Reviews
Nothing beats it, as long as you have the space to put it.
I bought a battered 900SS (900SL) and am Restore.
Everything is RoseRose until Bolt1 pc, then everything is Repair and modified and regenerated before assembly.
Stem bearings and other parts were also replaced, but since they are all RoseRose, it was easy to complete the work by simply turning the FrameSingle Body over and over while hammering.
The Ducati of this era had no dust or oil seals on the stem bearings, and the sliding surfaces of the bearings were exposed in a barbaric manner.
The bearing is really exposed, and even the bearing race can be seen when peering from below at certain angles.
The large washer, which was used in later models, was inserted into the lower side of the stem shaft.
Since it is just a Washer, there is no RubberRip seal, just a little harder to see Bearing and a little less gap with the Frame.
Still, I built it in thinking it would be better than nothing...
When assembled, the Washer effect does not look very promising.
On the contrary, it appears that foreign objects that have been placed on top of the StemBracket have become even more likely to enter the Stem bearing area.
I thought so, but the body is already pretty much assembled, and I don't want to remove parts now to make a FrameSingle Body.
Then there are two ways.
Lift the front of the body in some way or lift the body Front in some way.
The most stable method is to use a Jack or other lifting device.
The weight of the car body rides directly on the hard STAND, so it can lift TIGHTLY and Front.
But it often doesn't work that way, does it?
If it is a 4-cylinder engine, the exhaust pipe is in the way 100% of the time, and even if the exhaust pipe is removed, the oil pan is not flat on modern engines.
This is where the Frame Stand comes in.
As the name implies, you can put up something like a clothes-drying stand next to the Frame and use it like a clothesline.:Pair (for Left and Right) The Tie Down is hung by hooking the Tie Down to a stick passed through the
It is suspended by a string, so it is not very stable, but it is very easy to use.
This product is a super large version of the Frame Stand.
The maximum height of 2m is not a feat!
There is no doubt that the bigger the better, and this product is also much easier to use than the 1.5-meter Frame Stand that is often used by other companies.
It is so big and heavy that it has great rigidity, even when the body is suspended. The "feel" is a little bit like a "bounce. is Zero!
It is comparable to the high-performance STAND, which is sometimes used in motorcycle shops for PRO use.
The only weakness is Super big and super heavy." Things to do!
As you can see, it is a huge large when assembled!
Then I would say disassemble it after use...but no, no, no!
It will not stand on its own when disassembled, and even when disassembled, it is still big enough!
And since it's made of steel, it will definitely be covered in Rust if left outdoors...
in a word "Location matters." But [Color] The ability to Clear is the key to success.
If you are fortunate enough to have the indoor Space to store such a Giant Large item, this is a real treat.
View detail
L and U-shaped Attachment is Quantity:Great value for the set!
[How is it used?
I used to use a cheap Rear stand, but I am replacing it with a new one, and since I have several vehicles, both the L and U-shaped ones are available.:I was looking for something that could handle multiple vehicles with Set.
I would have preferred JTrip's, but they are quite expensive, so I chose this product.
Was the one you received as per Image?
The texture is not the best and a little cheap, but I think it is well worth the price.
It was also much lighter than the No Brand STAND we had been using, making it much easier to use.
The assembly is almost complete when it arrives, so all you have to do is adjust the height and tighten the screws.
How was your experience with it?
The body is light and the roller movement is smooth and light.
Usability is normal, but I am glad that it is lightweight, making it easier to maneuver within Garage.
[Points to note]
Hook is somewhat cheap.
If you are concerned about it, JTrip is a better choice. There is a price difference, so please consult with your Wallet.
Also, you need to bother with tools when adjusting the height, so that is MinusPoint.
How did it compare to other products?
It is easier to use than STAND, the No Brand product I had been using.
【Review】
This Rear stand is light and normally easy to use.
Not the best, but considering the price, I think it was worth more than the price.
View detail
Plenty of capacity! You can use it for the foreseeable future.
DAYTONA's Wire twister and Quantity:I bought it as a set
The product is of good quality, gives a beautiful finish, comes in a container, and is easy to use.
In addition, the generous capacity ensures that there is no need to worry about failure.
View detail
Easy Lift up
I had a hard time deciding between this and Jack's, but I chose this one because of its light weight.
Narrow type STAND is a little unstable, but it is stable when lifting the front.
When lifting both wheels or only the rear wheel, it is recommended to fix the Front with chocks.
This was the right choice for ease of lift up and portability.
View detail
Rugged STAND
It is BoxSTAND, Off-road motorcycle owners should have at least one.
I think it would be easier to put the Block under the Side Stand, tilt it to Left, and then put it in from the body Right.
BoxSTAND is so sturdy that once you buy one, it will last you a lifetime.
View detail
Unit Unit Silencer plug rating
4ST's Exhaust System has a thin end with a Silencer fixing Screw and a release bet.
I used to shave and modify it, but this Plug is not a good choice for me.
Exactly.
View detail
This is a great front stand.
This is a great stand for the price.
This is my first time using a front stand. It wasn't difficult to use.
After inserting the adapter that fits your bike into the front hook, hook it on your bike and lift it up.
It's quite sturdy and supports the bike well.
However, care must be taken not to scratch the front fender when using it.
I used it for gsx r1000 and there was no problem using it.
I highly recommend it to others as well. -------------------------------------------------- -------- It is a great stand for the price. I'm the first to use the front stand. It was not difficult to use. Put the adapter that fits the bike in the front ring and put it on the bike. It is quite strong and supports the bike. However, you should be careful not to scratch the front fender when using it. I used it for the GSX R1000, but there was no problem. It is highly recommended for others. Powered by Google Translator
View detail
Unit B2510 front stem-up stand
Tried it on a 2006 cbr600rr. There's no interference with the cowl, but you can't mount it the way you want unless you remove the horn. It interferes with wheel extraction, but try adjusting the height. View detail
Scooter Engine unloading is easy and safe.
I bought this to unload the Engine on my Scooter.
Front tire is fixed with steady STAND and rear frame is hung with 100kgClass Small Type Chain block.
The rigidity is high enough, and there are no problems at all. The construction and precision are high, and the bolt holes are perfectly aligned with the floor.:Pair (for Left and Right) The right angle of the legs of the "Rear" is also out and there is no tilt or rattling of the legs. The weight is not a problem for transportation, but in my case, I have to assemble and disassemble it each time due to the space in Garage, so I am a little concerned about the weight.:Pair (for Left and Right) It would be nice to be able to install the Hook on the
View detail
A must for anyone going on forest roads.
I bought this for Puncture repair when I go to the woods.
Convenient. That's all there is to it.
With some ingenuity, the front wheels can also be raised.
It is good to have a tube tire equipped no-motorcycle except for touring on forest roads.
I think its original use is for cleaning Chain, so if you don't have STAND, one is very useful.
There are also lifted ones, but they are bulkier and more sturdy due to their simpler construction.
It would be nice if it were a little cheaper, but I don't think it will break that often. If I had to say something, I would say that I wonder how long the Rubber will last.
View detail
Convenient to have
When making mixed Gasoline
Very safe and visual
It is easy to do the work of mixing liquids.
I'm glad I bought it
Oil Jug is now available in Quantities.:2pc. Set Use
We were mixing them up by transferring them to each other.
This way I can make 5 liters at a time.
Gas vent for expansion is also in the spout.
Caps can be used so that the liquid level can be
I've gained a lot of distance and have no blowback at all.
The oil inlet can be tilted by tilting the tank.
Because Gasoline flows in vigorously through the narrow gap
Mixes well even with hard Oil in a short time
View detail
Excellent cost performance.
[How is it used?
I use it with KSR2 and HAYABUSA.
Was the one you received as per Image?
It was smaller than expected.
How was your experience with it?
Chain maintenance is now easier.
[Points to note]
The GSX1300R HAYABUSAClass on Large motorcycles is dangerous for one person. An assistant is required.
(If you are using Front tireSTAND, it is Large sturdy by itself)
View detail
A great, inexpensive product that can do large jobs safely.
Used to replace rear suspension on ZrX1200 DAEG.
Although the product cost about $10,000, the synthesis was high and there was no anxiety at all during the work.
Very useful for Front up or RearUp.
I wondered why I had not bought it before.
It was easy to assemble and remove, and the Body was shaped to fit easily into Garage, so it will be used more and more in the future.
View detail
It is inexpensive but not cheap.
I use it on my NSR250R MC21 Racer.
It is a good product, inexpensive but solid.
The external cowl does not interfere with the external cowl, and the insertion into the stem hole is smooth and comfortable.
There is no Hook to hang the removed Caliper, but this is not a problem as a long S-shaped Hook can be used instead.
There is no interference with the Axle Shaft when changing wheels.
Since the Pipes interfere with each other when folded, it would be a good idea to stick some sponge rubber or the like on that area.
View detail
Costa is very good.
I use it on my Z125 and Ninja 650.
The Stem that fits both comes from the beginning.
There is no need to buy a special Stem for Mini bike separately for about 5,000 yen, like some domestic products.
The height can be adjusted to fit the Motorcycle, which makes maintenance very easy.
View detail
DL1000 V-STROM1000
I bought it to use on my DL1000 V-STROM1000, the Tire floated when fully extended, if it can be used on a V-Strom, I think it can be used on most Motorcycles, it is well made and strong. View detail
For Tire replacement.
Compact and foldable, it can also be used for touring.
Of course, it can be used at home for Tire replacement, etc.
By the way, when you float the front wheel, the rear wheel, the Tire
I am CRF250L and it looks like the picture.
View detail
In case of emergency
I was addicted to Motocross since I was young, but after 50 years old, it became too hard for me and nowadays I only do forest road touring with TRAIL car. I used to do Puncture in the mountains before, and I am used to changing tires on the Motocross because I used to do it often, but I only know how to remove the wheel by lifting the Motorcycle on the Motocross Stand lol. I had to replace the tube with a new one after I fell over the motorcycle and had a hard time. After that, I found this product and bought it as soon as I found it. I have been carrying it with me all the time since then. I have not used it while touring yet, but I feel safe. It would be great if it were a little lighter. I am glad I bought it. And as a side note, you must carry insect repellent during the mosquito season. I was attacked by a group of bush mosquitoes while repairing in the mountains. View detail
It works great! I couldn`t use it on my Rebel 1100.
I bought this product to try to maintain the rear area.
It can be used on GSX250R without any problem.
The Rebel 1100 could not be used because the Swing Arm and Exhaust System interfered with each other due to their proximity.
If I remove the Silencer Only, I can use it.
View detail
Cost performance is good.
It is more solid and secure than I expected.
The U-shaped part is deep enough to fit on the Stand Hook and prevent it from coming off, so you can use it with confidence. The color is black, so it goes well with motorcycles.
View detail