Reviews
Fits: SUZUKI Gixxer 150., SUZUKI Gixxer SF250, SUZUKI Gixxer 250
Gixxer 150 Replacement Procedure
The Brake Side is held in place only by a hex bolt, so it can be easily removed with an on-board Spanner and tools.
Daiso's Ratchet driver set (550 yen) is small in size, so it is more suitable for hard-to-reach places like this than a big ratchet set. It is good to have one!
I couldn't find any Grease, so I substituted Vaseline for now.
The Clutch Side is somewhat labor intensive, so if you think this is difficult, you should honestly have it attached at a store!
Clutch Side, loosen the Adjuster under the Tank, under the Hexagon Bolt, Yellow color→. Then loosen the top. When loosening the top, turn the longer hexagonal Red→ clockwise. Then the Wire will be loose.
Remove the Bolt on the Clutch Side, pull out the Lever, and remove the Wire Thailand.
For the Clutch Side, the Silver-colored Sleeve that was attached to the OriginalLever should be transplanted and then attached. At this time, please apply Grease to the Sleeve and Thailand Co.
If you put it back normally, there is no problem, but if you force it, you will bend the ClutchSensor, which is the resin sticking out from the Clutch holder side. It is a soft resin, so it will not break.
Fasten with a hex Bolt and retighten the Adjuster on the ? Then, tighten the adjuster and you are done. I could upload only 6 photos, so I omitted the finished drawing.
View detail
Fits: SUZUKI Gixxer 150., SUZUKI Gixxer SF250, SUZUKI Gixxer 250
All good.
The Gixxer 150 Lever has a poor reputation and is not a good fee ring, even if it is patronizing!
The Clutch Side, in particular, does not have an adjuster to reduce the number of parts, so it is difficult to make small adjustments.
Rather, from the grip, the pull, and the wobble, there is too much difference between the Original and the U-kanaya!
If you plan to drive it for more than a year, you'd better change it quickly.
Anyway, Parenthesis is great, Clutch operation is easier, and I can't say enough good things about it.
In addition, it is said that U-Kanaya's Engine Displacement Volume can be used on different motorcycles by replacing the attachment at the base if it is similar to the Engine Displacement Volume.
I ordered the Short Type on 08/31/2022 and it arrived on 9/4/2022.
Since there are up to six Up photos, I asked the customer to Google the installation itself, but I have included a photo that shows the shape of the unit.
I used Vaseline instead of Grease for Screw holes and drums, but I couldn't find it, so I will apply it properly when I can find it.
View detail
Fits: SUZUKI GSX1300R HAYABUSA GSX1300R HAYABUSA
With OEM, adjustments are a modest hassle.
The quality is good. Installation on GSX1300R HAYABUSA is easy as only one screw needs to be removed. View detail
Imprementation re-posted. It can be installed with no problems.
I was unable to install the Clutch Side and had to go a long way.
When I installed it myself, I couldn't get the clutch switch to fit, so I left it removed.
I bought a CanEngine Starter Motor from Mercury and installed it, but thanks to the kind advice of a person who installed the same one on the same motorcycle in the comments, I asked PRO to reinstall it and was able to do so successfully.
It was a good learning experience.
Lever is very Parenthesis.
It's easy to use.
The color was matched with Speedra's Bar End, but the Gloss is slightly different.
View detail
Fits: HONDA CB650F, HONDA CBR650F, HONDA CBR650R, HONDA CB650R
Good quality, easy to install
I'm sure everyone who likes Custom knows this, so it's a bit of a new thought for me.
The texture of the product is very good as expected.
Installation can be completed in 15 to 30 minutes for those who are somewhat familiar with handling tools.
Thanks to the Adjuster, the distance from the Grip can be adjusted.
Most people can make the position work for them.
It is available in a wide variety of colors, so it can be matched with various motorcycles.
View detail
Fits: YAMAHA XJR400R, YAMAHA XJR400
Comfortable to use
[How is it used?
The Brake and Clutch lever of the XJR400R has been this product since purchase.
Was the one you received as per Image?
It was originally attached, so it is hard to say, but I think it is as shown in the photo.
It would be nice to have many colors to choose from.
Was the installation difficult?
I think it is easy, even beginners can do it by watching youtube etc. where many people explain it.
How was your experience with it?
It is quite comfortable to use, and the short type is suitable for old cars and easy to grip.
[Included Parts:were they on?
None in particular
[Was there anything that disappointed you?
The anodized part seems to have faded considerably with age, which was a personal disappointment point for me.
View detail
The clutch switch is removed and installed.
I am satisfied with the texture, color and grip.
The Brake Side was easy, but the Clutch Side could not be installed with the OEM clutch switch in place.
I just can't get it to stick with my worksukill.
I thought I had to apply for a conformity warranty because I bought it thinking it would come with it, but I wanted to use it, so I didn't.
I removed the Clutch switch and the Lever was attached, but the Cell only rotates in N.
If the engine stalls in first gear, you cannot hold the clutch and start the engine, so you must put the clutch in N and restart the engine.
Clutch switch for Kawasaki 3-pole, Connector for Cancellation *Spec.
I would like to try this product because I found a product that is inexpensive and could be used to protect the Connector.
Maybe I should have made the Lever a Speedra too, to match the color of the Bar End of the Speedra exactly?
View detail
Fits: HONDA CB125R, HONDA CB250R, HONDA CB150R, HONDA CB300R
Short Type.
Clutch and Brake lever of CB250ROEM are
Why is it so far away?
I have a rather large palm, but it was still too far away.
I'm super comfy with this thing in place!
It is adjustable in 6 levels, so you can also adjust it for winter gloves.
It can easily be slightly opened with the Dial adjustment.
View detail
Bought by color.
Bought it because it was closest to the OEM color Blue. It is easier to adjust than adjusting Wire because it allows for adjustment. View detail
Fits: HONDA CB400SF, HONDA CB400SF VTEC SpecificationsII, HONDA CB400SF VTEC SpecificationsIII, HONDA CB400SUPER BOLDOR
Aluminum Billet Lever
I bought this to change the color of the Brake and Clutch lever.
I liked the combination of Silver×Green Light and decided on Eukanaya.
I like the design and quality.
View detail
Fits: YAMAHA TMAX500, YAMAHA TMAX530, YAMAHA MAXAM
Also fits New ModelTMAX560
I installed it on my 2022New ModelTMAX560 and it fits perfectly. The GP Type is a little bit shorter than the Touring Type, so I thought I should have chosen the Touring Type, but I am satisfied. View detail
Fits: HUSQVARNA SVARTPILEN250, HUSQVARNA SVARTPILEN125, HUSQVARNA SVARTPILEN401, HUSQVARNA VITPILEN401
Lever with high texture
The packaging is secure and reliable.
From the moment you open the box and look at it, you can feel the quality of the product.
Installation took some time with Motorcycle's Habit, but was completed without problems.
Adjustment of play is also easy.
Love the color.
Use a Large cutoff to avoid breaking it in a standstill.
View detail
Fits: Others
Makeover.
I had a red adjuster that had been in use for about 5 years and it had faded, but I thought it looked a little childish, so I chose the silver one and it was the right choice. I chose Silver because I thought it would be a little childish, but I was right. The attached socket is thin and can be easily broken if you tighten it too much, so be careful not to overtorque it. View detail
Fits: KAWASAKI Z650, KAWASAKI NINJA650R
High-grade matte finish and easy operation
The OEM lever of Z650 looked like OEM, so I bought a U-KANAYA lever which has a good reputation. There were several different shapes available, but I decided to go with the Touring shape after testing it at a motorcycle supply store. The replacement took less than an hour, but when turning the nut of the clutch, the wrench did not go in, and it was a little troublesome to remove the switches, but the replacement was completed without incident. The cutout on the LeverReverse side was a little painful for my ring and small fingers when I gripped the Clutch, but it was not that bad. I thought it might hurt a little, but it didn't. It looks fancy and unbalanced in a good sense, and it is a good custom for beginners to tinker with motorcycles, so please try it. View detail
Fits: TRIUMPH StreetTwin, TRIUMPH STREET CUP, TRIUMPH SPEED TWIN 900
The length is …….
I bought it because it looked good on my previous vehicle and on my C125.
I chose the Short Type, which looked good on the C125, but this made it a bit …… difficult for me to do the Clutch.
Brake is so much better now, so I thought it would be good.
It has been a while since it was installed, but Clutch is getting used to it.
But …Short Type cannot be Recommendation for STREETTWIN.
View detail
Fits: KAWASAKI Ninja1000, KAWASAKI Z1000
Brake lever side is quite far away.
I installed it on my ninja1000 2019.
In the setting of Brake Side, I wonder if it is an individual difference, but I set the Lever to near the full quantity.:Set
It is quite far away.
It may be hard for those with small hands.
View detail
Fits: HONDA CBR1000RR, HONDA CBR600RR
Installed on 2021 CBR600RR
I was concerned about the BALI on the inside of the Lever, but I drive with Gloves on, so it's not a problem.
On the current CBR600RR, when the brake lever adjuster is set to 5 and the left side is fully open, it interferes with the chassis.
Stylish and I'm glad I bought it!
View detail
Fits: HONDA CB650F, HONDA CBR650F, HONDA CB650R, HONDA CBR650R
It is always UK-sanRepeat.
I have used many different manufacturer's levers, but UK's products are the most precise and have the best texture by far.
I use it because the touch feeling of Brake etc. is also Linear and very good.
View detail
Fits: KAWASAKI ZRX400, KAWASAKI ZRX400II, KAWASAKI XANTHUS, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR750 RS, KAWASAKI ZEPHYRX
Wide selection of colors
I purchased this bar end to replace the one I had originally installed. It took a little bit of time to install, but I was able to get it on without any problems. View detail
That's what I'm talking about!
I wanted to change from NORMAL to this product. There are about 4 different types, and there are many color combinations among them, so I was able to choose the one I liked best. The grip is comfortable and the texture is not cheap. (fits with cosmetics) There is no loss in purchase. View detail