【WINS】FOGWIN general-purpose mini F01 Review
It doesn't fog up!
Fitted on a Simpson Helmet. It will not fog up!
It is the Large size that no longer opens the Shield.
It can't be helped, but since it is not a dedicated product, the frame is in a narrower position than Shield and the view seems to have been reduced.
I'll use the non-fogging Merit as it is since it's Large.
Responses
Other reviews
FOGWIN
My impression of wearing it on SIMPSON's RX-10 is that it gets stuck when opening and closing the Shield. I think this takes some getting used to, but I didn't mind it too much. I think this is something you have to get used to, but I didn't mind it too much. View detail
This is the best
Used for AraiTour cross
ManufacturerOEM Parts interfere when opening and closing, even though they are exclusive parts.
This product is totally stress-free. And it's easy to reupholster.
Although often neglected because of WINS, FOGWIN is above other manufacturers.
I think it is PARTS.
There is a slight chemical smell, but it disappears after a week or so.
I chose Standard because it is AdventureStyle's Shield.
If you can put up one for Adventure, I'd like to try that one too.
Quantity:Pair (for Left and Right) If that bothers you, you can see the edge of the Seat on the underside of the
It wouldn't have been suitable for driving on public roads in the first place.
View detail
Interference with M30 Clear shield
I used it on my M30 Clear shield and it interfered when raising the Shield up.
I thought I had pasted it too far up, so I tried pasting it at the Limit where it interferes with the bottom, but it interferes with the top again, and it opens to open, but gets stuck.
I thought it was Large sturdy because it managed to open, but the adhesive on the stuck part stuck to the Shield and Helmet and left marks even after wiping.
It is too much of a quandary, so I cut off the part that had adhesive on it due to interference and used it once, although the anti-fogging performance will be reduced.
Clear shield does not remove stains and I am thinking of replacing it.
It really sucks. I want my money back for Gold and Clear shield.
View detail
Used on a Simpson DiamondBack. It doesn't fog up.
[How is it used?
Used for Simpson DiamondBack.
Purchased this one because Pin Lock Seat is not available.
Was the one you received as per Image?
There was no problem with the image as it was.
almost [Color] Clear, but it looks like it has a little bit of color when you put it on.
How was your experience with it?
As for the anti-fog feature, it is very good.
It was comfortable to use.
As for visibility, the rim is inevitably in view.
This is somewhat concerning in Simpson, where even free visibility is poor.
It is necessary in winter, but it is better not to have it in summer.
I own another Helmet from WINS and have been using it for about 3 years for commuting.
About halfway through the second year, the surface of the fog WIN deteriorated and the visibility became finely wavy.
Depending on the frequency of use, it may be advisable to replace them once every few years.
Adhesion seems fine and has not peeled or fogged up.
[Points to note]
Since it is a universal product, it is slightly smaller than the Shield.
Given the large size of Simpson's Eye Port, this may still be the limit.
If you put it on the upper limit, it may interfere with the opening and closing of the door, so it may be better to leave a little room.
How did it compare to other products?
Pin Lock Seat is also used on another Helmet.
While new, I didn't feel any superiority between Fog Win and Pin lock.
I thought the durability of Fog WIN seemed to deteriorate visibility more quickly.
Pin lock also had a gap early on and sometimes fogged up even after adjusting the Pin, so I can't say for sure.
Point and hang of installation
If you put it too high up, it is prone to interference.
[ITEMS TO BUY TOGETHER
Shield without pin lock support
[Opinions and requests to Manufacturer
I would appreciate it if it were cheaper so that I could easily replace it.
View detail
Pin lock.
I use AGV K5 S.
Shield was just getting WoundWound.
Due to unavoidable circumstances (laughs)
I scratched the shield on Asphalt surface and replaced the shield.
I didn't get the pin lock because I didn't know when it would be delivered, so I installed the one I've been using for a while, but hmmm, the pin is in the wrong position and I can't reach it (lol)
So I decided to go for the fog-in, which was recommended by Seiho.
There's an adhesive side to stick it to.
With pin lock, it gets more and more subtle (laughs).
I feel like this is better. Mm-hmm. (laughs)
I just put it on and will try it again and report back on how it works.
View detail