- Home
- Product reviews
- Motorcycle Parts
- Exhausts
- Other Exhaust Options / Repair Parts
- Glass Wool Replacement... (STRIKER: Silencer Repair)
【STRIKER】Silencer Repair Review
Glass Wool Replacement
I purchased this Rivet set to replace the Glass Wool on my Striker Bolt on silencer that I bought used about 5 years ago. This Rivet set is the same silencer as the Full Exhaust System, with 11 4mm diameter Rivets to hold the IN and OUT pieces, 4 reinforced Rivets to hold the Boomerang to hang the spring for fixing, and 2 small diameter Rivets to hold the JMCAPlate. There were two small diameter Rivets to hold the JMCAPlate. I did some research beforehand. [Contents] However, the Silencer I have from Bolt On does not need a Rivet to hold the Boomerang, and the shape of the IN side piece seems to be different, so I needed a 4.8mm diameter Rivet to hold it (I bought it used, so it may have been modified). (I bought it used, so it may have been modified.) In the end, we used only 5 Rivets to fasten the OUT piece, and had to buy a new Rivet to fasten the IN piece.
This Rivet is a Material:It seems to be a ShieldType of Stainless Steel, which prevents the ball of the head of the shaft from falling inward, so that no relics can fall inside the Silencer.:The Stainless Steel construction requires a bit of force to fasten, but I was able to fasten it properly with the Hand Riveter.
Quantity:We only used a portion of the Set, but the five we did use stayed in place nicely, so we are satisfied.
เปลี่ยนใยแก้ว
ฉันซื้อชุดหมุดย้ำนี้เพื่อใช้แทนใยแก้วบน Striker Bolt บนท่อเก็บเสียงที่ฉันซื้อมาใช้เมื่อประมาณ 5 ปีที่แล้ว ชุด Rivet นี้เป็นอุปกรณ์เก็บเสียงแบบเดียวกับ Full Exhaust System โดยมี Rivet เส้นผ่านศูนย์กลาง 4 มม. 11 ตัวเพื่อยึดชิ้นส่วน IN และ OUT, Rivets เสริม 4 ตัวเพื่อยึด Boomerang เพื่อแขวนสปริงเพื่อยึด และ Rivet เส้นผ่านศูนย์กลางขนาดเล็ก 2 ตัวเพื่อยึด JMCAPlate มีหมุดย้ำขนาดเส้นผ่านศูนย์กลางเล็กสองตัวสำหรับยึดแผ่น JMCAPlate ฉันได้ทำการวิจัยบางอย่างล่วงหน้า [เนื้อหา] อย่างไรก็ตาม Silencer ที่ฉันมีจาก Bolt On นั้นไม่ต้องการหมุดย้ำเพื่อยึดบูมเมอแรง และรูปร่างของชิ้นส่วนด้านข้าง IN ดูเหมือนจะแตกต่างออกไป ดังนั้นฉันจึงต้องการหมุดย้ำขนาดเส้นผ่านศูนย์กลาง 4.8 มม. เพื่อยึดมัน (ฉันซื้อมา ใช้อยู่จึงอาจมีการแก้ไข) (ซื้อมาใช้แล้วอาจดัดแปลง) สุดท้ายเราใช้ Rivet เพียง 5 ตัวในการยึดชิ้น OUT และต้องซื้อ Rivet ใหม่เพื่อยึดชิ้น IN
Rivet นี้เป็นวัสดุ: ดูเหมือนว่าจะเป็น ShieldType ของ Stainless Steel ซึ่งป้องกันไม่ให้ลูกของหัวเพลาตกลงไปด้านใน เพื่อไม่ให้มีเศษวัสดุตกลงไปใน Silencer: โครงสร้าง Stainless Steel ต้องใช้แรงเล็กน้อย เพื่อยึด แต่ฉันสามารถยึดมันได้อย่างถูกต้องด้วย Hand Riveter
ปริมาณ: เราใช้เพียงบางส่วนในชุด แต่ 5 ชิ้นที่เราใช้ยังคงอยู่อย่างดี เราจึงพอใจ