Reviews
Requires some ingenuity in installation
Quantity:Pair (for Left and Right) The end cap of the grip can be removed by pushing it out from the inside (not by screwing it on), but it is difficult to remove if it is stuck in the grip rubber well.
As others have mentioned, the wire winding diameter of the Throttle cone is about 2mm smaller than OEM, so that part needs to be modified.
I had originally cut and modified PVC Pipe to make it larger in diameter, so I did the same with this one.
The diameter of the part where the Grip Rubber is attached is the same as that of a normal Throttle cone, so it can be used without modification if there is no problem with the Throttle cone being low-slung.
The Left Side Grip was also press-fitted with a Throttle cone, so I was worried about installation, but this one had rubber on the inside of the cone, so it fit the outside diameter of the Millibar as it was, so after peeling off the original Grip Rubber, I lightly tapped it in and it went in. After peeling off the original Grip Rubber, I lightly tapped it in and it went in.
For the power supply, there was an Emon power supply extraction fuse of the same size as the Headlight fuse, so the Cable end of this fuse and the Wiring end on the Heater side were each modified and attached to the Bullet Terminal.
There was no place to install the minus ground, but a regulated rectifier was installed in the front cover, and its mounting bracket was a bare gold plate, so I loosened the bolt there and connected the wiring between the plate and the plate. The bracket was a bare Gold plate, so I loosened the Bolt there and connected the Wiring between the plates.
When the power is supplied properly, the Button glows Red→Green→Blue, so it was also convenient for installation to check whether ACC is energized or not.
The color of the Switch's Lamp is probably set to Red (strong), Green (medium), and Blue (weak) like many other things, but when I ran a test run, I felt that Blue was warmer than Green.
I am satisfied with the Switch as it is easy to operate and has a good texture.
Other reviews said the color of the Switch was Orange, but the one we received was Black.
I honestly did not expect it to be this good from the Body price, so I was disappointed in a good way.
I wish I had purchased it earlier.
View detail
Fits: その他 Vehicles with 22.2 mm handles
Could not install...
I was planning to install it on a BMW G650GS, but the Left Side was successfully installed, but the Right Side could not be installed due to interference with the brake hose. I think a large width modification is necessary for installation. I am sorry to hear that... View detail
Grip heater
The rotating part on the Axel side rubs against it, so it needs to be shaved off, and depending on the position of the hole in the accelerator wire, the outer circumference may be slack or tight. If you are a person who likes to tinker with Motorcycle, there is no problem, but if you are an amateur, it may be difficult. For me, it is a good product at a good price. I guess the only thing left to be considered is durability. View detail
Installed on K6 ADDRESS V125G
This is my first Grip heater! In conclusion, it required a rather tedious modification to our vehicle. I think it was a good purchase for me personally considering the cost, but 4 stars for the time and effort required.
[yeah!]
The texture of Grip Rubber is as good as famous brands. There is no sticky, shiny, sticky, etc. from a new product.
The integrated Throttle tube halves the problem of grip adhesion, which is the biggest problem when installing a Grip heater. (more than) I appreciate that you let me do this. I think it will reduce the number of failures and stresses after installation. Also, it is even more helpful for types with a projection on the throttle tube, such as SEA BASS type.
Almost imperceptible thickness:32mm (See image) Oh my!!! A certain D company is (albeit with a built-in Switch). 33.6mm and company K appears to be 33mm.
Warm even at the lowest setting.
[oh…]
Universal's Throttle tube required considerable processing…
It is the same big WaterproofCoupler as the old Hid Kit and may be difficult to handle.
The power consumption seems to be quite high, of course. "weak" Even when the rotation is increased, the Headlight darkens. (This is a full-wave rectification + lithium battery car)
A power supply similar to that of a batch direct might be desirable?
I don't know about other companies' products, but there are some parts where the heat wire is not covered and does not warm up. The angle is about 15°about…Grip fixing position may need to be devised according to preference.
There are many BALIs in each section.
View detail
Grip heater installation
Installed on ninja250 2018
I bought it with points because I had accumulated points. I didn't expect much because the price was cheaper than other products, but I think the result was more than the price.
When turned on, it heats quickly and automatically lowers the temperature as it warms up.
Late October morning I used it with summer gloves, too hot at low speed, but comfortable warmth when driving at about 50?/h.
There are only 3 temperature settings, but this is enough for me since I don't control the temperature frequently.
The Power Supply Cable of the Body is short, so it is supposed to be connected to the Cable around the Headlight, but since the DAYTONAD-UNIT was installed under the Seat at the same time, the Bullet Terminal was modified and the Cable was extended for installation.
Basically, you should be able to install it with just the parts inside the box.
Grip bond should be there because Left Side turns a little bit.
It's only been two weeks since installation, but I've had no problems with it.
View detail
Fits: その他 Vehicles with 22.2 mm handles
Surprisingly Matching!
I put it on to protect my hands from the wind and stepping stones.
Surprisingly MATCH to CROSS CUB.
Fire pattern decal is … sorry, I removed it.
View detail
Looks and feels great.
Installing the body is not difficult if you have experience working around Handlebar. The Plus is powered from the Meter light and the Minus is powered from the Headlight, the Minus wire is a little thin so be careful when handling it, be sure to install it properly. The Minus wire is a little thin so be careful with it. There are 3 levels of intensity and it works well. I ride it every day to work, and I'm sure it will get me through this winter. I'm not sure how durable it is, but I'm generally satisfied with it and think it's a good product. View detail
Installed on LIVEDIO More effective than expected
It is very good because it has three levels of difference and can be changed depending on the Situation.
The button is large and easy to push, and the wiring is soft and easy to handle.
For installation, anyone with a little knowledge of electricity should be able to do it easily, and I think bullet terminals or soldering is the best choice for wiring.
If I had to pick a bad point, I'd say it's the fact that you can't change the Button presses up and down in Quantity.:Pair (for Left and Right) It would be perfect to be able to rotate it the other way.
View detail
Mounted on Stunt vehicle
It is cheap like a toy. If you are not particular about the appearance, I think it is simple and does not get in the way.
Stunt vehicles don't have a lot of room, especially on the left side, so having a switch box like this helps a bit.
If you're not a fan of fiddling with Wiring, you might have a little trouble.
View detail
Wiring is reversed
I bought this product to customize my SUPER CUB, but the wiring of the Blinker was reversed.
I noticed it when I wired it and checked it. It's not much work to cut and solder the next wire again, but it was disappointing.
There is no problem with the use and appearance. The operation is also working without a problem.
View detail
Fits: その他 Vehicles with 22.2 mm handles
I can recommend it.
Even though it's inexpensive, the texture and performance are second to none compared to those of famous brands! However, I personally don't like the design of the Sticker very much.
Installed vehicle is HONDA:CRF250L (MD44)
I drilled holes in both grip ends and also drilled holes in the throttle end and installed it. You may need to change the Handlebar to Other Brand Product depending on your vehicle.
View detail
Check carefully before you buy……
My Motorcycle (MT09) This product does not seem to be attached to the
Because the shape of the OEM Clamp is not Straight, the hole of the mounting Screw did not fit.
It may be possible to change the whole Clamp, but ……then it may be better to make the Handlebar itself UP.
At any rate, it's not bad looking for the Gold amount, and the installation itself is a problem for Clamp. (Special shape) It would be quite easy if you don't have
I think the fact that the position of the handlebar can be easily changed in several stages is a good idea.
View detail
Fits: その他 Vehicles with 22.2 mm handles
It's a Universal Product, so it may need some work, but all in all it's good!
The sleeve for the iron handlebar is also included, so you can use it for both Aluminum and iron handlebar. This part needs some small work. A joint? If it interferes with hose clamps or wiring, the work of grinding is required. By the way, it was made in Taiwan.
View detail
Fits: その他 Vehicles with 22.2 mm handles
Cost performance is the best?
It is a solid build for the price However, there was a little difficulty in the installation, the Left Side came with no problem, but the Right Side came with no problem Because the Master Cylinder of Brake interferes with the Side, Kill I moved the switch and installed it
View detail
Fits: その他 Vehicles with 28.6 mm handle
Easy to use
I bought it because it was on sale at a super bargain price It was tapered and needed a bit of work, I put it on to protect it from the cold wind, but, well, you know Performance I'm generally satisfied with this product, although it's not what it was originally intended to be used for I think it will prevent damage to the Lever in the event of a fall View detail
Fits: その他 Vehicles with 22.2 mm handles
I think the costumes are good
The original price was incorrect, so I contacted the company and they corrected the price to the correct one, so I ordered I am very happy with it I'm very happy with the way it looks It looks good and I can't wait to install it View detail
Fits: その他 Vehicles with 22.2 mm handles
Solidly made for the price
All you need is a tool, and you can easily install it by inserting it into the Pipe on the Handlebar I started to install it, but I slammed it in with a Hammer with little diameter play There is almost no play and it will be fixed with Firmly View detail
Fits: その他 Vehicles with 22.2 mm handles
It is cheap but it works properly.
Quantity of Hand guard : In Set this price is amazing.
It was attached to us CRF 250 RALLY. Processing etc. There is absolutely no,
Quantity : Pair (for Left and Right) Mirror, OEMHand guard, including removal of all in 30 to 40 minutes.
There are many movable parts, and it was possible to install it with a nice feeling because delicate adjustment is also possible.
By the way, Handlebar used OEM as it was.
It did not hit Lever or OEM.
I think that it would not be a good idea if the forest road Touring position is ordinarily.
However, DesignSticker is pasted on only one hand guard, but from the edge
I was scattering off. I did not have any influence because I intended to take it from the original.
View detail
Fits: その他 Vehicles with 22.2 mm handles
Whether there is complaints at this price.
The price is also cheap, easy to match, it's perfect for Attack! Other Manufacturer is too expensive. I will attach it to other Motorcycle. Design is also satisfied View detail
Fits: その他 Vehicles with 22.2 mm handles
It looks tough.
It installed in SEROW 225.
Grip end to Cutteretc. Cut it or change it to Pierced Type Grip.
There is no Instruction Manual, but difficult processing etc.. I think that you can easily install it by loosening all of the Screws, positioning them, and then final tightening.
Since Bracket can freely adjust various angle of motion, it seems that it can correspond to various Handlebar.
You can install it without interfering with Lever or NORMAL.
Because it was cheap, I did not expect so much, but feeling that it seems to me Guard the hand with Frame and Frame other than improves it will enhance security. Because there is weight feeling which was slightly troubled, it may not be suitable for those who place importance on weight reduction.
View detail