Reviews
Recommended for those who enjoy Setting.
In case of analog type such as SR400, the effect of CDI replacement is (゜゜) I think.
Roughly CDI replacement.
The following effects.
1. Limiter can be disengaged. Electrical Limiter can be disengaged by installing an external CDI 。 The →SR has no limiter, so that's not the point.
2. Power, acceleration characteristics, response, etc. are improved over those with NORMALCDI. →Coil or Plug and Quantity:You can feel the effect when you use Set.
3. It maintains strong ignition power even at high rpm. It is beneficial to add →external carburetor, etc., as it will be closer to high rpm.
4. Remove Rotation Limiter. → I don't think this is relevant.
And this POSH has 4 types of ignition timings to choose from.
Map1 Angle of advance from NORMAL
Same as Map2 NORMAL
Map3 Delayed angle from NORMAL
Map4 LAGGER ANGLE THAN NORMAL
Says Rucksack Li simply 。 Power increases as the angle of advance increases.
Why is an advanced angle better? (Sometimes a slow angle is better)
When the engine speed is high, the crank rotation angle is too fast for the gasoline to ignite and spread, and the engine rotation angle and the gasoline spread will not match. 。 Therefore, at high RPM, it is necessary to ignite the ignition at a slightly faster timing than the angle of the crank (called "advance angle"), so it is necessary to control the ignition timing according to the engine RPM.
CDI in a nutshell, Parts to determine proper ignition Timing by Spark plug. The external CDI is designed to fully exploit the Potential of the target engine. The CDI is designed to optimize the ignition timing according to the engine displacement volume and tuning degree.
Currently I use Map1 or Map2.
Map1→When you want to turn GunGun.
Map2→Touring, etc.
good point
Installation is also easy with OEM and conversion.
○Idling is higher, so it is easy to be half-crazy.
The last seasoning, which is easy to feel the effect when changing the ○carburetor to an external one.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA Ape 50, HONDA XR50 Motard, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA Ape 50, HONDA XR50 Motard
6VMONKEY Maintenance Shift Arm Part Oil Seal
6VMONKEY Oil leakage from the oil seal of the change shift pedal gradually became a concern, so we replaced it.
The procedure is
(1) Apply a slotted screwdriver to the outer circumference of the oil seal currently installed and tap it to the center. (This work is important in case of sticking)
Screw the screw into the oil seal installed.
(3) Slowly pull out the Screw with pliers.
The oil seal of ShiftChange Pedal is thicker than other oil seals, so if the above method is also difficult, tear off the rubber around the shaft and pull out the gold part of the oil seal with radio pliers!
insertion
I used PVC pipe over a moderate flat washer.
View detail
Fits: YAMAHA TZR50, KAWASAKI ZEPHYR750, HONDA NSR50, HONDA NS-1, HONDA CB400SF, KAWASAKI ZEPHYR400, YAMAHA XJR400, YAMAHA RZ50, HONDA NSR250
One point custom
Purchased for One point custom color insert on the body of the car.
Each color is available so you can match it to your taste.
Clutch adjustment is easier because the rotating part is easier to turn.
View detail
เล็งไว้นานแล้ว พอดีมี point ส่วนลดเหลือเลยจัดทันที การจัดส่งแพคห่อสินค้ากันกระแทกมาอย่างดี คุณภาพสินค้าดีสมราคา ติดตั้งง่ายไม่ยุ่งยากถอดอันเดิมออกแล้วเอาใส่แทนได้เลย สั่งแบบเสียงโทนต่ำ ใช้เวลาในการจัดส่ง 15-20 วัน สินค้าน่าจะมาจากญี่ปุ่น โดยรวมถือว่าดี แนะนำครับ View detail
Used as a grapple when making your own Torque rod
Not high intensity or anything, just Material.:Stainless SteelM8Stud bolt.
Originally Stud bolt for SR400/500 Exhaust System, these parts are designed to replace the Rust-friendly OEM Stud.
I used it as a joint for making my own Torque rod for Brake, not for its original purpose, so I don't have an impression of it as an Exhaust SystemStud.
Since it will be used on a part that is exposed to high temperatures from the exhaust (which is why the OEM steel stud bolt will rust quickly and violently), I feel that stainless steel will seize and be difficult to remove next time.
After aligning the screw threads by putting a tap through the screw hole on the cylinder side, apply heat-resistant grease (thread compound) or the like before assembly, or you will likely face hell later on.
Even with a normal exhaust system replacement, the nut that holds the exhaust pipe flange is likely to burn out easily, so the use of a thread compound is probably a must.
What makes this Stud bolt different from other very inexpensive UniversalStuds is that the end of the Screw can be hung with a hexagonal wrench!
Stud bolts are usually attached and removed with a double nut that requires a bit of hang, or with a StudWrench, a special tool.
Material:I'm not sure about using it as an Exhaust SystemStud when it is Stainless Steel, but it would be good for those who cannot tolerate Rust.
View detail
Fits: KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200 Daeg
Parenthesis well with Blinker!
We chose this one because we thought it would be easy to install because we could divert the OEM.
The Blinker itself is a Level that can be quickly worked out with a single Driver. The Blinker itself was at a level where work could be completed quickly with a single driver.
The blinker relay requires the Bikini cowl to be removed, but it is an easy one to remove, so I was able to replace it without any problems.
The light intensity has been brightened by the change from OEM Valve to LED. I'm quite happy with the sequential as I often saw them on 4-wheeled foreign cars and admired them.
View detail
Fits: HONDA GORILLA, HONDA MONKEY
Pimp to Normal cab
It is used for the normal cab of LITTLE CUB. The air screw is hard to turn, but it is very helpful to adjust the idling easily when waiting for a traffic light, etc. View detail
Fits: HONDA CBR1000RR, HONDA CB1000 SUPER FOUR (Big One), HONDA CB1300 Super Four, HONDA CB1000 SUPER FOUR (Big One), HONDA CB1300 Super Four
When replacing the Exhaust System of CB1100etc!
[How is it used?
When we replaced the Exhaust System, we had to replace the Gasket as well, otherwise it would leak and cause power down.
How was your experience with it?
It is designed for CB1300, but can be installed on CB1100 without any problem.
Of course, the quality is fine and can be used without disposal leaks.
How did it compare to other products?
The cost performance is good because it is cheaper and of higher quality than OEM Product and KITACO's same etc. products.
[Points to note]
Note that if it has not been replaced for a long period of time, it will stick to the Engine side and scratch it if not carefully removed.
To prevent waste leakage, replace the exhaust system with a new one even if it is troublesome.
View detail
Fits: KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI ZRX1100, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZX-12R, KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI ZRX1100, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZX-12R
Posh Exhaust Gasket
I used it on my GPZ900R.
The price was low and it worked fine.
View detail
Fits: YAMAHA TZR50, HONDA NSR250, YAMAHA XJR400, YAMAHA RZ50, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, HONDA NSR50, HONDA CB400SF, HONDA NS-1
Gold's Clutch adjusterZ125pro
The Bolt is a little longer than OEM, but it came on with no problem at all. If you are considering this, please do so at your own risk.
[How is it used? Town ride
Was the one you received as per Image? Yes.
Was the installation difficult? Easy if you can lubricate the Clutch Wire
How was your experience with it? I think it has quite a dress-up effect.
[Included Parts:were they on? None
[Was there anything that disappointed you? None
Other items that would be helpful
Just work together when lubricating the installation points and hang/clutch wires.
Availability and clarity of Instruction Manual/A piece of paper is included, but it is a reminder to have it properly installed by a skilled contractor. This is fine, since the person who intends to install such a component does not need instructions for installation or use.
Notes/Nothing in particular.
Items to buy together/None in particular
Opinions and requests for Manufacturer/Good enough product.
View detail
m8Bolt to Fashion.
The m8Bolt is Fashion. The price is low, and the luxury is good. View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA livudio, HONDA Livdio ZX
Battery reply
I installed this on my MONKEY 12v Z50J because I rarely ride it and I feel the power is obviously stronger than the dead battery. View detail
Fits: HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA CROSS CUB50
ShininglyMaterial:Stainless Steel
The screw thread of the Chain Adjuster was stretched and felt stuck, so I purchased a Posh product from Other Brand Product instead of OEM.
Adjuster part is longer than OEM, but it is easy to replace.
Shiningly shining Stainless Steel is a nice touch.
Chain is small, so check it often and tighten it at the proper torque.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
To MONKEY's Overhaul.
I bought this for overhaul of my MONKEY. I had a hard time deciding, but I decided to go with this one because of the price. View detail
Fits: HONDA XR100 Motard, HONDA XR50 Motard, HONDA XR100 Motard, HONDA XR50 Motard
NSR50 being assembled
Used to install rear sprocket on NSR50. View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
For Monkey engine maintenance
I used it for servicing my MONKEY and it is a must have for Engine Overhaul. View detail
Fits: YAMAHA SR400, YAMAHA SR500, YAMAHA SR400, YAMAHA SR500
Outside Grip (Pierced Type) Convenient for installation of
Outside Grip (Pierced Type) It took a little time to fit the Accelerator Wire thailand core when replacing the throttle cone. View detail
Cap bolt with high universality.
[How is it used?
When I got my 25 year old PAT225WE, I bought it as a replacement for an OEM bolt (some of them I didn't know where they came from) that had been licked and tired at the corners after maintenance and restoration.
Unlike the steel BlackCap bolt sold at the local home centerretc., the Material:Stainless steel makes it easy to use for fixing the exterior and switches, etc., as it is resistant to rust, and is useful in various places.
Was the one you received as per Image?
As I mentioned above, it is a relatively MAJOR design bolt that can be purchased at home centers nowadays, and it is just like the Image product.
Was the installation difficult?
This is a type of bolt that is detached and attached using a Hexagonal Wrench.
If you have the dedicated tools, it is not difficult to remove and install the bolt, as the removal method is the same as that of the Others bolt.
I think it is becoming the next most popular after the normal convex hex Head Bolt!
How was your experience with it?
Although it is a bolt that is relatively easy to pick at, the stainless steel material makes it harder to lick than a steel cap bolt, and the black color makes it less noticeable when fixing switches and plastic parts, making it a very easy product to use.
[Included Parts:were they on?
There are no Included Parts:other than Bolt.
2 Bolts on Package Quantity:The product is sold in each length as a Set.
[Was there anything that disappointed you?
Basically, no.
At one time there was a lot of fuss about corrosion and gnawing depending on the type and characteristics of the Gold genus, but I'm an amateur and don't know much about it.
Other items that would be helpful
Point and hang of installation
It is a convenient bolt that can be used alone or in combination with the FUJI crucible type aluminum spacer.
[Notes]
As with any Bolt, please insert the appropriate tool firmly and deeply into the bolt before attaching or detaching it.
Failure to follow the above will lead to unexpected trouble, such as licking the bolt.
[ITEMS TO BUY TOGETHER
This is a Bolt only product (pack of 2), so if you want to use it where a Nut, Spring washer or Spacer is required, please purchase the necessary items separately.
[Opinions and requests to Manufacturer
Thank you very much for the lineup of various lengths. If you could reduce the price a little more, it would make it easier to purchase large quantities.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Amazing Top Bridge Dress Up Bolts
The quality is amazing with a great polished nickel look. I've included a photo for comparison. The supplied bolt is slightly longer and the countsunk has a larger surface area, I feel as though it's much stronger now. Would recommmend buying with polished top plate for a great look. Installation was extremely easy, I believe anyone can do it. Shipping was super fast from webike, always happy thank you webike! View detail
Fits: Others
Highly universal design like a certain manufacturer's OEMBolt
[How is it used?
I purchased the DRC Aluminum Spacer for M6 to go along with the SEROW225WE as a Bolt to match when used to secure the exterior of the SEROW225WE.
The following items are "DRCAluminum spacer and Quantity:The "State used in Set" will be in Review.
Was the one you received as per Image?
As the title suggests, it is a bolt with a Flange that can be turned with an 8mm size Socket or Wrench, I believe that this Flange makes the Large size fit the recess of the Aluminum spacer perfectly, which leads to the sense of unity when the exterior is fixed.
The product was as per the Image.
Was the installation difficult?
The method of use is no different from that of a regular bolt.
How was your experience with it?
I tried to match several different Bolts in combination with Spacer's Spacer made by DRC. Design without being too assertive." Several lengths are relatively easy to come by." Cost per unit performance." I have been using this Bolt in my Spacer vehicle since then.
[Included Parts:were they on?
There are no Included Parts:other than Bolt.
Quantity of 2 Bolts in a Package made of Vinyl:The product is sold in each length as a Set.
[Was there anything that disappointed you?
It is Uniqlo plating, so Rust may occur in some environments, but considering the mature design and cost performance, it is a sufficient product and I have no complaints.
Other items that would be helpful
Point and hang of installation
The aluminum spacer is changed to match the coloring of the location where the bolt is used, and the bolt length is the same as that of the OEMBolt.
[Notes]
Since the head part is 8mm in size, if the proper tool is not used, the corner will be licked and it will not be able to be tightened at the specified torque, and rust will easily occur.
Any Bolt should be carefully tightened or loosened using the proper Size tool.
[ITEMS TO BUY TOGETHER
Naturally, it can also be used with Single Body.
However, I think it will look even better when combined with an aluminum collar, as I did this time.
[Opinions and requests to Manufacturer
Thank you for the lineup of various lengths.:I would appreciate it if you could sell Stainless Steel products.
View detail