Reviews
Fits: SUZUKI GSX250S KATANA, SUZUKI GSX400S KATANA
I purchased this product to repair standing moss.
I think there is a dress-up effect.
The feeling of use is normal.
View detail
a top rankingUp
[How is it used?
City Riding/Touring
Was the one you received as per Image?
The finish is as luxurious as the Image.
Was the installation difficult?
Oil Replacement Level.
How was your experience with it?
The Handlebar area will be a top rankingUp.
The SV650 has a severe sensor, so replacing the levers may cause errors.
It can be easily fixed by adjustment, but the Engine warning light comes on and I am in a hurry to find out what the error is.
View detail
Steady making
Anodized well and moderate weight.
It also seems to reduce Handlebar vibration.
Recommendation
View detail
Fits: HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA PCX125, HONDA PCX125, HONDA PCX125
Looks and feels good!
I installed it on my PCX (JF56). 6 levels adjustable from close to far with the adjuster, so it is easier to reach my fingers than the OEM Lever. I think the Long Type is more comfortable for PCX than OEM. My second daughter has small hands, and the OEM lever seemed to be a little hard to grip, so I replaced it with this one. After the replacement, she said that the Lever became well easy to grip.
You can choose from Standard Type, Touring Type, GPType, Foldable Type, and more.
We use U-KANAYA's Brake lever (GPType) in REBEL because of its good looks and texture.
When using with PCX, there are some points to keep in mind when starting Engine.
PCX does not start the engine unless the rear brake lever is held when the engine is turned on, but when this brake lever is replaced, the brake is not recognized as being applied unless the lever is held even tighter than the OEM lever, and the engine will not start. If the lever is held in the same way as the OEM lever, the engine will not start. Hey! What's wrong!" You might think.
View detail
The grip is easier for Large, but…
I bought this one because I had a double problem with NORMAL Lever being too hard and too far away.
It was easier to get a grip on it, but I didn't feel much benefit from loosening the Adjuster on the hard one.
I'm also concerned about the Adjuster on the Brake lever interfering with the Cowl when the Handlebar Lock is in place.
View detail
Fits: YAMAHA MT-10, YAMAHA MT-10 SP
Fits Clutch Side only
According to the description of the store that requested installation
The brake side of MT-10/2022~ is brembo and the structure of normal lever is different, so I was told that I could not install it as it is.
I wonder how it would be if one of the products with a conformity guarantee is unusable.
I was satisfied with the texture etc. of the Lever itself.
View detail
Fits: SUZUKI SKYWAVE400 burgman Type S, SUZUKI SKYWAVE400 burgman
SkyWave (burgman) U-KANAYA Brake lever
SkyWave (burgman) 250 SkyWave (burgman) I have also Customized 400 and connecting Brake lever.
I was able to install it on my commuter PCX150 with Universal Product's Adjust lever, but I was not able to install it on my SkyWave (burgman) The new system was almost impossible to install even with modifications to the
I bought U-KANAYA's Adjust lever because of the fit guarantee, and I am satisfied with the Large change because of the great fit.
I am so satisfied that the PCXAdjust lever that I liked so far seems so cheap.
I would highly recommend it to anyone who is considering Brake leverCustom.
I will continue to be a customer for Custom.
View detail
Fits: KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200R, KAWASAKI ZRX1100, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200R, KAWASAKI ZRX1100
Custom in Hidden Places
It's a place you have to look closely to see.
Self-sufficient Parts.
NORMAL rusts immediately after polishing.
This Parts will shine if you polish it.
View detail
Fits: KAWASAKI Z250, KAWASAKI NINJA2 Helmet50RR, KAWASAKI NINJA250R
Bi RedLever and matching colors.
NINJA2 Helmet50RRR that I found and purchased at my favorite dealer last October. (2012) I replaced the UK BiRedLever when I took delivery of my new bike. I finally found a UK Handlebar End in the same color at Webig, and immediately popped it in. It only took me about 10 minutes to replace it. I also purchased a 3D Logo sticker that I found on another online retailer. It's a little dress-up! It looks great. View detail
Fits: BMW R1200GS, BMW R1200GS Adventure
Very good product!
This product is combined with OEM Parts
The high precision of the workmanship and compatibility with OEM parts allowed us to assemble the product with confidence.
I have only done a test run and am looking forward to Touring!
View detail
Fits: HONDA CB1300SF, HONDA CB1300SUPER BOLDOR
Well made and satisfactory
I decided to buy it after I saw a friend of mine wearing it and was allowed to touch it. I like the fact that I can purchase each part individually in case of breakage.
It's still too cold to ride my motorcycle after replacing it, but I'm hoping that the operability has been improved.
View detail
Fits: HONDA CB125R, HONDA CB250R, HONDA CB150R, HONDA CB300R
Very easy to operate.
I felt that NORMAL was a little far away.
After replacement, we were able to adjust to the best position.
It became very easy to operate, and perhaps because of this, the Clutch operation feels lighter.
View detail
The finish is beautiful.
I saw a sample of a long lever of the same type in a store and felt that it was too long. I saw a sample of the same type of long lever in a store and felt that it was too long, so I bought a short lever.
The product is beautiful and I am satisfied with the workmanship.
The installation has been done with no problems at all.
As for Impression, it seems to be halfway long for my hand.
Although the position of the lever holder may have an effect, it feels longer than a short lever.
Short lever could have been a little shorter. I think it could have been a little shorter.
View detail
Fits: KAWASAKI Zephyr 1100, KAWASAKI Zephyr 1100
U-KANAYA Aluminum Cut-out Exotic Tote Flange
I had a hard time deciding between Kfac and Eukanaya, so I decided to go with the less expensive Eukanaya. I used to have a cheaper Flange with aluminum plating coating, but after 5 years of use, the plating was peeling off and it looked a little rusty, so I decided to use aluminum cut-outs this time. I will attach a photo so you can judge for yourselves! View detail
Fits: HONDA CB1100 EX, HONDA CB1100
I did not feel the difference in operability as much as I expected.
I know I chose a shape that was close to NORMAL. Levert is now lighter." I have not noticed any Large difference so far in terms of operability such as
Since we have not driven for a long time yet and used with Winter Gloves, the experience may change when touring long distances in the summer.
I am satisfied because my purpose is more of a dress-up.
Installation is easy as described in the instruction manual. Grease up may be necessary during installation.
View detail
Fits: HONDA CB1300SF, HONDA CB1300SUPER BOLDOR
Satisfied with the look and feel of the operation.
23' Installed on CB1300SB SP.
First of all, as a Single Item texture, Matte feels just right. It was neither too smooth nor too textured, which contributed to the feeling of a high texture.
There was of course no dimensional gap in the assembly, and the unit could be easily assembled.
As for the operation feel, first of all, the adjuster has a moderately hard click feeling, and even if something bumps against it a little, it does not easily gap. I was able to operate it without any discomfort.
This time, we chose a sober black color choice because the body is flashy, but we felt that it would work well as the one point of color with many choices, and would stand out in a prominent position.
View detail
stability
The Throttle is much more stable, stylish and cooler than the OEM! I even changed the Brake, Clutch and Throttle myself! View detail
Steady making
The product is solidly made and EXACTLY attached as it is specific to the car model.
The rest is just a matter of how the Anodized recession is progressing.
Since it is not a Chinese Manufacture, let's believe that it is Japan quality.
View detail
Fits: Others Touring typeLever
Used for Repair of standing stones
I purchased this product to replace a Lever of the same product that had been bent due to standing debris. I would recommend this product because it is less expensive than buying a whole new one, although you will have to use other parts.
I can also recommend it to those who want to change the color combination after purchase.
For disassembly and assembly, you will need the enclosed special Socket (thinner than usual), but please note that the insertion angle is 6.35mm. I purchased an adjuster with an insertion angle of 9.5mm→6.35mm separately due to the convenience of the ratchet I have on hand.
Instruction Manual is included, but I managed to assemble it by myself while referring to the work explanation video.
View detail
Parenthesis is great!
[How is it used?
Lever Replacement
One point
Was the one you received as per Image?
Yes
Was the installation difficult?
it is normal
General Maintenance Level.
How was your experience with it?
Coloring is so cool.
You can choose the color of the lever and the adjuster.
It is one point of reference and gives a different impression.
It is easy to grip and bring for long distance touring.
All previous generations of Motorcycles have been this Lever lol.
It just happened to have a color similar to Bar End.
I chose that one and it was perfect.
The color selection is quite confusing lol.
[Included Parts:were they on?
Yes
[Was there anything that disappointed you?
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail