Reviews
Requires some ingenuity in installation
Quantity:Pair (for Left and Right) The end cap of the grip can be removed by pushing it out from the inside (not by screwing it on), but it is difficult to remove if it is stuck in the grip rubber well.
As others have mentioned, the wire winding diameter of the Throttle cone is about 2mm smaller than OEM, so that part needs to be modified.
I had originally cut and modified PVC Pipe to make it larger in diameter, so I did the same with this one.
The diameter of the part where the Grip Rubber is attached is the same as that of a normal Throttle cone, so it can be used without modification if there is no problem with the Throttle cone being low-slung.
The Left Side Grip was also press-fitted with a Throttle cone, so I was worried about installation, but this one had rubber on the inside of the cone, so it fit the outside diameter of the Millibar as it was, so after peeling off the original Grip Rubber, I lightly tapped it in and it went in. After peeling off the original Grip Rubber, I lightly tapped it in and it went in.
For the power supply, there was an Emon power supply extraction fuse of the same size as the Headlight fuse, so the Cable end of this fuse and the Wiring end on the Heater side were each modified and attached to the Bullet Terminal.
There was no place to install the minus ground, but a regulated rectifier was installed in the front cover, and its mounting bracket was a bare gold plate, so I loosened the bolt there and connected the wiring between the plate and the plate. The bracket was a bare Gold plate, so I loosened the Bolt there and connected the Wiring between the plates.
When the power is supplied properly, the Button glows Red→Green→Blue, so it was also convenient for installation to check whether ACC is energized or not.
The color of the Switch's Lamp is probably set to Red (strong), Green (medium), and Blue (weak) like many other things, but when I ran a test run, I felt that Blue was warmer than Green.
I am satisfied with the Switch as it is easy to operate and has a good texture.
Other reviews said the color of the Switch was Orange, but the one we received was Black.
I honestly did not expect it to be this good from the Body price, so I was disappointed in a good way.
I wish I had purchased it earlier.
View detail
Grip heater installation
Installed on ninja250 2018
I bought it with points because I had accumulated points. I didn't expect much because the price was cheaper than other products, but I think the result was more than the price.
When turned on, it heats quickly and automatically lowers the temperature as it warms up.
Late October morning I used it with summer gloves, too hot at low speed, but comfortable warmth when driving at about 50?/h.
There are only 3 temperature settings, but this is enough for me since I don't control the temperature frequently.
The Power Supply Cable of the Body is short, so it is supposed to be connected to the Cable around the Headlight, but since the DAYTONAD-UNIT was installed under the Seat at the same time, the Bullet Terminal was modified and the Cable was extended for installation.
Basically, you should be able to install it with just the parts inside the box.
Grip bond should be there because Left Side turns a little bit.
It's only been two weeks since installation, but I've had no problems with it.
View detail
Fits: その他 Vehicles with 22.2 mm handles
Surprisingly Matching!
I put it on to protect my hands from the wind and stepping stones.
Surprisingly MATCH to CROSS CUB.
Fire pattern decal is … sorry, I removed it.
View detail
Looks and feels great.
Installing the body is not difficult if you have experience working around Handlebar. The Plus is powered from the Meter light and the Minus is powered from the Headlight, the Minus wire is a little thin so be careful when handling it, be sure to install it properly. The Minus wire is a little thin so be careful with it. There are 3 levels of intensity and it works well. I ride it every day to work, and I'm sure it will get me through this winter. I'm not sure how durable it is, but I'm generally satisfied with it and think it's a good product. View detail
Installed on LIVEDIO More effective than expected
It is very good because it has three levels of difference and can be changed depending on the Situation.
The button is large and easy to push, and the wiring is soft and easy to handle.
For installation, anyone with a little knowledge of electricity should be able to do it easily, and I think bullet terminals or soldering is the best choice for wiring.
If I had to pick a bad point, I'd say it's the fact that you can't change the Button presses up and down in Quantity.:Pair (for Left and Right) It would be perfect to be able to rotate it the other way.
View detail
Fits: その他 Vehicles with 22.2 mm handles
Cost performance is the best?
It is a solid build for the price However, there was a little difficulty in the installation, the Left Side came with no problem, but the Right Side came with no problem Because the Master Cylinder of Brake interferes with the Side, Kill I moved the switch and installed it
View detail
Fits: その他 Vehicles with 22.2 mm handles
I think the costumes are good
The original price was incorrect, so I contacted the company and they corrected the price to the correct one, so I ordered I am very happy with it I'm very happy with the way it looks It looks good and I can't wait to install it View detail
Fits: その他 Vehicles with 22.2 mm handles
Solidly made for the price
All you need is a tool, and you can easily install it by inserting it into the Pipe on the Handlebar I started to install it, but I slammed it in with a Hammer with little diameter play There is almost no play and it will be fixed with Firmly View detail
Fits: その他 Vehicles with 22.2 mm handles
It is cheap but it works properly.
Quantity of Hand guard : In Set this price is amazing.
It was attached to us CRF 250 RALLY. Processing etc. There is absolutely no,
Quantity : Pair (for Left and Right) Mirror, OEMHand guard, including removal of all in 30 to 40 minutes.
There are many movable parts, and it was possible to install it with a nice feeling because delicate adjustment is also possible.
By the way, Handlebar used OEM as it was.
It did not hit Lever or OEM.
I think that it would not be a good idea if the forest road Touring position is ordinarily.
However, DesignSticker is pasted on only one hand guard, but from the edge
I was scattering off. I did not have any influence because I intended to take it from the original.
View detail
Fits: その他 Vehicles with 22.2 mm handles
Whether there is complaints at this price.
The price is also cheap, easy to match, it's perfect for Attack! Other Manufacturer is too expensive. I will attach it to other Motorcycle. Design is also satisfied View detail
Fits: その他 Vehicles with 22.2 mm handles
Hand guard
I was wearing a Manufacturer's hand guard which I often see so far but it changed shape due to repeated falls and became to interfere with Lever. I am satisfied with making it cheaper to make than Guard. The shape slightly protruded outward in the outer direction became Large. The rest is strength, but I do not know because I have not fallen yet.
..
View detail
Nice design, good fit! I love shines the way ... It does not require conversion, easy installation. Very nice flashy design, look at everyone! I love WEBIKE!
Nice design, good fit! I love shines the way ... It does not require conversion, easy installation. Very nice flashy design, look at everyone! I love WEBIKE! View detail