【Neofactory】Glass Wool 3.0mm x 1.2m x 1m for Exhaust System Review
Fits: HARLEY-DAVIDSON Universal
Silencer Inner Replacement
I bought this to replace the Glass Wool on Striker's Bolt on silencer that I purchased used about 5 years ago.
Since there was information that Ceramic coated Glass Wool is more durable, we wanted to use Ceramic coated Glass Wool for all of our Glass Wool if possible, but since it would be over our budget if we had the necessary amount, we initially thought of using a combination of DAYTONA's Ceramic coated Glass Wool and this product. However, the budget for the required quantity was over our budget, so we initially thought of using a combination of DAYTONA's Ceramic coated Glass Wool and this product. However, we saw information that stainless wool wrapped around the punching part improves the inner durability, so we purchased additional stainless wool, and decided to combine stainless wool, DAYTONA's Ceramic coated Glass Wool, and NeoFACTORY's Glas Wool. We decided to use a three-layer structure of stainless wool, DAYTONA's Ceramic coated Glass Wool, and NeoFACTORY's Glass Wool.
For the wrapping method, relying on the information I found on the Net, I wrapped it with moderate strength, made the inner thicker than the silencer outer, pushed it into the outer to compress the glass wool, wrapped two rounds of stainless steel wool around the punching part, wrapped the needle gold around it and fixed it in place. Then, I wrapped the punching part with Stainless wool twice and fixed it by wrapping the needle with Gold, wrapped the Ceramic coated Glass Wool from DAYTONA on top of it, and finally wrapped the Glass Wool from NeoFACTORY and fixed it by wrapping the needle with Gold to complete the Silencer. The sound was not so different from before the Silencer was replaced, partly because the condition of the inner was not so bad before the replacement.
The Glass Wool is large enough, so we decided to use 3 layers of Glass Wool, which resulted in a small amount of remaining material. I am not sure how durable it will be in the future since it has just been assembled, but I am very satisfied with the low cost of the project.
Responses
Other reviews
TE250i for Silencer.
I purchased this Glass Wool because the Exhaust System sound of my TE250i was getting DrumstickDrumstickDrumstickDrumstick noisy.
Silencer removal
↓
Remove 4 Bolt and pull out the contents.
↓
Wrap new Glass Wool and temporarily fix with masking tape
↓
Assemble in reverse order to complete.
(Gloves, Mask and Glasses are required)
After the replacement, the volume became quieter with a thump-thump-thump.
If you are looking for Silencer for KTM/Husk/GasGas system, this productQuantity:The large size can be replaced twice in 1 pc! (I think it costs about 5,000 yen if you buy OEM product)
Now I'm hoping for durability.
View detail
It is inexpensive and appreciated when using larger quantities.
[How is it used?
When I restored my Honda XR250, a famous car from a bygone era, I found that the external exhaust system that had been installed since the day I received the car was not working properly in today's environment. Noisy Exhaust System. I purchased this product to muffle the sound as much as possible because it had become a
Was the one you received as per Image?
It was exactly as it looks, Glass Wool (GlassMatte), so it was just like Image.
How was your experience with it?
"twill weave" The fabric is not woven into the fabric like other fabrics, so it is easy to unravel, which is both a merit and a demerit.
The price is low for that reason, and it is a very nice product when you want to use it in Large quantities.
[Points to note]
If the frayed glass fibers get on your skin, they will sting, so it is best to wear disposable rubber gloves and avoid exposing your skin to the elements when working.
It is even safer if you also wear a mask to avoid inhaling through the nose or mouth, as they are easily disintegrated.
How did it compare to other products?
It is a large quantity and inexpensive, and is a great product for use in exhaust systems and other sound deadening measures.
Other items that would be helpful
Point and hang of installation
However, if the coil is left rolled and assembled without being secured, it will be unevenly distributed due to exhaust pressure or will gradually scatter during driving.
After winding the tape strongly, I think it will last a little longer if it is wound GRUGRU with fine needle goldetc. to prevent it from shattering.
[ITEMS TO BUY TOGETHER
However, it is important to prepare tools for disassembling the Silencer part of the Exhaust System (Chamber) (Drill for disassembling the Rivet stop, Riveter for assembling the Rivet stop, and Rivetc. of appropriate size). Riveter & Rivet of appropriate size).
After that, it might be a good idea to have a fine needle Gold as mentioned above.
[Opinions and requests to Manufacturer
I have purchased several times because of the quantity and low price, please continue to offer them at low prices.
View detail
To SilencerOH.
[How is it used?
I ride a YZ250 for Enduro fun.
I bought this one because it's been making a lot of noise lately and I wanted to OH it.
I think it's good manners to be as quiet as possible considering the recent Course environment. Also, the Torque will return.
How was your experience with it?
It will be one of the most annoying work, but it is a Recommendation work for those who play with Enduro because the Torque will be increased when rewinding.
How did it compare to other products?
It was in stock and arrived quickly.
Some people roll residential ones, but I recommend this one because it's half the volume.
[Points to note]
Because the silencer of YZ250 is elliptical, it is necessary to wrap the Glass Wool to the elliptical well.
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
You should buy Wire for Grip because you put it together with Wire.
https://www.webike.net/sd/23616697/
View detail
To Silencer Refresh of CR80
In order to divert the CR 80 Silencer to the CRM 50, we acquired second hand and selected this product for reference of that other's reference for that Refresh.
Main wound up with Ceramic coating of DAYTONA and rolled up the missing part with this product.
Since the sound does not change much even after winding, I think that COSPA is good.
View detail
Volume improvement of Exhaust System
Because I felt that the volume of the Exhaust System which had not exchanged silencing material for over 10 years was getting louder, purchased for Japanese Vehicle Inspection Correspondence.
In order to reduce the consumption of Glass Wool, we rolled CeramicWool 2 turns and then wound up the Gloucescool for NeoFACTORY's Exhaust System to fill the gap of Exhaust System.
I think that this combination is very good durability and Cost's Balance, and the volume at the time of purchase - I think that it is possible to pass a vehicle inspection without problems because it is close to sound quality.
View detail