【DAYTONA】High Spec Line Brake Hose Type A Review
Fits: YAMAHA VMAX , HONDA FTR223, KAWASAKI GPZ900R, KAWASAKI KSR-1, KAWASAKI KSR-2, KAWASAKI ZRX1100, KAWASAKI ZRX1100II, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZZR400, YAMAHA VMAX, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MAJESTY250(4HC), YAMAHA YZF-R1, YAMAHA YZF-R25, YAMAHA YBR250, YAMAHA YZF-R1,
Used for ybr 125
I wanted to replace the normal hose on my YBR125 after 20,000 km and to improve the brake touch. There are many cheaper products available, but we chose DAYTONA because we want to use a reliable manufacturer for the brake.
Purchased Type A 850mm. The banjo bolt is NORMAL and the crush washer is Copper Washer.
After the replacement, the tightness of the brake is much better than with NORMAL, and it is easier to control the brake strength. In addition, the lever position at which the brake is effective is quite shallow. (far from Throttle) The design is not too obvious and is very pleasing. The design is not too obvious, but it is a nice touch.
Responses
Other reviews
Cheap but reliable.
I sometimes hear that external Stainless Steel Mesh Hose has lost its caulk, but this product is made of OEM material.:It is manufactured by NICHIRIN, TopShare of RubberBrake hose, and all products have been inspected.
It is not only reliable, but also cheaper and more cost-effective than other companies' products.
Even if you use it to replace the brake line of an older vehicle that is no longer supplied by the OEM, you can be assured of the same quality as the OEM, and you can also get the tight touch that is typical of Stainless Steel Mesh Hose.
View detail
Good cost performance and durability
I have heard that the Brake hose with aluminum banjo is lightweight, but it can break at the slightest impact, so I am considering changing it.
Material:Stainless Steel is expensive, so I purchased this product, which is Steel but made of Stainless Mesh.
I purchased the shortest 550mm, but it is a little long for my Motorcycle and I wish there was a shorter Type.
One point to note is that Banjo is 8mm thick, thinner than other Manufacturers' products, and when connected to APRACING's CP2696
Banjo bolt has bottomed out.
So, I changed the Caliper side crush washer to a 3mm thicker one, and it did not bottom out, and I was able to install it without any problems.
(Crash washer on Bolt side is 2mm because the holes of Hose and Bolt are not aligned.)
From now on, I can ride with confidence in its good looks and durability.
View detail
cheap
The touch is as good as any other manufacturer's. It is steel, so how about rust? It looks good, not hideous, but functionally oriented. After all, it is inexpensive. View detail
Normal good
I used to use a cheap Brake hose that I won a bid on Yahoo auctions, but the corrosion of the gold part and the Brake fluid seeped out when pressure was applied due to hose deterioration I bought and installed this Brake hose from Brand and saw it
So far it's working fine
I'm not sure how long this will last, but from the looks of it, I think it's a quality that will last a long time
View detail
this is good
It looks good, but it's Brake solid
It got hard
Caliper's stiffness, etc., is a problem
To a solid Fee Ring before that
It will be
Looks, length and orientation, no problem
View detail