM ABSTail Lamp Cover is cheap, so we changed it to …Speedra's Carbon Tail Light Cover!
The texture will be much better.
View detail
Well, I guess I'm satisfied.
I think the accuracy is somewhat good, but the Edge is a little hard to hit.
There are some gaps.
View detail
Seat Cowl connected and Refreshing.
The Seat Cowl is also made of the company's Carbon, which gives a sense of unity.
I was hesitant to buy it because the price was so high, but when I put it on, I was glad that I bought it.
The Rear area is now fully Carbon Spec.
View detail
If only it were a little cheaper lol.
I was hesitant because of the high price, but when I installed it and looked at it, I am glad I purchased it. I had to adjust the screw position to see if it was an individual difference. View detail
Slight modifications were needed.
The twill weave and glossy finish gave it a Gorgeous atmosphere at once.
I will upload a picture of the installation, but there were some areas that were sized over OEM, so I had to do a lot of shaving in the file.
The part protruding from the masking tape is the Oversize part. I cut here and there other than in the picture, but the bolt holes were correct.
If you do not use the OEM product, you can see the overlay.
As is usual with dry carbon products, it would save time and effort when installing the product if it were shipped with a little more fine-tuning after completion of the product. However, even if this is not the case, Parenthesis has a quality that OEM products do not have.
View detail
Only looks
Installed on a GSX-R1000R 2019
Color with inferior texture:This is a custom part to replace the tank side cover, which is an unpainted resin part, with dry carbon.
The texture is impeccable, as you would expect from Dry carbon.
Since these parts are relatively large in area, they contribute significantly to the quality of the overall appearance of the car body.
This part has Sponge/Rubber and Surface Fastener attached to it, but SUZUKIOEM Parts are included in the law.
If they went to the trouble of preparing it, I think it would have been better if it had been attached from the beginning, but I feel that just having it securely attached is sufficient consideration.
The bosses, etc., are also in the correct position, and are made by FOR JAPAN MODELMANUFACTURER.
The overall alignment is also fine.
However, the only claw that hooks onto the tank cover at the front of the vehicle body is not present, so this part of the body is slightly wobbly.
(However, since it is Kachica Dry carbon, not OEM's soft and sticky resin, it basically didn't bother me unless I dared to pull it by hand.)
Also, perhaps because it is different along the OEM (?) If this is a problem, you can fill the gap by applying a suitable thickness of sponge to the lumpy part of the tank on the reverse side.
After all, it is a replacement for Cowl, a design component, so functionally it is no different from Large.
Since the original OEM product is resin, there is no weight saving effect, and considering the cost along the road, I think the OEM product is better in terms of functionality.
but the texture improves well for the price.
Also, because it is a SPEEDRA, the weight carbon is a heavy-spec material, unlike the Large and a half weight carbon of other companies' products.:Carbon.
Moreover, this is sold at a discount to other companies. (I don't know how it is at this point, as the price went up a while ago.)
I think this is a very attractive option for those who want to improve their appearance.
View detail
W more than I expected.
Purchased to increase appearance Impact
There were no distortions and it was more complete than I expected for the price.
Bolted holes on the back are Material:Plastic. But I don't mind because it is an invisible part.
As others have written, threaded hole machining is required.
View detail
I can recommend it.
Material:I was able to install it properly without any distortion, which is common with carbon products.
The price is lower than OEM, and I can recommend it.
View detail
difficult to install
Because it is carbon, it is lighter than synthetic resin.
It will also look better.
It may be because it is a Handmade product, but it looks a little messy.
I had to install it with a lot of force, and I was afraid that the claws might break.
I'm concerned about the gaps, which the OEM Panel didn't do.
If you're wondering, do you need a processing technique?
View detail
Seat side cowl
Material:Carbon Style is so beautiful, and Clear is painted so nicely, I can't say enough about it.
It's still a little distorted, so the edges are a little thin.
but
I love it because it looks beautiful and the carbon is parenthesis good.
View detail
A little bit of shape …
It took a bit of brute force to install, as I expected, but I guess that's about all you can ask for.
For Carbon lovers, this is a Recommendation.
View detail
Fits: KAWASAKI Ninja H2 SX, KAWASAKI Ninja H2 SX SE, KAWASAKI Ninja H2 SX, KAWASAKI Ninja H2 SX SE
Nice try…
I think this is unavoidable, but the shape is not Exactly, and it is a little bit forced.
But I don't think it's as bad as you think.
It was a little less than OEM and there were some gaps, but I don't think it will bother you because it is hard to see.
View detail
Fitting is ……
Buy with Tail cover
This one looks good too, but one of the two is not fitting well, and when you fasten it with Screw, it comes out when Pin?
I thought it would be nice to know that it wouldn't fall off while driving.
View detail
Fitting is ……
Because OEMTail cover was damaged, I changed it.
I ordered the twill weave with luster, and it looks good, but the fitting is not so good, because the position of the hole is gap, and the cowl nail is hard to get in.
It was my first time with Carbon parts, but I thought it would be like this after seeing various Net
It's a little expensive, but I thought it would be nice because it looks cooler.
View detail
It's a little different shape.
There is no particular modification and it is easily put on. I think there is individual difference, but in my case, the space between Tank and Cover is too narrow, so when I kneel grip, it interferes with Tank, so I put Vinyl Tape inside. View detail
Easy to install
OEM has a Cushion on the reverse side of photo 3. I reused it because it is only pasted with double-sided tape. View detail
Fits: KAWASAKI Ninja H2 SX, KAWASAKI Ninja H2 SX
I'm happy with the product.
I'm happy with the product and the Shop.
However, in terms of Cost, is it expensive? That's all I can say.
I know it's a Carbon part and expensive, but it's an expensive product.
View detail
good good
The wait was worth it. I saw the air bubbles... But it's okay. But again, it takes too long. But I'm satisfied. I'll order again next time ^^ View detail
good good
It's very good. The price is very good. I'll use it often. And also recommended I'll do it. Please take care of me. It was a pleasant shopping trip. ~ ^^ View detail