【brembo】GP4-RB CNCRadial Mount Brake CaliperKit P4 30/34 Quantity:Pair (for Left and Right) Review
Fits: HONDA CB1000 R, HONDA CB1000 R, HONDA CBR 1000 RR, HONDA CBR 1000 RR, HONDA CBR 1000 RR, HONDA CBR 1000 RR, HONDA CBR 1000 RR, HONDA CBR 1000 RR, HONDA CBR 1000 RR, HONDA CBR 1000 RR SP, HONDA CBR 1000 RR SP1, HONDA CBR 1000 RR SP2, HONDA CBR 1000 RR-R, HONDA CBR 600 RR, HONDA CBR 600 RR, HONDA CBR 600 RR, HONDA CBR 600 RR, KAWASAKI Z 1000, KAWASAKI Z 1000, KAWASAKI Z 1000,
notebook
It was my first time to install a custom one except for the Slip-on Silencer, but it was very convenient to have everything at Webike. I don't think the large ring will be the same, but since the brembo installation was my goal, I'm happy with that.
Except, memorandum.
■Preparations
Adapter (306-03-32CBK) 、Adapter (306-03-32CBK) →Quantity:2pc. Set、Adapter (CPL-823-03C) 、Adapter (5130-03C) 、Adapter (B593L-03CBK) 、Adapter (B593R-03CBK) 、Hose (B30070S、110mm,385mm,285mm,485mm) Small diameter mounting bolt M10?60mm→ 4 pcs, brake fluid 500mm, 3-way adapter height adjustable collar
Rear Stand、Stand Hook
Phillips Screwdriver, Glasses Wrench Set, Air bleed Pump and Tube, Spanner set, Flare nut wrench 11mm and 14mm, Torque wrench, Socket set, Nipper, Brake lever lock
Gloves, Paper waste, Curing Tape, Masking sheet, Newspaper, Parts cleaner, Seal tape, Molybdenum grease, Anti-seize lubricant, Thailand lock
■Work Details
Ignition will not start until key removal is completed.
Rear Stand:Raise the Rear with the Rear Stand.
Cure the painted surface with masking sheet or newspaper to protect the WheelBoth Sides surface and the Fluid Tank area from Fluid.
Remove the Fluid from the Fluid Tank and clean it lightly.
：Quantity:Pair (for Left and Right) Siphon off the brake fluid from the caliper using the air bleed pump and tube. Do not forget to open and lock the nipple.
Remove the hose from the MASTERCylinder side first, and install a new hose immediately so that the installation position will not be lost.
Hose mouth cure and dustcloth to prevent sagging.
Seal tape is used for banjo bolt.
Molybdenum grease is used in the Screw section.
SUS tightening torque18-22Nm (As a result, all were hand Torque.)
*Hose to be secured with Thailand locks in place.
A height matching collar for 3wayAdapter is required separately. 5mm approx.
：Quantity:Pair (for Left and Right) Remove the caliper. Be careful that the caliper does not fall off and damage the wheel or other parts when loosening it.
New Item Quantity:Pair (for Left and Right) Temporarily fasten Caliper with Mount Bolt to the extent that it is lightly tightened.
Connect both calipers and banjo bolt to each other.
Seal tape to banjo bolt
When tightening the banjo bolt, make sure that the socket is inserted into the caliper mount bolt and allow the banjo adapter to escape slightly outward.
*Tightening Torque20 with M10 (17-25) Nm
Put the Brake fluid into the Fluid Tank.
：Quantity:Pair (for Left and Right) Use the air bleed pump and tube from the caliper, open the nipple and vape, refill the Fluid Tank when it is low, and lock the nipple tightly when brake fluid comes out of the caliper side. After the fluid has been sucked out, return it to the Fluid Tank.
Repeat until the Brake lever becomes firm.
When the brake lever becomes hard, bleed air from the Caliper side and the MASTER side so that the Fluid Tank will never be empty.
Hold the brake lever several times→Loosen the Nipple while holding the brake lever→Tighten the Nipple when all the brake levers are gripped→Repeat this several times.
*Tightening Torque12~16Nm
Fill the tank to UPPER level with brake fluid and tighten the Fluid Tank Cap. If necessary, replace the diaphragm.
Caliper:thin coat of anti-seize agent on M10Bolt and 46Nm of Caliper. (34-38) The main closing is done at the
Wash the car just in case there may be Fluid adhering to it.
:Leave the Brake lever in your grip overnight.
Test run:test run.
Responses
Other reviews
Functional parts only
Installed on a GSX-R1000R 2019
I wanted to try a proper brembo because the OEM brembo had a bad reputation and I wanted to see what a proper brembo was like.
It was a considerable expense for the sole purpose of satisfying that curiosity…
Below is a comparison based on an OEM Szumbo with Metallica Pad.
In the selection process, the product is a 4-pod with a different diameter of Φ30/34 compared to Suzumbo's Φ32 4-pod with the same diameter.
but in the end, the total area of Piston is almost the same, so there is no problem without MASTER change.
In fact, the softness of the Touch after the replacement was about "the difference in the accuracy of the air bleed? The difference was about "the difference in the accuracy of air venting?
Incidentally, I think Φ19/18-20 is appropriate to match with MASTER of Other Brand Product.
In the case of the Suzumbo displacement, Offset is 14mm.
Also, it is stated that the Caliper Mount Bolt does not fit the diameter of the seat unless it is a special product, but the SEA BASSOEM Mount Bolt for SEA BASSOEM can be used without any problem.
The serviceability of the banjo bolt is free from the stressful Bleeder bolt of the Szumbo, but on the other hand, the banjo bolt hole and the Caliper Mount Bolt hole are close together, so care must be taken when tightening the banjo bolt, otherwise the Caliper Mount Bolt will be inaccessible. However, the banjo bolt hole and the Caliper Mount Bolt hole are close together.
Quality of the exterior is a bit subtle considering the price.
Although the cut-outs have a high quality at first glance, a closer look reveals some anodized irregularities, small wounds, and protruding logo paint, which may be slightly disappointing when viewed as design parts.
However, it is not hard to understand if you look at it as a hard-edged component that has been designed with function in mind.
The key is that the feel of the product is excellent.
I think the absolute value of the braking force is more than the same etc. while the Control at the beginning of the grip is easier to do.
Considering the fact that the comparison is with Metallica Pad, "brembo" is indeed a good thing.
Well, I guess it depends on your sense of value whether you can find the value of less than 200,000 yen in this difference in experience;
View detail
Brembo caliper, worth the price?
BlackBillet caliper, a new color for the 220 Series of brembo CNCCaliper.
The price is high, but the red Brembo letters on the black body are cool.
The motorcycle brake consists of many parts, from the master cylinder to the hose, caliper, pad, and disc rotors, and each is customized in combination with the others. In fact, this may be the most difficult part of motorcycle customization.
The most important point of the brembo Billet caliper is its resistance to heat and stable braking force even after repeated hard braking. In particular, the movement of the piston when the brake is released is outstanding.
The high performance related to hard braking seems to be the essence of this Caliper, so if it is used for riding without hard braking, it may become nothing more than a dress-up part.
Finally, I would like to list the good and bad points of this Caliper.
good point
1.High heat resistance and hard brake durability.
2. Lightweight
3.Piston's move away from Rotor is excellent.
4.Looks cool.
5.Many options for Brake Pads.
6.Can be installed on any car model as long as it is MountSize compatible.
A bad point
1.price
2.Standard Pad doesn't work very well.
3.Gold amount for Overhaul is high.
4.Requires dedicated Mount Bolt.
I would recommend it to those who can do overhaul by themselves and use it for a long time.
View detail
Pricey, but cool!
It is a pontoon on CBR600RR 2021.
Spacer and others are not required.
However, the OEM Caliper has a different banjo bolt position than the OEM Caliper, so the length of the hose is slightly different.
At the same time, we replaced the hose with a stainless steel mesh hose, but since the hose for the car model is still too long, we purchased a slightly shorter hose separately for the part that connects to the Caliper.
Aluminum forged cut-out black alumite body with Red lettering "Brembo" Very cool that it says "I'm not a fan of this"!
The quality is by far better than the cheaper cast brembo, so if you have the budget, we recommend the CNC brembo.
It is also recommended for those who are concerned about the weight under Spring, as it seems to be lighter than P4 due to a newer design than P4, although it is in the same price range as P4 of the same CNC.
I wish it were cheaper, but it is brembo, so I guess it can't be helped.
View detail
Red Logo on the shaved Black.
Installed on MT-09
Master Cylinder：GALE SPEEDVRC Φ 17.5
Hose：Buildaline
Offset adapter：PLOT
The installation itself was easy, but it took some time to bleed the air since the Hose is with it.
Manufacturer recommends the Φ19 Master Cylinder, but I think Gail's Φ17.5×Ratio18mm is a good brake with good control.
By the way, if you use Ratio16, it won't stop for lack of capacity.
If you prefer Snap, I think you'll like the Φ19.
View detail