Reviews
Fits: その他 GT-air II, その他 Z-8, その他 NEOTEC II, その他 J-FORCE IV, その他 J-Cruise II, その他 VZ-RAM, その他 CT-Z, その他 SZ-G, その他 F-17, その他 AERO BLADE V, その他 KAMUl-III, その他 SHUMA, その他 RYUKI, その他 EXCEED, その他 AVAND II, その他 A-FORCE RS, その他 G-FORCE SS, その他 FF-COMFORT, その他 A-FORCE RS JET, その他 G-FORCE SS JET
The sticking range is also good and wide.
It is considered an excellent object, although it is not completely in the rain and not during the cloudy winter months. The price, too, is not bad. View detail
It doesn't fog up!
Fitted on a Simpson Helmet. It will not fog up!
It is the Large size that no longer opens the Shield.
It can't be helped, but since it is not a dedicated product, the frame is in a narrower position than Shield and the view seems to have been reduced.
I'll use the non-fogging Merit as it is since it's Large.
View detail
Fits: その他 GT-air II, その他 Z-8, その他 NEOTEC II, その他 J-FORCE IV, その他 J-Cruise II, その他 VZ-RAM, その他 CT-Z, その他 SZ-G, その他 F-17, その他 AERO BLADE V, その他 KAMUl-III, その他 SHUMA, その他 RYUKI, その他 EXCEED, その他 AVAND II, その他 A-FORCE RS, その他 G-FORCE SS, その他 FF-COMFORT, その他 A-FORCE RS JET, その他 G-FORCE SS JET
The comfort of forgetting that Shield is foggy
Used for System helmet.
First of all, it is pasted, but it can be pasted after positioning with the included pattern paper.
Rubber packing is attached to the top and bottom of the helmet's shield.
It was necessary to correct the position several times so that the Seat would not hit it when opening and closing the Shield.
This Seat can be reapplied, but if you repeat it too often, you might damage the Seat or the adhesive.
If possible, it would be better to limit repasting to the smallest limit.
When the Shield is opened, the Seat hits the upper Rubber packing and the Seat, so the Seat is affixed much lower.
It still hits a little, but I am able to open and close it anyway.
The anti-fogging effect is excellent.
It is so easy to completely forget that Shield in winter is supposed to be cloudy.
Apply anti-fogging protection every time you use the Helmet and
Still, it was completely free from Stress and danger that clouded over time.
How much better is A.P. RFilter's effectiveness compared to other anti-fog Seat
This is my first time with this Seat so I can't compare.
On the downside, depending on the light, one's face (nose) can be quite visible inside the Shield.
At first I was surprised and thought my view might be obstructed.
Once I got used to it, I didn't mind.
Also, there is a smell of Material for a while, but it will disappear naturally after a few days of use.
The care is said to be peelable and washable, but as mentioned, we don't want to do this too often.
The inside of the Seat is not smooth and is not likely to be wiped with a cloth etc.
I am trying to figure out what to do when it gets dirty.
The Logo printed on the Seat is cool and I feel as if my inexpensive Helmet has been upgraded.
View detail
Fits: その他 GT-air II, その他 Z-8, その他 NEOTEC II, その他 J-FORCE IV, その他 J-Cruise II, その他 VZ-RAM, その他 CT-Z, その他 SZ-G, その他 F-17, その他 AERO BLADE V, その他 KAMUl-III, その他 SHUMA, その他 RYUKI, その他 EXCEED, その他 AVAND II, その他 A-FORCE RS, その他 G-FORCE SS, その他 FF-COMFORT, その他 A-FORCE RS JET, その他 G-FORCE SS JET
Not hard and easy to apply
First of all, I cannot evaluate the adhesiveness and durability of the product because it has not been used for a long time.
I got interested in this product and used it for CJ-2Shield, Helmet is JCruise
I had an OEMPin lock, but I saw the performance degradation, so I dared to use a replacement.
As advertised, it is a very flexible material and was easy to apply.
A paper Seat for positioning is included in the product, as well as a protective film for the Seat.
The center line is kindly indicated, so there should be no confusion about the pasting position.
The key is the anti-fog performance, but there seems to be no particular difference from the OEMPin lock, so there are no concerns.
The function "A.P. RFilter" is only used on level ground, so I can't really feel it so far.
It is said to be durable and easy to apply and remove, so expect good Maintainability in the future.
View detail
Fits: Others X-Fourteen, Others GT-air II, Others Z-8, Others NEOTEC II, Others J-FORCE IV, Others J-Cruise II, Others HORNET ADV, Others RX-7X, Others ASTRO-GX, Others RAPIDE-NEO, Others XD, Others VZ-RAM, Others CT-Z, Others SZ-G, Others F-17, Others AERO BLADE V, Others KAMUl-III, Others SHUMA, Others RYUKI, Others EXCEED
Installation is quite difficult.
This is a type of anti-fogging Seat that is not a pin lock but a stick-on type.
The ARAI CT-Z Pin Lock Seat I am wearing is missing (maybe it is an old MODEL and is discontinued?). I am looking for a new pin lock seat for my ARAI CT-Z.
This is why we chose this one.
The effect is decent.
The Shield is attached with adhesive resin that surrounds the Shield, but positioning is quite difficult.
I can re-cover the surface, but I don't want to leave fingerprints on it, so I want to do it in one shot if possible.
There is a pattern that can be used as a guide, but it is quite difficult.
The installation itself is easy, but you need to prepare properly. Be courteous and bold." It is recommended that you stick with it.
Therefore, it may be suitable for dexterous people.
View detail
Used on a Simpson DiamondBack. It doesn't fog up.
[How is it used?
Used for Simpson DiamondBack.
Purchased this one because Pin Lock Seat is not available.
Was the one you received as per Image?
There was no problem with the image as it was.
almost [Color] Clear, but it looks like it has a little bit of color when you put it on.
How was your experience with it?
As for the anti-fog feature, it is very good.
It was comfortable to use.
As for visibility, the rim is inevitably in view.
This is somewhat concerning in Simpson, where even free visibility is poor.
It is necessary in winter, but it is better not to have it in summer.
I own another Helmet from WINS and have been using it for about 3 years for commuting.
About halfway through the second year, the surface of the fog WIN deteriorated and the visibility became finely wavy.
Depending on the frequency of use, it may be advisable to replace them once every few years.
Adhesion seems fine and has not peeled or fogged up.
[Points to note]
Since it is a universal product, it is slightly smaller than the Shield.
Given the large size of Simpson's Eye Port, this may still be the limit.
If you put it on the upper limit, it may interfere with the opening and closing of the door, so it may be better to leave a little room.
How did it compare to other products?
Pin Lock Seat is also used on another Helmet.
While new, I didn't feel any superiority between Fog Win and Pin lock.
I thought the durability of Fog WIN seemed to deteriorate visibility more quickly.
Pin lock also had a gap early on and sometimes fogged up even after adjusting the Pin, so I can't say for sure.
Point and hang of installation
If you put it too high up, it is prone to interference.
[ITEMS TO BUY TOGETHER
Shield without pin lock support
[Opinions and requests to Manufacturer
I would appreciate it if it were cheaper so that I could easily replace it.
View detail
Comparison with PINL ◯ CK
Mounting on YJ-17 ZENITH-P
Originally I used PINL ◯ CKShield as it was used, but as the adhesion strength fell in about a year and a half and gaps became possible in Shield, I tried to replace it, in any case I thought to try FOGWIN
Below, comparison with PINL ◯ CK
【attachment】
PINL ◯ CK is more Pin and its position is determined so you do not have to worry
FOGWIN is a little troublesome to paste alone
I asked my bride to spread the Shield and pasted it
Positioning is not difficult as Template can be applied as a guide, but if you look at workability simply PINL ◯ CK is better
Instead, FOGWIN is free to some extent at the pasting position, so it is better to choose a person with a forward tilt upwards, a person with an upper body awake lower, and so on
Although it seems that it interferes when opening and closing the Shield when attached to the eyes too much, it did not interfere with the part installed at the same height as PINL ◯ CK
【Adhesion strength】
Obviously above PINL ◯ CK (Naturally)
I have not peeled off yet, but it seems quite Large seems to peel off
【Performance - function】
None above or below PINL ◯ CK
Antifogging performance will not change at all
There is information that there is irregular reflection saying, but there is also no difference between PINL ◯ CK and Large
【Summary】
I think that there is no performance difference with PINL ◯ CK at all
Because the price is almost the same, I wonder if you can choose whichever you like
However, since PINL ◯ CK can not be installed unless it is a compatible Shield, people using non-compliant Shields are unnecessary and here
As to how long it will last, I'd like to use it for a while
I'm happy to have 2 Season
Once, that part (Durable) Because I am unknown, I am decreasing one star
There are no dissatisfaction points at the moment
In the coming season, the shield's cloudiness is a problem that can not be neglected in terms of both Stress and safety
If you are using a PINL ◯ CK compliant Shield, we recommend that you install FOGWIN
View detail