- Home
- Product reviews
- OEM Parts
- GENERATOR
- It does not seem to be semi-permanent. Older bod... (YAMAHA OEM Motorcycle parts: Rotor assembly 3HT-81450-10)
【YAMAHA OEM Motorcycle parts】Rotor assembly 3HT-81450-10 Review
Fits: YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400
It does not seem to be semi-permanent. Older bodies are by confirmation.
Flywheel was replaced at the same time when I had the engine overhaul the other day.
The rust was so bad that I thought it could still be used on Flywheel if I polished it, but I was worried about its strength after polishing, so I replaced it.
Flywheel
. bouncing wheel attached to the end of the crankshaft 。 It stores the rotational energy transmitted to the crankshaft, supplies it to the drive wheels, and helps the engine rotate by inertial force.
Not too light ? not too heavy ?.
[Symptoms of a problem with Flywheel
‥
▲Clutch does not disconnect, when Clutch is connected. "Skinny Vibrations and noises with a
▲Idling is not stable and vibration increases.
By the way, in my case, the Idling was going up and down and the vibration was terrible (laughs).
→Rust....
In fact, Flywheels are basically never worn out and can often be used for long periods of time.
*On the other hand, when it becomes unusable, it is rusted, corroded or chipped. In some cases, it can be reused by polishing. However, be careful not to polish it too much because it may lose its balance.
Replacement Procedure] Large body all car models are the same. For reference.
(1) Remove the Flywheel Cover and Sprocket Cover.
↓
Screw in the head of the MagnetFly Wheel Puller.
Prepare for the MagnetFly Wheel Puller because it cannot be removed without it.
↓
(3) Since it is an Opposite Thread Screw, it is tightened by turning it counterclockwise.
↓
Screw in the puller screw. 。 Normal Thread Screw.
↓
(5) Put the Spanner between the Head and the bar, and push the bar down to easily pull it out.
↓
(6) By turning the Shaft of the Puller and pushing in the head of the Crankshaft, the Flywheel comes out in front.
↓
(7) Flywheel is replaced and assembled in reverse order.
[After exchange]
◎Vibration reduction and Idling stabilized.
◎I am also worried about the durability of the Body itself if there is rust, and I am glad that I replaced it.
Idling is unstable due to the weight change caused by the rust and the Flywheel is not rotating and timing its rotation properly.
It is rare to replace a flywheel, but if you feel something is wrong or have an opportunity to open the crankcase, you should check it.
Incidentally, the Lightweight Fly Wheel improves the engine's response when the Axel is turned, and the change in rotation is quicker when the Axel is loosened. 。 RacerSpec. and so on.
In addition, Lightweight Fly Wheel seems to have better acceleration and deceleration performance because less Energy is required to change the Engine speed.
On the other hand, it seems that some people make it heavier in order to increase the sense of pulse...
If the Flywheel is made too light or too heavy, it will not be able to control the Rose Tsuki of the Engine combustion and the Idling will become unstable.
I think the safest thing to do is to replace the OEM.
OEM is 3HT-81450-10 is the part number.
ดูเหมือนจะไม่กึ่งถาวร ร่างที่มีอายุมากกว่านั้นได้รับการยืนยันแล้ว
มู่เล่ถูกเปลี่ยนพร้อมกับตอนที่ผมยกเครื่องเครื่องยนต์เมื่อวันก่อน
สนิมนั้นแย่มากจนฉันคิดว่ามันยังสามารถใช้กับ Flywheel ได้ถ้าฉันขัดมัน แต่ฉันกังวลเกี่ยวกับความแข็งแรงของมันหลังจากการขัดเงา ดังนั้นฉันจึงเปลี่ยนมันใหม่
มู่เล่
- ล้อเด้งที่ติดอยู่ที่ปลายเพลาข้อเหวี่ยง 。 โดยจะกักเก็บพลังงานการหมุนที่ส่งไปยังเพลาข้อเหวี่ยง ส่งไปยังล้อขับเคลื่อน และช่วยให้เครื่องยนต์หมุนได้ด้วยแรงเฉื่อย
ไม่เบาเกินไป? ไม่หนักเกินไปเหรอ?.
[อาการของปัญหากับมู่เล่
-
▲คลัตช์ไม่หลุดเมื่อเชื่อมต่อคลัตช์ "การสั่นสะเทือนและเสียงอันแผ่วเบาด้วยก
▲รอบเดินเบาไม่เสถียรและการสั่นสะเทือนเพิ่มขึ้น
ในกรณีของผม Idling ขึ้นๆ ลงๆ แรงสั่นสะเทือนก็แย่มาก (หัวเราะ)
→สนิม....
ในความเป็นจริงแล้ว มู่เล่ไม่เคยชำรุดและสามารถใช้งานได้เป็นระยะเวลานาน
*ในทางกลับกัน เมื่อใช้งานไม่ได้จะเป็นสนิม สึกกร่อน หรือบิ่น ในบางกรณีสามารถนำกลับมาใช้ใหม่ได้ด้วยการขัดเงา อย่างไรก็ตามระวังอย่าขัดมันมากเกินไปเพราะอาจทำให้เสียสมดุลได้
ขั้นตอนการเปลี่ยน] ตัวถังขนาดใหญ่รถทุกรุ่นเหมือนกัน สำหรับการอ้างอิง
(1) ถอดฝาครอบมู่เล่และฝาครอบเฟืองออก
ขันสกรูที่หัวของตัวดึงล้อ MagnetFly
เตรียมความพร้อมสำหรับเครื่องดึงล้อ MagnetFly เพราะไม่สามารถถอดออกได้หากไม่มีมัน
(3) เนื่องจากเป็นสกรูเกลียวตรงข้าม จึงต้องขันให้แน่นโดยหมุนทวนเข็มนาฬิกา
ขันสกรูตัวดึงเข้า . สกรูเกลียวธรรมดา
(5) วางประแจไว้ระหว่างส่วนหัวกับแฮนด์ แล้วดันแฮนด์ลงเพื่อดึงออกมาได้ง่าย
(6) ด้วยการหมุนเพลาของเครื่องดึงและดันเข้าที่ส่วนหัวของเพลาข้อเหวี่ยง มู่เล่จะออกมาด้านหน้า
(7) มู่เล่ถูกเปลี่ยนและประกอบในลำดับย้อนกลับ
[หลังการแลกเปลี่ยน]
◎การลดการสั่นสะเทือนและรอบเดินเบามีความเสถียร
○หากเกิดสนิมฉันก็กังวลเกี่ยวกับความทนทานของตัว Body เช่นกัน และฉันก็ดีใจที่ได้เปลี่ยนมัน
รอบเดินเบาไม่เสถียรเนื่องจากการเปลี่ยนแปลงของน้ำหนักที่เกิดจากสนิม และมู่เล่ไม่หมุนและกำหนดเวลาการหมุนได้อย่างเหมาะสม
การเปลี่ยนมู่เล่เป็นเรื่องยาก แต่ถ้าคุณรู้สึกว่ามีบางอย่างผิดปกติหรือมีโอกาสเปิดข้อเหวี่ยงก็ควรตรวจสอบ
บังเอิญว่า Fly Wheel น้ำหนักเบาช่วยปรับปรุงการตอบสนองของเครื่องยนต์เมื่อ Axel ถูกหมุน และการเปลี่ยนแปลงการหมุนจะเร็วขึ้นเมื่อ Axel ถูกคลายออก . RacerSpec. และอื่น ๆ
นอกจากนี้ Lightweight Fly Wheel ดูเหมือนว่าจะมีสมรรถนะการเร่งความเร็วและลดความเร็วที่ดีขึ้น เนื่องจากต้องใช้พลังงานน้อยลงในการเปลี่ยนความเร็วของเครื่องยนต์
ในทางกลับกันดูเหมือนว่าบางคนทำให้มันหนักขึ้นเพื่อเพิ่มความรู้สึกของชีพจร...
หากมู่เล่ถูกทำให้เบาหรือหนักเกินไป จะไม่สามารถควบคุม Rose Tsuki ของการเผาไหม้ของเครื่องยนต์ได้ และรอบเดินเบาจะไม่เสถียร
ฉันคิดว่าสิ่งที่ปลอดภัยที่สุดคือการเปลี่ยน OEM
OEM คือ 3HT-81450-10 คือหมายเลขชิ้นส่วน