Reviews
Bad hole position in Bracket.
The position of the hole in the bracket was not good, so I could not put it on with a pop.
It looks like I need to widen the long hole in the Bracket or shave the Bracket.
I chose the latter.
I think the texture is quite good.
View detail
not bad, but ...
I think the cosmetics are better than OEM.
The plating is very clean at a glance, with no irregularities.
If you look closely, you can see vertical lines here and there that appear to be PRESS scratches? Vertical lines can be seen here and there during processing, which appear to be PRESS scratches.
I don't mind it much, but I guess those who care would be bothered by it.
There was no distortion or deformation, which is typical of Chinese Parts.
View detail
Blends in with nature like an OEM
I purchased this product to deal with a gap due to relocating Horn.
Installation is easy, but it is in the tedious category. It's a hard place to get to with tools.
It is a task that anyone can do if they are diligent.
The appearance effect is large, the texture is high, and the matching is so good that you would think it was OEM.
I like it a lot.
View detail
Rigidity, texture, and lightness are good, but be careful of interference when using with custom parts.
The texture is good for the price. I don't like the flashy shiningly, so the matte finish is good. The bar is also rigid and does not shake even when hanging the rear end of the car from the ceiling with a ceiling hook on this bar.
Please note the following customizations on your vehicle
The Daytona Carrierless kit interferes with the Carrierless kit. We solved this problem by cutting the interference part of the Carrierless kit.
GORILLA's SeatRear is a little bit closer to the back than MONKEY's, so the both ends of SeatRear interfere with the custom seat of the type in the picture.
View detail
Fits: HONDA APE 50, HONDA GORILLA, HONDA MONKEY
Normal use
I used it to install a Gorilla tank on my MONKEY.
Back side of Tank (Bolt tightening point) The OEM was one piece, but this is a split type, but no problem at all.
If I had to venture a guess, I would say that if you carry a tank with a split bush attached, the bush may come off.
There is some BALI, but not enough to be bothersome.
The OEM was quite soggy and may be replaced if there is an opportunity to remove the Tank.
View detail
Fits: HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY
delivery product
Thanks again for fast delivery I dont have to say something bud for yours I wait for next buy from yours shop keep up the good work offered View detail
I am very satisfied
Delivery is fast and I am very satisfied with the product. I have ordered so many products from Webike. However, these high-quality and in good condition products are really reliable. We recommend this product to those who love and like bikes. Reliable product, fast delivery, I am very satisfied with the result. I am very satisfied. I will order again and trust. Thank you. I love you. I will order today. Delivery is fast and I am very satisfied with the product. I have ordered so many products from Webike. However, these high-quality and in good condition products are really reliable. For those of you who love and love bikes, Now I recommend this product. Reliable product, fast delivery, very satisfactory results I like it very much I will order again and trust thank you Love it I'm taking orders today View detail
The front will be tightened.
It would look great on a Honda 4minifork! View detail
Fits: HONDA SUPER CUB 50, HONDA CHALY 70, HONDA CHALY 70, HONDA CHALY 50, HONDA CHALY 50, HONDA CHALY 50, HONDA SUPER CUB70, HONDA SUPER CUB70, HONDA CHALY 70
The cap on the gas tank on the Super Cab
The cap on the gas tank on the Super Cab Custom fit without problems. It twists very tightly and tightly, which makes it possible not to spoil gasoline. But there is no key - pay attention to this if it matters to you.
The photo shows the installed cover on the moped and also a comparison with the old original cover with a key.
The quality is average, but the price is also inexpensive. -------------------------------------------------- -------- The lid on the gas tank on the Super Caster Caster approached without problems. Spins very tight and hard, which makes it possible not to spoil gasoline. But there is no key - pay attention to it if it is important for you.
In the photo installed cover on the moped and also comparison with the old original cover with the key.
Quality is average, but also price is cheap.
View detail
Fits: HONDA APE 50, HONDA GORILLA, HONDA MONKEY
It's enough
You don't need to be concerned about OEM parts if they are this cheap, and you can install and use them without any problems. View detail
Fits: HONDA monkey, HONDA dachshund, HONDA monkey, HONDA dachshund
It might run out rather quickly.
I wonder if there is a winning Hagap. Is it worth the price? View detail
Fits: HONDA monkey, HONDA dachshund, HONDA monkey, HONDA dachshund
Price is right.
Is the quality of Rubber not so good? View detail
Fits: HONDA monkey, HONDA monkey
It can be used without loss with OEM. Cospa ◎.
I used this one on a 6V early GORILLA.
This is helpful because some OEM Parts have already been discontinued.
Quality is also OEM and no loss.
It's cosy.
View detail
Fits: HONDA APE 50, HONDA GORILLA, HONDA MONKEY
It can be used without loss with OEM. Cospa ◎.
I used this one on a 6V early GORILLA.
This is helpful because some OEM Parts have already been discontinued.
Quality is also OEM and no loss.
It's cosy.
View detail
Front face has been changed completely.
Easy to install on vehicles with ABS without modification. View detail
not bad
It is a Chinese part, but the plating is clean and can be used normally.
It also has a rubber cushion in the mounting hole.
View detail
Oh, I don't have a Copper Washer! Say goodbye to
[How is it used?
Every time I have a water or oil leak, I head to the nearest motorcycle supply store for an hour round trip to buy a Copper Washer from KITACOConvenienceParts.
I was wondering if there was a product that contained various sizes and I found this product and purchased it.
How was your experience with it?
220 Copper Washer are in a 100-weight container.
I was wondering when I would get around to using it, and I used the 6mm right away during maintenance the weekend it arrived.
It is a very normal Copper Washer. Of course, there was no leak etc.
But it gives me a lot of peace of mind. After all, there are 49 more sheets of 6mm Copper Washer alone. LOL!
How did it compare to other products?
Quantity from 1 till now:I used to buy 1 Set of 2pcs. of Copper Washer every time, but it is overwhelmingly safe.
I don't know if I'll ever use a 22mm Copper Washer in my life!
[Points to note]
Although there are many of these, there is no special Size, so it may be better to buy OEM Productetc. depending on the part to be used.
If you are in a situation where you can buy an OEM Product, there is no better way than to use an OEM Product.
【Review】
If you are a do-it-yourselfer, it's a good idea to have one so you don't have to run to the motorcycle supply store when you need it.
The basic Size is available, but if you can buy an OEM Product, buy an OEM Product.
View detail
The hole position is …
It was the first time for me to use Minimoto's product, but as other people said, the hole position was not correct and I couldn't fit the bolt. It seems to be no problem to use, but I would like to have it made more firmly. View detail
Bolt On is not an option.
I thought it looked sturdy, but when I put it together, the center was gapped and the screw holes were half off.
Also, all four of the Loader Hooks were welded at an angle … you should have made them a little better! It took me about 2 hours of tapping, bending, and scraping the cutouts while complaining about it.
My advice to buyers, if you can't fix it yourself, it's best to avoid it.
View detail
Versatile and easy to use!
An ordinary Washer.
But with so much variety and quantity, you won't have any trouble.
I used it for the Release exchange of MONSTER S2R this time, but I was saved because there was Size that fit Exactly.
It can be expected to play an active role in future maintenance.
View detail