Reviews
A-tech single seat cowl&seat
Received my single seat cowl and seat today and I'm very impressed with the quality of the items,I've offered the cowl up the the bike and the paint is a good match, the only reason it's not getting 5 stars is the time between buying and receiving the item. View detail
Lots of interference.
Purchased to prevent stains rather than to receive Oil.
Material:It is made of FRP and weighs 580g.
As is, there are no nests or hickeys, but there are many Small scratches and scuffs, so it is painted.
Lightly polished with #1000, sprayed with a buffing compound, and painted with 2-component urethane.
Cut because it interferes with Bracket and Hose near Side Stand, although it is not mentioned in other reviews.
Cut because it interferes with the IndonesiaFull Exhaust System that is being installed.
It was difficult because there were many parts to cut and a lot of cutting.
Prepare cutting and cutting tools for those who purchase them, as they are difficult to use with manual tools.
View detail
Used as Oil receiver for Circuit run
I installed it on my Ninja 250SL that I ride for Circuit Racing.
Since it is a dedicated product, it can be basically simply installed, but there may be some interference depending on the exhaust system being used.
I had OEM Exhaust System and YOSHIMURA Slip-on Silencer, but there was a little bit of shaving part.
View detail
For Dress-up
I don't race or anything, but it looked cool, so I put it on.
Since we did not feel the need to use carbon, we chose FRP, and the weight was about 650g.
There were some nests and wrinkles, but they were not exposed, so they were painted with Urethane Matte Black.
When I purchased the company's Under Cowl for 10R in the past, I was careful to handle it with Pe LePera, but this product has many rib-shaped folds and lines with the same thickness, which gives it a rigid and solid impression.
The 10R was not shaped in line with the frame and was prone to cracking, but this product is shaped to fit the cowl and frame firmly, which is a good thing.
The fit is good, but the hole for the well nut was gapped by half a child, so I corrected it with File.
The Cowl is covered from the front edge to the rear tire, which may have a rectifying effect.
The Rear Suspension Link area, which was hidden by the lunch box due to the installation of the Full Exhaust System, is now exposed, and since the engine area is also covered, it is likely to have an anti-fouling effect.
The thermal barrier Tape that comes with the product has a minimal area, so it is better to purchase an additional one.
A little more volume at the rear end would have been better.
View detail
Some processing is required.
Overall, the product is of good quality, but because it is FRP, the holes were misaligned in some places due to deformation and needed to be corrected.
Although it fits the Upper Cowl effectively, I was a little disappointed that there is a large gap between it and the Guide wing.
View detail
NinjaZX-10RRCarbon SeatWing
Normal, which does not fit in at all, has a Large keyhole, so it is naturally processed by File.
I have been purchasing a wide range of A-TECH Carbon products from exterior to Mirror for a long time!
Quality is commercial Material:It is No. 1 among Carbon products.
View detail
Concerned about strength of some parts
FRP was selected because the parts are not so heavy even in resin, and weighed about 600g.
I thought it would not need much strength, but when I held it horizontally by the edge, it made a squeaking sound, so I think it would be better to use Carbon if you are concerned about it.
The hole where the cowl is tightened with the frame is slightly out of alignment and the shape does not follow the frame.
I used Chinese Link pipe and needed to cut the back end, so I cut it with Grinder for Hobby.
Sandwiching type on the inside so there is no risk of scratching the OEMCowl, and it looks like a racing machine, which is cool.
View detail
Cool!
It was able to be attached to Striker's Full Exhaust System with almost no modification.
Accuracy was good and there was no distortion.
The only thing is that the Bracket on the STAND side interfered with it, so I had to shave it off to make a little escape.
Anyway, it is well designed and cool!
View detail
Parts with a strong presence.
The OEM is a combination of several parts, but this is a one-part unit. Therefore, two ScrewOne Sides are not used.
Still, it is firmly fixed, so there is no obstacle.
Acceptable, but some Screw position adjustment is required.
Changing this one makes me want to go Carbon on everything else!
View detail
BMW G310RFull Cowl for Race
Design with S1000RR as Motif is Parenthesis good.
The top speed, which is comparable to the non-cowl G310R with matching fuel condition, is considered to have good aerodynamic characteristics.
Of course, it is also good where the Style is different from NORMAL.
The feel of the ride is also different.
However, there is no detailed instruction manual on how to install the bracket, and the Upper Cowl Bracket is particularly difficult to install.
If you are not confident, you should ask Shop for help.
View detail
Full A-tech
The same shape as OEM, but the butt fixation has been changed to M4Screw.
It needs to be corrected by filling in the Pate around the groove, but I am generally satisfied with it.
View detail
A-tech
Seat circumference requires hole expansion rather than Nut fixation View detail
The construction is satisfactory.
It is used in the Circuit run.
As expected of an A-TECH product, the body is solidly built, and we do not feel any shortcomings even when using the circuit.
Even if the vehicle falls over, the Body will not crack unless the vehicle is struck by a vertical rotation.
It is that solid.
The U-shaped bracket that holds the Seat CowlRear side may break from the bent part, but it may not break so much in city driving.
Also, I don't think you have anything to worry about because Repair Parts will be provided immediately.
There is a Quick fastener lid on the Rear, and SeatRear could be used as an Accessory Case for city driving.
There are not many Other Brand Products for exterior parts for GS1200SS. (I know of only one other company that also offers Single Seat.) I think it is excellent from a Design standpoint.
I am using Circuit, so I have to modify some parts to match the vehicle specs, but I think fitting is no problem for a normal vehicle.
The only drawback is the slow delivery time due to made-to-order.
If you can tolerate that, it is a recommended Parts.
View detail
It's cool, I think.
I received the product and tried to fit it, but when I straddled it, the minimum ground clearance was about 5 cm. I tried to install the white Gel Coating, but it was not pure white because of the BALI removal. It is not usable unless it is painted.
I have a Wyvern two-pipe exhaust system, but if I don't remove it a little, the exhaust pipe hits me.
So I gave it away, unused and new.
I thought about painting it and attaching it, but decided against it because it would rub my stomach every time I went in and out.
I wanted to put it on since I am wearing a LunasoleCowl. It was a pity.
View detail
a little regret
This is a review of z900rs 21 year old ebony color genuine muffler vehicle installation. All A-Tech sticker manual bolts The reason is that even though the product is genuine, the holes did not fit well, so I tightened the bolts and then loosened them. I repeated the attach and reload. Other than that, I had a little trouble aligning the holes, but nonetheless, I installed it without any additional processing. I'm at a loss as I'm thinking of unpacking and installing it again on the ,,, ,,, This is a review of z900rs 21 year old ebony color genuine muffler vehicle installation. First of all, what is the under cowl heat dissipation sticker? A-tech sticker manual bolts are all There are pictures and descriptions in the manual, but it would be better if the pictures were a little more detailed. It is stated that the working time is about 30 minutes, but it took less than 2 hours with two people because it was the first time I installed it myself. The reason is that, despite the fact that the product is genuine, the holes did not fit well, so I tightened the bolts and then loosened them. I repeated the adda. Other than that, I had a little trouble aligning the holes, but I installed it without any additional processing. When I put it on, it definitely looks more full, it's pretty and I like it. However, I am thinking of unscrewing it and installing it again at the next engine oil change interval. It's hard, it's more than that,,,,,,, View detail
I think the installation would have to be done by a PRO.
Currently CB1300SC4 Parenthesis is a good idea, but it requires a sander to modify the bracket, and the only way to install it is to ask a motorcycle shop to do it for you. The wires and connectors are also large enough to put together. The Bracket is fixed to the Radiator, so if it rolls over, the Radiator will be damaged. This time, I had to order a special Bracket to use the STD Blinker. (A-TECH does not do this for us.) The paint on the Bracket is also messy, so I think it will rust quickly. But it looks cool, so it is irreplaceable. It took 6 months after I ordered. I have to endure the long delivery time. Overall, I am satisfied with the product. I like the fact that I can buy it at a lower price from WeBig. View detail
Received and happy overall
There was a 6 mth delay to get product made, but it was made and shipped within approx 2.5 months. Excellent email updating all the way from webike. Product was well packed. I got the black plain and the black gelcoat was a bit thin along a couple of tight edges but quality of glass was good. Holes did not quite line up but very near, and with a bit of coaxing it all went together. I could not get the final pushpin holes to line up enough, so haven't bothered with pinning those. Quite secure without them anyway. Now I can work on the bike without pulling off the large lower cowlings all the time. I do very little cold or wet riding nowadays. I confirmed the fit to OEM upper cowling before purchase. All up I'm very happy with the purchase and the service I have received. View detail
I'm happy with how it looks! But it's a pain to install!
I'm riding a SV650X 2018, with an S2 Katanacowl on it.
I've been wanting to get one of these for a long time. The reason is that I don't really do any serious circuit driving, I just want to look good and do StickerTune.
It took me about 2 or 3 months to receive my order. It is Corona season and everyone seems to be riding motorcycles and MotorcycleBoom. The manufacturer seems to be very busy, so I think it is inevitable.
I bought the BlackFRP without painting on the assumption that I would paint it myself. But it looks more beautiful than I expected, so I put it on without painting.
Impressions after installation
When you install it, it's pretty plain. Maybe that's the way it is...
If you stand beside it and look at it, it's pretty much nonexistent.
Also, heat will build up, and since there is no place for hot air from the engine to escape, hot air will come from the feet, which is characteristic of Full Cowl Motorcycles. (Well, it is natural because I put Cowl on.)
As a result, I'm taking it off the road in the summer.
Bad points
I've heard rumors, but frankly speaking, one of the brackets didn't attach properly. And I haven't installed it yet. (I'm going to ask the manufacturer about it.)
There is a part where the direction of the Instruction Manual and the actual Parts are different.
It comes with a thermal protection tape, but I have no idea where to put it when I install it.
It's around here! But as a result, it was burnt with hole in another place by heat. Please be careful everyone!
View detail
I can grin and bear it all by myself.
The OEM Side cover cracked so I took the plunge and bought this. You may need to use double-sided tape to replace the vibration absorber (?). You might want to prepare Double-sided Tape. I transplanted the original one because it was troublesome.
I remember that the Both Sides combined were almost 100 Grams lighter than the OEM.
It is a little less slippery, so I think it is easier to maintain the posture while turning.
I also like the fact that it doesn't look like I'm wearing Other Brand Product at first glance in a good way.
I'm giving it 4 stars because it takes a while to ship.
View detail
Beautiful workmanship.
Good texture, beautiful to fall in love with.
The price is high, but it can't be helped because it's Carbon.
I'm satisfied.
View detail