Reviews
Fits: SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000
I don't know if I'd do a Repeat.
Buy Luster Ari twill weave
The overall texture is fine. However, the corners of the [Color] Clear bald? Chips? And also, the whole thing is twisted (is it inevitable for carbon products?). Therefore, when viewed from the rear of the vehicle, the rear end of the chain cover is hanging toward the center of the vehicle.
The supplied Bolt is used to join the product and the OEM Chain CoverBracket (steel, cobent shape), but the screw length is not long enough and the screw does not reach the UNut's looseness stop (the supplied BT is TrussM3×8L, but 10L is necessary).
In addition, one OEM clip was reused to attach to the Swing Arm, but the mounting hole of this product was processed with a thick wall as well as the BT, so the clip length was insufficient and could not be reused (in the end, double-sided tape was used to attach to the Swing Arm, and the Chain Cover (In the end, it was attached to the Swing Arm using double-sided tape, and the Chain Cover itself was attached to the Swing Arm using reused OEMBT in two other places, so it was judged to be large and sturdy).
Also, not related to quality, but when installing this product, the OEM Chain Cover and OEM Chain Cover Bracket must be removed (the OEM Chain Cover Bracket is reusable), and the Rivet is fixed in two places. I think it's much easier than using a drill to remove the Rivet.
Material for several units of Magical racingetc. so far.:I was more disappointed than the above points because I had been using Carbon products and purchased this product with that feeling. If it had been 10,000 cheaper, I would have been satisfied, but if the price is almost 30,000 and the quality is this high, I will refrain from buying it next time.
View detail
I had high expectations because of the high rating.
I was attracted by the installation method and the design, and I had high expectations for this product because it was highly rated, but I was disappointed because the accuracy was so poor.
I asked the Motorcycle shop to do something about it, and they did their best, but there was nothing they could do.
It's a good price, so it's a bit of a gap, but it's better than nothing, so I'm putting it on.
View detail
Fits: KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
Overall messy.
[Color] There are a few Sauce in Clear, and there is quite a bit of polish left because the polishing is only stroking.
The corners and other parts when removed from the mold are also sweetly processed.
Since it is long, I expected it to be effective in keeping the mud off, but there was none.
I like the design, it's Dry so there is no transparency and it's a good value for those who can alter it.
I think this is a product that varies from individual to individual.
View detail
Not bad.
The design and anodized colors are good, and it stands out unexpectedly, so it is not bad for one point around the front.
It's not bad, but the workmanship is more subtle than I expected.
View detail
There was a Wound.
There is no distortion, and I think it is a product with excellent cost performance, but unfortunately, there was a wound of about 3cm on the Left Side Cowl.
I thought about returning it, but I didn't want to wait for months, so I just installed it.
Also, the screw hole was too small, so it needed to be widened.
View detail
Not functionalParts.
I bought this as a measure against dirt to the part of the hole where this Parts is installed.
As a result, it was not a dirt solution.
Running in the rain, water and dirt from somewhere (Sand etc.) comes in.
Manufacturer doesn't sell it as waterproof or stain resistant either.
This was a complete misunderstanding on my part.
So it's not a functional Parts, but a custom looking product.
It is good to be Accent as Custom in appearance.
The finish etc. is very good and I can recommend it for that.
Installation is easy
However, because there is RightLeft as others are also written, it is temporary there.
It needs to be confirmed at times.
The installation instruction manual says to use a screw lock agent to prevent the screw from loosening.
It's written, but as mentioned above, water and dirt can get in to clean it.
I think that it is better not to use too strong Screw lock agent for
View detail
underfunded
I have no complaints about the surface finish, etc. However, as I posted in the photo, the gap is not good? It needs some processing. If there is no gap? I'll buy another one from a different manufacturer when I can afford it. View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI GSX-S1000F
Difficulty with accuracy?
Edge needs to be handled.
If you leave it as it is, it will lift up and not stick nicely.
The original is thin, so be careful not to cut too much.
View detail
Fits: KAWASAKI Ninja H2 SX, KAWASAKI Ninja H2 SX
Well, that's about it.
Fitting is not a good idea.
The Left Side in particular is not quite as good.
There were a few places that interfered and it was difficult to make fine adjustments.
View detail
Accuracy is not good
I bought a twill weave mattress VERSION. The accuracy of the product is not good. Bolt will somehow fit in the Bolt hole, but as you tighten it will crack. Processing at the edge is sweet, I feel cheesy against the price. I do not know how other companies are, but I feel betrayed that Japan FOR JAPAN MODEL expects high quality of production. View detail