【Z-WHEEL】R50 Rim Review
Fits: HUSABERG FE650, HUSABERG FE250-650, HUSABERG FE250, HONDA CRF450RX, HONDA CRF450R, HONDA CRF250R, YAMAHA YZ125, YAMAHA YZ125X, YAMAHA YZ250, YAMAHA YZ250X, YAMAHA YZ450F, KAWASAKI KLX650, KAWASAKI KLX450R, KAWASAKI KLX300R, KAWASAKI KLX250SR, KAWASAKI KLX250SR, KAWASAKI KLX250R (for competition), KAWASAKI KLX250ES, KAWASAKI KLX250, KAWASAKI KDX250SR,
They are a welcome addition to the relatively inexpensive market.
[How is it used?
It was decided to separate the SEROW225 WE wheel for mountain riding from the wheel for city riding, and since the rim for city riding is not easily scratched, it was decided to use the SEROW225 WE wheel for city riding. If we're going to go to the trouble, let's replace it with a colored Rim." and decided to use a Material with a slightly lower price.:I was looking for a color Rim for Aluminum and came across this product.
Since the Rear wheel is TubelessSpec. from SEROW225 WE, it is a deceptive Custom Start to reduce expenses by sticking RimDecal on the Rear and buying only Front rim.
How did you like it?
I have been using it without any problems and have not experienced any troubles at this point.
The following is a detailed discussion.
The aluminum rims are beautiful enough when seen from the outside with the tires installed, but the reverse side of the rim is a little more beautiful. (Tire mounting side) has solid weld marks and the welds are slightly distorted. (This is a part that only the person who does the assembly work would understand.) These are the areas that differentiate us from DID's and RK's slightly more expensive Rim.
However, conversely, if we consider that the price is reduced by omitting some processing of details that do not cause problems in use, it can be said that this is a product that is appreciated by the user.
How did it compare to other products?
Like I wrote above. The Finish Difference." If you don't mind that, I think you will be able to accept it without problems.
Color variations are also available. Silver, Black, Red, Blue, Green Light The variety of products is abundant and should meet the needs of most people.
The color of the product I purchased this time was black, so it is difficult to distinguish the difference in color. However, the color of blue and green light may differ slightly from one manufacturer to another, so I recommend that you check the actual product before purchasing if possible.
[Points to note]
Although the adhesion is stronger than that of paint, it is inevitable that wounds will appear on the surface if the work is done carelessly.
Other items that would be helpful
The deciding factor in the purchase
The price is by far the lowest among Aluminum rims with Anodized staining!
[How is it used?
SEROW225 WE for mountain play "For city driving." The Wheel is used as the Wheel of the
As I mentioned above, I can't use Universal Product for the Rear hole, so MDF's OffRim sticker. is pasted to match the front and rear Image.
【Included Parts:presence or absence】.
RimBody and something like a light warranty is Quantity:1 pc., sent in corrugated ball.
[ITEMS TO BUY TOGETHER
*More than anything else, it takes a lot of time and effort. If you are not confident, it may be better to leave it to PRO. (Labor charges will be added separately.) 。
If you are assembling a new Wheel. Hub." Ya Spoke." is required, not necessary if only the Rim of the existing Wheel set is to be replaced.
If the wheel is a transplant from a wheel in good condition, there is no problem, but if it is an old one, take this opportunity to replace the bearingetc. of the hub, and the Spoke should be new as much as possible.
After assembly, distortion and balance must be corrected, and a balancer and nipple wrench are also needed.
Opinions and requests to Manufacturer.
I can't say enough good things about the price and the variety of color variations.
Responses
Other reviews
The swing was strong.
Quantity on runout table in temporary assembled state:When I Set it, there was quite a bit of runout. I don't know since I bought it for the first time, but I wonder if there are individual differences. I struggled with it a bit, but it was within acceptable limits.
Installed it on the car body and went to the forest road! The impact from the road surface was lessened and it became easier to drive.
View detail
It was more than I expected... ♪
There was almost no runout of the rim, and it was almost complete in a temporary assembly state. It looks good and cool.
I drove a little on a forest road, and my impression is that the shock transmitted to the vehicle body was less and it became very easy to ride.
View detail
More than the price
I bought it to build it into my KLX250 from Carburetor Vehicles
To be honest, I wasn't expecting much, but out of the box, Big Li?
The texture of Anodized is high You're good, right? It was like
The holes in the Bead stopper are also drilled in the face of the Valve, and so on For some reason, there is a vacancy in the 90-degrees area for OEMs
Even the weld seams were treated by Beauty, which I thought was more Beauty than OEM
I'm not going to use it in a race, so I don't know if I need to go out of my way to buy XXK or D*D or something. lol
About assembly→ you will need a dedicated Nipple; Spoke is a cheap To give it a go, I polished the OEM and used it around LOL!
The machining accuracy is good, or maybe it's just a matter of applying Tension to Spoke, but the runout is small and easy We were able to take the runout to
Instruction ManualQuantity of a simple piece of paper:It's 1pc. so it would be nice if it had a few more instructions I'm sure the only people who buy this product are the ones who know that... lol
I'm very happy with the way it looks and the rarr; I'm already satisfied with Large It will look like a Motocrosser
I bought it as a replacement for a distorted Rim, but for the price of an OEM, outside RimSingle Item The price is so reasonable that I can even buy Nipple, which is very helpful
Only the Front was exchanged and it rode, but it was drawn by the goodness of Parenthesis, and it was sober I bought the Rear as well LOL!
View detail
Used for KX125 K1 in 1994
It is a replacement because the rim cracked. My model has a front desk, but there is no rear (We ordered excel) The aluminum nipple could also be exchanged without any problems. Just offset was aimed at the center, but my KX seems to be offset toward Left. By the way, OEM nipple does not fit. View detail
Z-WHEEL Ze Wheel
I bought for WR250F
My WR is 2013 USMODEL Rear wheel size is 1. It is 85.
Z-WHEEL Ze Wheel R 50 It is Rim, when Size is 2. Size up to 15
(Front will be same size)
What I thought was good was that in the case of WR 250 F, Nipple could use Yamaha OEM Product as it was
OEMSpoke could also be used
Depending on the model, you need to replace Nipple with Z - WHEEL, but you can check the compatibility chart that marks this area as well
Of course the product itself is satisfied
However, the Bead stopper is accompanied by Size up 2. 15 is necessary for replacement
As a digression I tried Challenge to Rim exchange at DIY with this purchase
At that time I purchased DRC Gyro Stand
This is also easy to use, there are also videos of how to use it is safe for the first time
View detail