【Vesrah】Resin Brake Pad Review
Fits: BMW F650 GS, Others 600 Super Motard, BETA Jonathan 125, BMW C1, BMW C1 200, BMW F650 CS, YAMAHA TT600RE, YAMAHA BWs125, APRILIA SL750 Shiver GT ABS, YAMAHA WR125X Supermoto, BMW F650, Others VR250 Super,Otard, Others VR250 Enduro, Others Supermotard 610, Others TK, Others SR ZF13.0 J.Juan Calipers, Others S 570E Super Motard, Others S 501 Super Motard, Others SR 600 Motard Racing, Others SR 450 Motard Racing,
It works fine
Rear Brake Pads for BWS125 were replaced.
It was very well worn and after the replacement it was very good.
The brake fluid had not been replaced after delivery, so the front and rear were replaced as well.
Responses
Other reviews
Necessary and sufficient efficacy
I am using it with KawasakiZ1.
We are on Double disk with OEMCaliper.
Is it thanks to the Shim on the back of the Pad?
No squeaking so far.
Braking force, but it does not perform Race.
It works well enough for the TouringLevel's muddy driving.
If you say that this Pad does not stop, then that is too much Speed.
View detail
Maintenance
I replaced the Front Brake Pads on my Z1R with Vesra's. The pads no longer squeal and I can break without worry. I don't know about the durability yet. View detail
SD-401 should be called the old one.
Using it as it is, it is like that to begin with, but even the double disk on the 650RS W3 only works vaguely.
Especially with Solid's Rotor without Slit, it is the worst in the rain, it doesn't work as well as it should.
This is an area where I would like to ask manufacturers if they can do something about the friction material.
We are working very hard to stop squeaking and increase braking power, but the methodology is a secret.
To increase braking force with the old Tokico Caliper, the Caliper design philosophy must be revised.
Also, the Package was changed from the one I purchased this time, and the Pad has a groove, but the inside of the Pad is not the same as the one I purchased this time. (Fixed side) the groove is in the radial direction of Rotor, but the outer (Piston side) But unbelievably, the grooves are circumferential.
I would like to ask Vesla what he is thinking on this point.
View detail
GOLD WING1500SE R replacement
I decided to go with Resin because of the Record board pattern on the Metal pad, it is thicker and the braking force is ?approximately right.
To make the most of the braking power, we polished the Brake Disc to remove the record pattern. After a light test ride, it was perfect!
Disc Rotor is also ? expensive, so disc friendly is the best.
For the time being, the Rear area is Large sturdy.
View detail
malformation
I had bought Besra because it didn't squeak Brake.
The exchange would normally have taken 30 minutes to complete.
The Pad I purchased this time holds the Brake lever.
Glitch that does not return at all.
Initially, I inspected the vehicle body side Braque hydraulic failure and installation defects many times.
Not at all. I asked my go-to Shop and no luck.
It took me 3 hours to give up and put a pad with 200km on it.
Successfully installed and BreakingOK.
The Piston grounding surface of the Pad on the B side of this purchase was in poor shape.
It was a problem with the Pad not returning.
Get a store that specializes in OH.
"Drove 200km, Pad attached to front." is made by Besra.
What's this?
I did the maintenance myself and the Brake squeal went away.
I'm assuming you just happened to hit a defective product in a production lot.
Vesla's credibility has suffered.
Caliper is hurt and angry.
View detail