【DID】Kashimaru #50 Series Set Review
This is it! Well done!
Although it is expensive, it was surprisingly easy to replace the chain when the essentials were grasped and used. The chain I bought was too long, so I cut it with the same number of links.
Cut:Cut the head of LINK with File until there is almost no difference between LINK and Chain. Cut Kashimaru-kun to Quantity:I checked the position of the LINK and Shimamaru-kun and tightened Shimamaru-kun's Screw halfway around to check the position gap. Then, the screw was easily pulled out.
Press-fitting:Apply plenty of grease to the O-ring and surrounding area, and press-fit the plate. When the screw tightening becomes heavy, remove the "Kashimaru-kun" and check the press-fit condition. Check the height of the plate by applying Scale to the next Chain Plate and the press-fit Plate as shown in the photo!
Crimping:Kashimaru-kun is rearranged for Crimping and Crimping begins. After the machine is heavy, check the Crimp condition and confirm that there is not enough Crimp by comparing with the picture in the instruction manual. As shown in the picture, take the side to be crimped in your hand and check the gap between the plate and the crimp. If there is a gap, the Crimp is insufficient. Re-qualify the Crimp.:Set and crimp the screw, and when the screw became heavy, check the crimp condition again and this time it was OK.:The second pc was the same, and I was able to Crimp the second time, so I felt that I did not have to break Kashimaru-kun if I thought about completing the press-in and Crimp in the second time, rather than finishing it in the first time.
After the test run, it was found that there was no problem, and the results were good.
Now that I understand how to use it, I would like to use this Kashimaru-kun for Large things.
Responses
Other reviews
easy to use
Easy to use
Daido has Daido, you can trust him.
View detail
520Chain Exchange
I purchased this for Chain replacement.
It is easy to understand if you DID watch YouTube before working on it.
hang carefully and accurately.
View detail
I finally bought it.
[How is it used?
I bought this to replace Chain.
I've been wanting to get one for a while,
This is a moderately high-end product, isn't it?
It's been 10 years since I put it off, thinking about how many times I'll have to replace the Chain before I die,
I decided to buy it because I mainly play Race and I thought that the frequency of Chain exchange would be there as well.
How was your experience with it?
The Instruction Manual was properly included so I could use it with peace of mind.
I used to use tools like Chain Tool only or Crimp only and I would ruin them quickly. (I would like to believe that my usage was not good)
It can be used simply because it has few configuration parts.
Also, the cans DID look stylish. Cool.
When I opened the lid, it was skunky, so I put the Sponge that came with Brake Pads underneath to make a Cushion.
[Points to note]
I think it will not be a problem if you read the basic Instruction Manual, but you might want to buy a spare pin for cutting.
If it breaks, the motorcycle will not be able to run!
View detail
No failure because it does not tighten beyond the specified value.
I replaced the 520Chain of Kashime Joint by myself for the first time.
It was a difficult Image, but with the Chain Cut & Crimp tool, the old Chain Pin removal and attachment,
The new Chain was easily press-fitted and kinked.
Chain Cut & Crimp tools are designed to prevent over-tightening during press-fitting and crimping.
I was able to complete my arrival with peace of mind because I was there.
View detail
Nicely done.
It's not something I use often, but it's a hassle to take it to the shop, and it's convenient to have it on hand, so I bought it.
I've had the experience of buying cheap ones in the past and having them break down quickly.
I thought it was a bit expensive, but it was the right decision.
As expected from ChainManufacturer, the construction is solid.
It is easy to use.
Recombination of parts and Quantities:The set position can be changed to perform a series of operations from cut to press-fit to crimp, which is very well thought out.
Plate press fit and Crimp to the specified values, respectively.
We tightened it up several times while measuring the dimensions.
The work was completed smoothly and without problems.
View detail