【DRC】M6 Aluminum Spacer Φ18 Review

Try it with Bolt of your choice.

[How is it used?
I purchased this product to refresh the exterior fixing bolt of SEROW225WE, which has been used for more than 20 years and has become rusty and lickable.
It is a convenient Spacer that kills two birds with one stone as it is highly universal and looks good because it can be easily matched with Bolts of 12.4π or smaller in size.
Was the one you received as per Image?
Although it is treated as a separate frame from the Spacer made by DRC that I purchased before, it is useful because the design and large size are the same, so I feel no sense of discomfort.
The price is just a little bit higher than the last DRCAluminum spacer I purchased, but it is still Reasonable enough and just like the Image.
Was the installation difficult?
There is nothing difficult about this product, which is installed by biting it in place of a washer when fixing the bolt.
How was your experience with it?
previously sold by each Manufacturer. FUJI TUBO type. Since the outer diameter is larger than that of the Cap Holder, the Cap Holder may not be used in places where there is a depression.
Unlike FUJI TSUBO Type products, this product has a relatively large number of Bolts that can be combined, so the impression of the appearance can be changed depending on the design of the BoltHead, and it can show various faces depending on the financial power (since the price goes up and down depending on the shape and material of the BoltHead) and Sense. (Since the price goes up and down depending on the shape and material of the BoltHead) and Sense.
The coloring of Anodized is also vivid, and I will continue to use it and see how it fades due to UV rays.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
I really wanted to buy the Red 20-pack, but it was already discontinued, so I could only buy the 4-pack.
We would like to see the 20-packs revived as the price per unit is slightly lower.
The product itself is not disappointing as I like the look and feel of the purchase.
One of the most common Anodized products is Fading due to ultraviolet rays, etc. However, the same DRC-made Spacer that we purchased previously also maintains the same coloring as when we purchased it, so we can expect durability as well.
It may be better to check the actual product if possible, as there are some people who like or dislike the color of the same Red.
Other items that would be helpful
Point and hang of installation
Since it is like a fashion color used in place of a washer when fixing a bolt, it is a simple job to use this product (Aluminum Collar) by biting it when attaching a cap bolt of the appropriate length to the bolt stop on the part where it can be attached.
[Availability and clarity of the Instruction Manual
No Instruction Manual is available
The ease of use is top level, so I don't think it's likely to be used incorrectly.
[Notes]
As mentioned above, the outer diameter is Larger Thicker than the FUJI TSUBO Type color, so you need to check if you want to install it on an exterior with a dimple.
[ITEMS TO BUY TOGETHER
If the bolt is M6 size and the head size is 12.4π or smaller, it is likely to be Large body and Large sturdy, but Bolts with good parenthesis design are expensive, so please consult with your Wallet and get the right bolt. Please consult with your wallet.
I have attached an image of a few different Bolts that I had at home together, and I would be grateful if you could help me with something.
[Opinions and requests to Manufacturer
I strongly hope you will bring back the 20-pack.
Please continue to sell the product itself as much as possible. View detail

Black has been discontinued!

[How is it used?
The bolt that holds the exterior of the car started to rust, and I couldn't shake the feeling of disappointment after having gone to the trouble of making up the car with the Decal Kit.
Was the one you received as per Image?
The outer diameter was larger than expected and could not be used in places with a small depression, but on the other hand, the appearance of the large size could be used to disguise places where the mounting holes are gapped, so I think it was a good purchase for the right place for the right person.
Was the installation difficult?
There is nothing difficult about this product, which is installed by biting it in place of a washer when using Bolt.
How was your experience with it?
Used for other types of vehicles FUJI TUBO type. Compared to the Cap Holder, it is more like a fashionable washer that fits well with modern motorcycles.
However, the shape of the Head of the Bolt to be combined changes the look and feel of the Bolt, which is a bit troubling for middle-aged people with limited finances and Sense (the HeadDesign makes the CoolBolt very pricey...).
As for the product, the coloring of Anodized is vivid, and there is nothing to say, I am only worried about the fading caused by UV rays.
[Included Parts:were they on?
None
20Quantity at the time of purchase:4Quantity because the Set version was no longer available.:Buy the set
When I opened the product introduction page to write a review, I found 4Quantity:I was also troubled by the fact that the Set version was no longer available.
[Was there anything that disappointed you?
I like the way it looks and I buy it. As expected. It was
As there are Anodized products The colors are not what I saw in the pictures." If possible, it may be safer to check the actual product at a motorcycle accessory store before purchasing.
Other items that would be helpful
Point and hang of installation
As mentioned above, it is like a fashion color used in place of a bolt washer, so it is a simple job to use this product (Aluminum Collar) when attaching a cap bolt of the appropriate length to the bolt stop on the attachable part.
[Availability and clarity of the Instruction Manual
No Instruction Manual is available
The ease of use is top level, so I don't think it's likely to be used incorrectly.
[Notes]
No special requirements. The outer diameter is Large, so please check if you want to install it on an exterior with a depression.
[ITEMS TO BUY TOGETHER
If the Bolt does not have a large head in M6 size, it is likely to be large body and large sturdy, but Bolts of good parenthesis design are expensive, so please consult with your wallet before you buy them. Please consult with your wallet.
[Opinions and requests to Manufacturer
Although this product is no longer available, it would be very much appreciated if another product with the same shape and color is continuously sold, so please continue to sell that product as much as possible. View detail

Great texture and awesome looking!

As you can see from the pictures, it's very cool!
It's kind of luxurious…Motorcycle as a whole is tightened up.
Buy a Spacer in a color that matches your car's body color for a more attractive look!
Recommendation! View detail

Unnecessary but awesome

I get more comments on the trick washers from Zeta products, Gives the bike a WORKS look.What do you say about a of washers? Necessary? No, but if you can justify the cost they're aluminum, won't corrode, look cool and are lightweight. This is an easy way to get your bike closer to that factory look without breaking the bank.. Super lightweight, perfect size for gas tank bolt, radiators, and 2 stroke exhaust mounts. I'd buy another if I had the place to put them. View detail

One of the few with Stages

I needed a Washer with Stages to attach an Aluminum Bolt, and since I couldn't find a good size, I ordered a DRCCap bolt, expecting it to be Large and sturdy.
The result was that the batch Size was Exactly.

Shroud and side cowl were fixed, dress-up and lightened.

20 pieces Quantity:It is unfortunate that Set has been discontinued. View detail