Reviews
For Maintenance
Light weight, good appearance
It's a good product
I was not sure about JTrip, but I am glad I chose this product.
View detail
lacking in stability
It lifts up, but while lifting it up, it shifted forward and fell off.
I'm glad I didn't remove the Tire.
I replaced it with a higher one to be raised by the same Manufacturer's Stem.
Maybe I was not using it properly, but I didn't understand it because it was not explained in detail.
Maybe people without knowledge should not use it.
View detail
I bought it for Race
[How is it used?
I used it to put on Tire warmer at Circuit.
Was the one you received as per Image?
It was just as Image.
How was your experience with it?
It is very easy to install and remove, so it is very useful in Circuit!
[Points to note]
Can be installed on any commercial vehicle body.
View detail
During car wash and wheel maintenance
It is designed for mini bikes, but the stem hole diameter is suitable, so I used it on the MT-10. Naturally, the Rear is supported by the maintenance stand. It takes a lot of force to raise it, but it works. However, it is not suitable for maintenance that requires a lot of force because it tends to wobble. In that case, it is definitely more stable to use a normal front stand.
Also, if the foot hangs at an angle halfway, the STAND of the Rear may gap.
View detail
Small Stand Hook.
I installed this Stand Hook on my SC59 CBR1000RR, and I have noticed that if the Stand Hook is long enough, the whole Swing Arm weld often flies off when the bike falls over. This Stand Hook is very small and I think it will minimize the damage when it falls over. I slip down once after installing the Stand Hook and the Stand Hook was not damaged. I also use the Rear Stand made by the same company, but the Stand Hook is not so small that it is difficult to lift up, and I think it is very easy to use. View detail
Very lightweight
This is a very lightweight STAND. Originally, we were using a STAND made by another company, but it was heavy and a little inconvenient when carrying it or loading it on the transporter. The Battle factory STAND we purchased this time is very lightweight and can be carried easily with one hand. The feel of the STAND is not a particular problem, but it is a little less rigid than the steel ones made by other companies, but I thought that was a trade-off with the lightness.:I like it because it is Stainless Steel and looks very Parenthesis. The bosses are set up differently for each car model, so you should be aware of that when purchasing. I highly recommend this product and I am very satisfied with it. View detail
Fits: HONDA NSR Mini, HONDA NSR50, HONDA NSR50, HONDA NSF100, HONDA NSF100
Good quality
A little expensive but good quality. View detail
Easy, easy to lift
It is a little heavy, but can be lifted easily.
It can be folded so it takes up little space in the Transporter.
The stability is there, too.
View detail
Commercial groms can be used without problems!
I bought this for daily maintenance and to wrap the tire warmer at the circuit. At first I thought I would have to take the headlight off to use it, but I had no problem at all and was able to lift it easily. Moreover, it can be folded up when not in use, so it can be stored without taking up too much space.
It was an excellent product.
View detail
Easy to lift!
[How is it used?
Circuit
Was the one you received as per Image?
Street Image
How was your experience with it?
It is easy to raise by the principle of lever, and I think even women can raise it. These products should be well-made, not cheap.
[Points to note]
How did it compare to other products?
Good cost performance. It is safe because it is a car model-specific product.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
Rear stand should be applied before use. Naturally…
View detail
I like that it's light and doesn't take up much space.
I have been using JTrip's STAND before and after for my 3.5 liter class, 250 class and NSF. It is very light due to the material. It also does not take up much space in the Transporter. However, I can't deny the instability while using it compared to JTrip's product mentioned above. That's why I gave it a Point4. I can't help it because of its shape. It also requires a certain amount of physical strength when you want to lift the vehicle. Women may find it a bit large. That's why I chose Point 3 for the work kill. However, JTrip's products are stable, but they take up a lot of space when stored. So I think you should choose one depending on your purpose. I am also satisfied with BF products. View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3
It can be used for the current model without any problem.
I've been using it on my current model since 2019 and it works perfectly fine.
I think the ease of use is the same for all models.
By the way, I used it for many years with Ape 50 and CB400SF.
View detail
Fits: HONDA CBR600RR, KAWASAKI ZX-6R, SUZUKI GSX-R600, SUZUKI GSX-R750, YAMAHA MT-09, YAMAHA YZF-R1, YAMAHA YZF-R6, HONDA CBR1000RR
Good product
The welds are very good and the weight is relatively light and easy to use
I've used other companies' products a few times before, but so far I like this one the best
Material:Stainless steel and looks durable, so it will work for the time being
The wheels are poorly made with plastic-like material
If you're concerned about it, I'd be happy to replace it
View detail
Fits: SUZUKI GSX-R1000, SUZUKI GSX1300R Hayabusa, KAWASAKI ZRX1100
Fender caught a little
Put the square under the Side Stand, bring the Motorcycle close to horizontal and hook the hook.
Then, the STAND slightly interferes with the tip of the Fender that is stuck with the OEM.
You can not set STAND unless you force it to push Fender away.
Fender Eliminator Kitetc. Although it seems to be an unrelated problem to the person who is making it clearer, it seems that it seemed to interfere a little bit with De Fault's GSX 1300 R HAYABUSA.
But Body is quite lightweight and easy to carry, so we are satisfied because the operability is also Outclassing.
View detail
Fits: KAWASAKI Ninja 250R, KAWASAKI Ninja 250R
Functional, exceptional storability!
We are looking for a Front stand that does not take up space for storage because it is being maintained at the bicycle parking lot in Apartment.
Although I did not understand how to use at all in the photograph and the explanatory note of the product page, since it was said that it was able to be used without problems with the Impression of others, I bought it with a half-trust.
Even if it arrives, handling Instruction Manual was not attached either. Anyway, when I apply it to Motorcycle, I see.
With the middle stick in the hole of Stem, lifting it on the principle of Lever, the part of the foot naturally supports the upright foot support.
It takes a little power when lifting, but it is enough for function.
Material : Because it is Stainless Steel, I do not seem to worry about Rust.
When used in conjunction with Rear stand, stability feeling seems no problem.
You will be able to exchange Tire and Front fork as well.
I feel that the price may be a little cheaper, but I think that this is only Compact, no other functional one.
View detail
Simple STAND, but finishing, ease of use, arrangement is wonderful.
Used for Warmer winding and Wheel exchange in Circuit.
Transporter got Small, I was suffering from loading, so purchase this product.
Simple STAND, but finishing, ease of use, arrangement is wonderful. Finish beautifully light. Transportter loading is preeminent because its dimensions are Compact.
The disadvantage is stability. Is stability feeling inferior to Large width in Roller type
Let's do until Wheel replacement.
Well, this Type is useless.
Also, the insertion point, the accuracy of the boss is too high Requires kitchen wear.
Those who are considering purchasing please check the system of the insertion mouth well. I can not use it because of a systematic difference
View detail
18in. It can also be used with Tire 's DREAM 50.
DREAM 50 has a Tire size of 18 in. So, Front-up Stand needs a certain height. With this STAND it is possible to detach Tire & Wheel with enough margin. Material : All Stainless Steel is a beautiful product. View detail
Fits: SUZUKI GSX-R1000, SUZUKI GSX1300R Hayabusa, KAWASAKI ZRX1100
Ease for women
I was surprised at this lightness, I can be happy with my work, and carrying it from my house to the Motorcycle bicycle parking lot is not a pain because it is lightweight.
Material is Stainless Steel, so I selected a material that is hard to rust
View detail
Fits: MORIWAKI MH80, HONDA NS-1, MORIWAKI MH80, HONDA NS-1
Simple and easy to use.
I use it for HONDA's NS-1. With Simple it is hard to break without fine parts, so Stainless Steel makes it easy to drop dirt that it got hard to rust. I thought that it was a bit expensive. View detail
Fits: SUZUKI GSX-R1000, SUZUKI GSX1300R Hayabusa, KAWASAKI ZRX1100
The STAINLESS STEEL was looked for. It is light and easy-to-use.
The STAINLESS STEEL was looked for.
It is light and easy-to-use.
View detail