Reviews
Cheap, but not easy to use.
[How is it used?
Used for Engine O/H of TZr50R.
In particular, a universal holder like this product is needed to remove the fixed nut of the Clutch.
Was the one you received as per Image?
We selected this product because it had the lowest Gold amount.
To be honest, I thought the cheap price would make the product quite poor, but it was not as bad as I expected.
The supplier may be the same as the ones offered by other Manufacturers because the pictures are the same.
How was your experience with it?
The ease of use is not all that great.
In the case of TZr, the fixed pin is hooked to the clutch housing, but the fixed pin is short and easily comes off,
I cannot apply force well. I have the impression that the size is not right for 4EUEngine, although it may be just the right size for other Scooters.
[Points to note]
Be careful not to put the fixed Pin in the wrong place.
I used it on two engines and accidentally put a pin on the bolt hole of the clutch, destroying the bolt hole.
How did it compare to other products?
Similar products are lined up at similar Gold prices, as if the suppliers are the same.
Once you buy one, it will last a lifetime, so you might as well get something a little more decent.
View detail
Belt has no durability.
[How is it used?
I bought this for EngineO/H when Restore TZr50R.
I fixed the Flywheel with this product and removed the Crankshaft Nut and ClutchGEAR Nut.
Was the one you received as per Image?
The image was exactly as shown in the picture, and although there were several other manufacturers with similar pictures, Minimoto was the cheapest, so I selected Minimoto. I selected Minimoto because it was the cheapest price.
How was your experience with it?
The EngineO/H was successfully used and EngineO/H was successfully used.
However, Belt's durability was almost non-existent, and after a few uses, Belt's reddish coating was falling apart,
Although it can be used for a time, we worked with caution because shavings of the film could enter the Engine.
[Points to note]
When using it for engine O/H, the belt of the Flywheel side and the Holder must be degreased with parts cleaneretc. or it will not slide easily and cannot be fixed. Also, since the handle is short and it is difficult to apply the Torque, it is better to use a PVC pipe or similar to extend the length of the handle.
How did it compare to other products?
I have never used products from other manufacturers, but I have a feeling that the very cheap products sold on the Net are probably from the same supplier, so if you don't buy products from a proper manufacturer and price, you might as well buy Net products on the assumption that they will be crushed.
View detail
Not for groms.
Purchased for installation of High Camshaft on Grom, but it was too short to fix. View detail
For Scooter.
I purchased this product to replace the drivetrain on my Scooter.
However, I used it first for bore up work on a friend's SUPER CUB.
It works without any problems.
View detail
Good tool if used as intended.
This tool does what you want if you use it for its intended purpose. I bought the Husqvarna flywheel to hold while tightening the nut. Some said it failed and didn't do its job. Don't use it to change the oil filters in your car or load your ex-girlfriend's tire and it should work just fine. The safest non-destructive way to hold the flywheel for removal of the highly torqued nut. Could use a stronger clamping shaft to hold things while re-torquing the nut during installation. Bends a little too easily. Also, the vinyl coating on the band is slippery on a smooth flywheel surface. Powdered resin solves the slip issue. I've used this on a few motorcycles, Honda and Husky and it still looks and works as it should. I recommend it. View detail
Thoughts on using it
[How is it used?
Used to remove Clutch and Pulley from Scooter
Was the one you received as per Image?
No problem as per Image.
How was your experience with it?
I have not had any inconvenience at all.
[Points to note]
The holes are positioned in the most comfortable manner (opening angle), and then tightened and secured in place.
How did it compare to other products?
The product is not different in usability compared to the well-known manufacturer's product used in the past, and this product can be recommended because it is less expensive.
View detail
Convenient for everything
I bought this for maintenance of my scooter's drivetrain.
Until I purchased the Impact wrench, I had to hold the clutch outer with this product and remove it with the Ratchet wrench.
The plug-in type universal holder was difficult to use with the Clutch outer tightening torque, so I needed two types.
The price is very Reasonable and it is very easy to use.
I've been using it for about two years and it hasn't broken yet.
Now that I have purchased an electric impact wrench, I have less opportunity to use it on the drive train, but instead I use it around the crank and when removing the generator.
I feel that there are many opportunities to use it not only for Motorcycle, but also for cars.
Since it is variable and can be used for a variety of sizes, I think having one for now will come in handy later.
It is flat when placed on the ground, so it can be placed in the crevices of shelves, and I keep it hanging on the wall so it does not take up much space.
Sometimes when the lid of a bottle is too hard to open, I use this product, and it opens in one shot. However, be careful not to tighten it too much or it will break.
View detail
It's cheap and fully functional.
I purchased this product to replace the Reinforced Clutch and Reinforced Oil Pump on my SUPER CUB 50FI.
I was able to hold it firmly without any slippage.
It's cheap and large, and I'm happy with it.
View detail
good on cost
[How is it used?
TZr250R (3XV) I used it to remove the Flywheel of the generator of the "Mere Old Man" because it was rusty and I wanted to maintain it.
The Universal holder is available from various manufacturers, but I don't know the difference, so I chose this product which was cheap.
Was the one you received as per Image?
It is bigger than I expected. I was able to use it as soon as it arrived without any rust.
How was your experience with it?
I inserted it into the hole in the Flywheel and removed the Nut from the Center, but the retention was a little unstable and I wanted another hand.
Well, I was able to remove the Nut safely, so it did its job well enough.
TZr250R (3XV) To remove the Flywheel, you can also use the Puller (https://www.webike.net/sd/152021/) is required (I don't think it has to be YamahaOEM Product)
[Points to note]
Because it is a Universal Product, it is not a translation that hangs firmly, and it is necessary to hold it well so that the Holder may not come off.
I did some good work with my feet and stuff.
How did it compare to other products?
To be honest, unless it's from a Chinese manufacturer that you don't understand, I think it's the same no matter which Large body you choose.
It seems that the shape of the tool is slightly different from that of the tool manufacturer such as Straight, so it may be more stable... though it is expensive.
I thought this product, which was in stock and inexpensive, would be the best cosmetic option.
【Review】
These Items are required to Rose the Engine.
I thought it would be good to consider the one of the tool manufacturer etc. according to the budget because it comes out from various manufacturers.
This product was enough for me because I don't have so many appearances.
View detail
Convenient to have
Circular objects that used to be removed by various creative ways
This work was high torque, so I bought this one to keep my mind off of it.
If you find a limit that is not slippery, you can turn the large one, though you need a little hang for the degree of tightening for the one that is deformed or broken if you tighten it too much.
I regret that I didn't buy it sooner.
View detail
This is a must-have tool for anyone who does maintenance on their engines
It is used for maintenance of MONKEY series Horizontal TypeEngine and OEM Clutch and Flywheel are very useful for fixing rotating objects
However, because of the universal tool that presses down on rotating objects, the tightening torque is When you use this product, you can use it with no problem You can use it with no problem if you degrease it well
View detail
It's an outside item
I used it to hold up a Pulley on a moped
Please note that this product is an external product
It cannot be pinched like a Stag beetle
No rattling etc. and high quality
View detail
It didn't work, but it's a good cosmetic
I bought it as a Pulley off of co-MAJESTY, but as I feared, the Pulley It couldn't be used because it interfered with the back face fin But it's just an universal product, so it's not the same as the Clutch area It is a good tool to have because it can be used for motorcycle View detail
Universal fixture
I purchased this device for locking the pulleys of a scooter (maxiscuter) when unscrewing the nuts on the variator and torcdriver axles. I'm happy with the purchase! It is a very useful tool for replacing the variator belt. I purchased this device for locking the pulleys of a scooter (maxiskuter) when unscrewing the nuts on the axles of the variator and the torc driver. Satisfied with the purchase! A very useful tool for replacing the variator belt. translated by Google Translator View detail
MINIMOTO Universal Holder
MINIMOTO Universal Holder-A very good tool for locking the bell of the front or rear scooter variator when unscrewing nuts in a garage environment. View detail
It's inexpensive and very useful
I bought this one because I needed it to remove the flywheel from my MONKEY Most importantly, the price was low, so I went with this one
I've used it many times since I bought it and it's really useful because it's so easy to use and doesn't break
View detail
Used with Overhaul
I bought this engine for Overhaul this time GORILLA Engine. For the tool to be used for 12VEngine to remove Flywheel, since the pickup part can not be used in the tool which was used up to now, it was possible to remove it easily by using the newly purchased Universal holder.
It is mandatory for 12VEngine.
View detail
Really for 4 mini?
I bought it for use under the waist of AB27's Engine, but I could not use it. Firmly does not fit in the hole of Flywheel. If you use it Thunder etc. There is no choice but to shave the Arm part. It was useless shopping. View detail
To Scooter maintenance
Purchased for MAJESTY 125 maintenance. I did not have the Outer removal tool, so I am saved.. It was very cheap, so I am a little worried, but I still have to use durability from now on. Continue to use and understand something, I will write. View detail
It purchased for drive-system (Drive-face, Clutch) exchange of a Scooter.It was easy-to-use and working efficiency improved considerably.It is satisfactory.
It purchased for drive-system (Drive-face, Clutch) exchange of a Scooter.It was easy-to-use and working efficiency improved considerably.It is satisfactory. View detail