Reviews
Windproofing effect Extremely Large
Even OEMScreen's windproofing was generally satisfactory.
However, he purchased this product for further wind protection.
The installation was very easy. 30cm of distortion during molding was found in the vertical direction as a minus point.
The key windproofing effect is immensely Large. At high speeds it becomes (almost) windless. It may be hot in summer.
Also, the material seems to be acrylic, so I am concerned about deterioration over time.
View detail
I'm glad I bought it
The length was better than other companies' external screens because it was more windproof.
However, there is a possibility of interference depending on the installation position of the Smartphone Holder.
View detail
Parenthesis is good!
I was torn between OEMOption and ACRYPOINT.
I am glad we chose this one.
The texture is good and I think Parenthesis has improved on its own.
I'm glad I bought it
View detail
Good thickness to withstand STREET use!
I bought a battered 900SS (900SL) and am Restore.
Although battered, the visible exterior is relatively clean, with no cracks, cracks, or discoloration on the screen.
The body is 30 years old and has some minor Abrasion that may have been acquired during the process of use, but no problems that would require replacement.
I was going to use it as is, but ...
When I applied it to the car body under restoration, I found that it was distorted quite drastically.
I thought that the Screen of the Initial Model without Oil Temperature Meter was installed on the body of the Second Type Model with Oil Temperature Meter on the Meter, so the Oil Temperature Meter might have pushed the Screen and deformed it (in fact, the Oil Temperature Meter part was scraped off in contact with the Screen). I thought that the Oil Temperature Meter part might have been deformed by the Oil Temperature Meter (the Oil Temperature Meter part was actually scraped by contact with the Screen), or that the Mirror Bracket was bent and the Cowl was deformed when the vehicle tipped over, and the Screen was distorted by the bent Mirror Bracket. However, it seems that the Screen was distorted by the weight of some luggage that was placed on the Screen during long-term storage.
So, I replaced only Screen to try it out.
Fortunately, the reading was per Large and the distortion disappeared with Screen replacement.
In replacing the oil temperature meter, we should have purchased one for the Second Type Model, which has an Oil Temperature Meter, but this time, we dared to purchase one for the Initial Model, which does not have an Oil Temperature Meter.
The reason is that the Initial Model does not have a raised Screen and has a more beautiful connection with the front curve of the Cowl.
The design of any car model must be an Initial Model that the Designer thought was the coolest!
I think that the beauty of the model when viewed from the side is spoiled by the Second Type ModelDesign with a raised Screen because the Oil Temperature Meter is retrofitted to sell the product and the Screen makes contact with the product as it is.
However, the Oil Temperature Meter in question is violently contacted as it is.
I'm shaving the Meter side of the contact area, but I guess people usually don't like to shave ...
The Second Type Model's raised Shield is also more windproof (the Screen for the Initial Model is much lower), so it is also suitable for normal use.
Since the mounting dimensions are interchangeable, it is recommended to use the Second Type Model with or without the Oil Temperature Meter for touring applications.
However, it is only the Initial Model that is completed in terms of design!
ScreenMaterial performance is unquestionable!
I would have preferred a thinner, more transparent and distortion-free ScreenCraft product, but unfortunately Webike does not carry it.
I gave up on the ScreenCraft product, which is characterized by BALI nko cracking in one shot when it falls over, and went with the more sturdy ACRYPOINT product, but there are no problems at all with transparency or distortion.
It is obviously thick and sturdy, so I don't feel that it will always crack if it falls over like ScreenCraft.
The hole positions did not match, but this must be a problem on the DUCATI side.
Even if it does not fit, it is only about half of the Screw diameter, so a little shaving with a round file will do the trick.
In particular, the 900SS is a spec. that is fixed with a well nut, so it does not matter if the gap is a little low or high.
View detail
Parenthesis is a good idea
I purchased KATANA and this is my first Custom.
Since Screen is small in OEM, the Type of Long is used.
Installed.
I don't know about the aerodynamic effect because I haven't driven at high speeds yet,
I like the new look and feel of Parenthesis very much.
I am happy with this Screen purchase!
View detail
Satisfied with both appearance and effectiveness
By changing to a long screen, the amount of wind received by the body was eased, making high speed cruising easier.
I am satisfied with the appearance, which is better looking than the NORMAL.
I set it to Smoke Screen, but there is no inconvenience of blocking the view, etc.
View detail
It will be more windproof, but it will be a little firmer.
For 2011 MODEL (8BK-MC51) Windshield of.
The high transparency and lack of distortion are as expected from JAPAN alone.
To install, simply remove the four screws on the side of the screen and pull it while sliding it backward.
This product comes with the Rubber Bush for installation, so there is no need to remove the Bush from the OEM, just reuse the OEM Screw to secure it. I was able to install it without feeling like it was going to crack like other Reviews and without any Gap in the Screw hole.
No problem with machining accuracy.
The OEM product is designed to be flush with the cowl, but this product is designed to be under the cowl, so there is a difference in the thickness of the cowl. It would be great if the two were flush, but since the manufacturing process is different, it would be difficult to achieve this.
The test run felt that the wind protection was quite effective.
The wind pressure against the body is considerably reduced, and before you know it, the speed has increased.
Wind noise emanating from the Screen and Cowl is not perceptible, but unfortunately I did not get the impression that the sound felt through the Helmet was any smaller. Still, I think that fatigue after a long-distance run will be lessened.
Also, the standing screen may be due to the load on the front due to wind resistance, which reduces the fluttering sensation and makes it more difficult to turn the wheel.
Originally, the front of the '23 model had a sturdier feel, but it now feels as if it is about 10% heavier.
Styling-wise, the +6cm height of this product gives a rather smoky feeling depending on the angle of view, so it would be very well put together if it were lowered by about 2cm more. However, the limit is not broken, and as you get used to seeing it, it seems to match the CowlDesign of the 23rd model, which has increased volume.
Based on the above, we can say that the satisfaction level is high from the balance of the experience effect and the change in Styling.
View detail
Good quality and cosmetics
Higher and more rectified than OEM
High-speed driving is now easier.
ScreenBody and the dedicated PlasticRivet are
It will be attached.
Remove all OEMScreen, screws, etc. for installation,
Simply attach this product by following the reverse procedure.
Only the supplied plastic Rivet is used for fixing. At a glance
It looks unreliable, but in fact it can be firmly fixed.
When assembling this product to the vehicle body, the hole position is slightly gapped.
There were some parts that needed to be repaired, but not to the extent that they require modification.
The work can be completed in 10 minutes.
● Protective Film enters the Rubber Mall at the edge of the
But if you pull off the Film as usual, you can get a good result.
Film can be peeled off without leaving the molding intact.
The instruction manual is not included in the package, so that's a no-no.
View detail
It looks good
The OEM Product has almost no wind protection effect, so it was tight when touring, but thanks to the 6cm higher height, the wind exposure seemed to be reduced. However, the clasp is a little too small and does not stop properly. View detail
Happy!
I was satisfied with the quality of Visual, as well as the security of JAPAN. View detail
Race ish
Purchased because OEMScreen is low.
When I used the Circuit and got down in Straight, the OEM had a poor view through the Screen, but after the replacement, it was easier to see.
Installation is relatively easy since all you have to do is remove the OEM Screen, Bolt, and Nut and install this product with a push rivet.
View detail
Stable and secure JAPAN!
The only one available for the 2023MODEL, the Smoke Screen, although not an option, is a solid Brand product, so the quality is perfect. The smoothness of the surface, the lack of distortion, the mounting holes, the precision of the chili, it's perfect.
WeBig was out of stock, but we had to wait less than a week for delivery after ordering. That's another great point.
The facial features have been tightened and the impression has changed dramatically.
View detail
It will look cool.
We replaced the poor OEM Screen as the first dress-up when we took the car in for servicing. I am not sure if the wind protection effect was improved, but it looks very cool and I recommend it. View detail
Perfect hole position
[How is it used?
We used this Screen in combination with MC21's Saiya Cowl.
We were worried about OEM used products and TIGERPerformance's Screen, but we chose this product because of its shape and transparency.
Was the one you received as per Image?
It arrives with a protective film attached to prevent small scratches until installation is complete.
It is also quite transparent.
Was the installation difficult?
Installation is easy
The hole positions were perfectly aligned with those of the Saiya Cowl, so there was no need to modify them.
I also used a Nylon rivet from KITACOConvenienceParts because it had an M4 hole and I did not have an OEMRivet. (https://www.webike.net/sd/1343087/)
How was your experience with it?
The shape is a matter of personal preference, but I personally think it is a good length.
The transparency of the ScreenBody makes it look good.
[Included Parts:were they on?
This is the only product, so an M4 Rivet is required if needed.
[Was there anything that disappointed you?
Not at all!
【Review】
I was concerned about the accuracy of the mounting holes since it is an external Screen, but there were no problems at all.
The transparency is quite satisfactory.
View detail
Total and good ACR-POINT domestic Screen (Price, Quality, Application)
[How is it used?
City ~Touring ~Circuit
Was the one you received as per Image?
Just the right size, 5cm up from NORMAL height
Was the installation difficult?
One Driver is all you need
The position of the mounting holes are gapped and need to be adjusted (depending on the individual).
Originally, Material:Since the plastic screws and the female screws of Rubber Bush are installed, the risk of breakage due to aging is large, so the NORMAL material is used separately.:It would be a good idea to order PlasticScrew and Rubber Bush female screws and replace them at the same time.
How was your experience with it?
When driving at high speeds of 100km/h, in the normal riding position, the wind flows from the neck to the upper helmet, providing good wind protection.
In addition, the windproof effect from the forward leaning Position and
Visibility through the Screen is good with no distortion.
View detail
exchange of new products
I thought about renewing the screen, and considered the inexpensive Thailand moth screen, but I was concerned about its accuracy, so after much deliberation, I decided to go with ACRYPOINT's ClearScreen. I was worried about the accuracy, so I decided to go with ACRYPOINT's ClearScreen. I was relieved to find that the product was almost OEM and solid. I am looking forward to installing it! View detail
change one's mood
Net only lists certain angles, so I added them. View detail
ACRYPOINT with a proven track record in Race!
It is not RACING but For Street, but the shape is the same as other manufacturer's RACING and it has a braid for Japanese Vehicle Inspection Correspondence, which is perfect for me who enjoys circuit driving. It is an exact product for me as I am a Circuit driver.
When you get down at Straight, the rim is just at eye level in OEM, so it is 5 cm higher than OEM, so visibility is likely to be better.
The Helmet is not in the way when it is in the prone position.
We are a Manufacturer with a proven track record in Race. [Color] I am also pleased with the clarity of Clear.
Also included is a new well nut, which is kind.
If I had to say something, I would say that the attached Sticker is Quantity.:1 pc. only
Quantity:Pair (for Left and Right) I would have been happy if there had been two pieces in the
View detail
Love it!!!
Love the windscreen, and clear acrylic visability. Brings the laminar trailing edge closer to the riders helmet. Grealy improves functionally for shorter riders with wind protection and improves aerodynamics with its sleek design. I rate this product a solid 10. View detail
How nice
Windproof effect has been increased considerably.
In OEM, you can get down to your eyes full of Tanks.
Helmet dizzy from wind pressure at high speeds
I used to do this, but since I switched to this
Very stable
View detail