Reviews
PWK Type" For?
I was looking for replacement parts for a carburetor that was not leaking gasoline and I thought it might be overflow, and I found this one. I bought it because I thought it would probably be useful.
Float Gasket and other packings can be used.
Float also has a different shape, but I think it is Large sturdy.
The kit includes a Needle and Needle Holder, but the Needle Holder is different in size and cannot be installed. The difference in the diameter of the bleed holes can be seen when they are placed side by side. I can't install it, but even if I could, I am afraid to use it. I was swearing to myself that I should put this on even without ChalkBoots.
Buyers should check their own PWK's Size before making a purchase to avoid disappointment. Please be careful.
The Gasoline leak was not fixed, although it was attached where it could be attached. We are continuing with the repair work because we were able to eliminate one of the negatives for the time being.
View detail
correction of post (to a post)
I made a Screw Pitch mistake in the first Review, so I am correcting it.
KEIHIN's Slow Jet was M3.5×0.6.
The Slow Jet included is M4×0.7.
View detail
The product itself is good. However, it is partly different from the product description.
The carburetor itself has a good texture and can be used normally!
However, there is a difference from the product description.
I thought I had inadvertently over-tightened the 1st pc. and the Throw Screw Pitch was crushed, so I bought another one of the same carburetor and noticed that the Screw Pitch was different between the #35 that came with the DeFault and the #35 that came with the KEIHIN PC20 that I had on hand&. hellip;.
Perhaps the Slow Jet that came with it is M4×0.7 and KEIHIN's Slow Jet is M3.5×0.5.
However, the screw threads are shallow and the pitch is slightly different, so the screw threads on the body side are crushed when installing and removing for setting.
Incidentally, the product description states that KEIHIN-made jets can be installed.
Main jet was also Large sturdy in KEIHIN.
If you are purchasing, please be careful
View detail
Not attached to JB03
The Bracket is no longer usable. I thought it could be attached to the current JB03 since it was indicated for JB02 and up, but I lost it. View detail
The "Kill" is required.
If you use it in Minimoto's Kit, it's not a problem, but …
Wiring modification is required when using OEMParts or outside the company.
There is no Wiring diagram and even if you see it, the colors are different, so you need to have some understanding to Large strange.
View detail
Bad hole position in Bracket.
The position of the hole in the bracket was not good, so I could not put it on with a pop.
It looks like I need to widen the long hole in the Bracket or shave the Bracket.
I chose the latter.
I think the texture is quite good.
View detail
Fits: HONDA monkey, HONDA dachshund, HONDA monkey, HONDA dachshund
It might run out rather quickly.
I wonder if there is a winning Hagap. Is it worth the price? View detail
Fits: HONDA MONKEY, HONDA GORILLA, HONDA DAX
Depends on STAND shape
It depends on the STAND to be installed, but the Spring of the STAND I tried to install this time was for Reverse side fixing, so I could not install it. View detail
high
Good design. Easy to install with Bolt On.
But it's expensive!
View detail
DAX6v
I'm wondering if you don't notice that the plating is already peeling off during the inspection process. I would not have bought it if it was brand new and the plating was already peeling off.
I don't think you should buy it, folks.
View detail
GarbageWaste Just buy it.
It was written in the previous instalment that it was broken immediately, or that it was crimped while seeing how it worked, but it is not a tool set for Chainfor Replacement in the first place.
As for the quality, it's not something that breaks immediately, so it's good. is cracked.
There's no such thing as a Pin for Crimp, even if you carefully put in a Plate, and it seems to divert a Pin for Cut, but I'm afraid!
The tip of the crimp pin is flat, so if you're not careful, the crimp part of the chain pin will crack and you'll have to start over from scratch.
There seems to be a reason for the low price, and I'd rather pay the same Gold amount to the store to replace it than buy this one, which is more reliable and secure.
You can use it as a Chain Tool, but you should consider that it can't do press-in and Crimp.
View detail
It didn't work.
I used it with the ELIMINATOR 250.
The Parallel twin's Carburetor is recessed and inaccessible in the on-board condition.
So I bought this Special Tool, but unfortunately it didn't work.
I thought the tip was about 90-degrees of flex, but it's actually about 100 degrees and a bit open.
This is why the Cell Motor under the Carburetor is in the way and cannot reach the Screw.
I don't think you can use the same type of Engine, GPZ, GPX, KLE, ZZr, because the carburetor arrangement is the same.
Well, to begin with, the later years of ZZr's have the Screw hidden by the Carburetor Heater plumbing, and no tool can reach it ……
I was disappointed because the quality itself is very nice.
View detail
It didn't work
It is the one that pulled out a thick aluminum plate, and uses the AquaPRO? of DAYTONA I bought it for the sake of it, but I ended up not using it because I had a surprisingly difficult time finding a place to install it
It's not that the performance of the product is bad, but it's a little bit large, and the angle of the foot is delicate You should think carefully before buying because of
If you have a Skill or tool that can cut out a steel plate, you may want to make your own
View detail
Too bad quality
4Quantity:I bought a Blinker from Set, and one of them has a 3cm long Lens Crack was found As soon as I found it, I applied for a replacement request Then, they responded quickly, and 3 days later, I received a package of 2 replacement lenses The Manufacturer sent it to me However, both of those pieces had Crack again It's not visible when you install it, but after installation, it cracks again due to the vibration of driving, etc I think there is a fear There are other Lens, but Small Sana Lack, Small Scratches, and in the manufacturing process I didn't even take the BALI that comes out Certainly not at a high price either "Cheap or not Then I don't think it's good enough Do you ship with a quality check? It's so bad I want to say it I will never buy anything from Minimoto again, except for the Lens, which is beautiful View detail
It's not a problem to use
First, my GORILLA is a 4 cm Long Swing Arm, 110-80-8Inch I cannot use DAYTONA 285mm Rear Suspension Spec I looked at the Impression and measured the Side Stand that is now attached to it and it was 175mm It is regrettable that there is no hole in the moving part of sensor, so it needs some processing It is View detail
Not worth $9,600
Please note In my Initial ModelDAX, you need to remove the Helmet holder to be able to The only thing I can think of is that it's not a bad thing It is a large red letter with a return shipping cost of 960 yen though the description of the product is insufficient It's a good thing that the direction of the hose connection of the Fuel Cock is not in front of the carburetor You shouldn't do this, but it's facing backwards, so the hose will be 180°UTurn If you want to install it on the Left Side, please use No.0841 ($8,100) There is no Fuel Cock, but it is still better because the entrance to the Hose is facing forward However, I think that the Helmet holder cannot be installed if I see it in the movie When you buy it, please consider well View detail
Not that great
This axle is low priced, which is great. But the finishing on the head looks terrible, and because of that I will not put this axle on my bike. So for me this purchase was a waste of money. I'm normally very satisfied with parts from Minimoto. They have low prices and you usually get great value for the money. I very much like the brand, but sorry Minimoto, this axle was a big disappointment. View detail
I can not recommend it except for those who can process it.
Socket's nail is broken and light does not light up Purchase.
The shape is almost the same as OEM
When the thickness of the electrode plate is 0. Thickness : 1 mm, because the gap between the electrode plate and the electrode plate is wide, it can not be attached as it is.
Also, like the OEM, there is no play in the hole at the base of the electrode plate, so it is not possible to move the electrode plate.
I diverted the old Parts and expanded the hole to make play, but it is easier to buy the OEM because it is troublesome.
View detail
Chinese made not good
Because I do not want to cut Harness of car Both Sides for LED installation, I bought it for processing but on the car of Both Sides's Connector
Terminal position is Gap and can not be inserted. Plating of terminals is also bad compared to OEM.
Give it up and buy an OEM.
View detail
Fits: HONDA GORILLA, HONDA DAX, HONDA MONKEY
Truly Chinese
Shopping for purchase unavoidably.
Miscellaneousness of details, badness of Fitting.
It was rumored..
The only good thing is that the price is cheap.
I do not think I will ever buy it in the same Manufacturer.
View detail